[yocto] wic status

[Maciek Borzecki]

On czw, 2014-07-17 at 09:18 -0500, Tom Zanussi wrote:
> On Thu, 2014-07-17 at 14:51 +0100, Paul Eggleton wrote:
> > On Thursday 17 July 2014 16:48:41 Scott Rifenbark wrote:
> > > On Thu, Jul 17, 2014 at 3:56 PM, Paul Eggleton <
> > > paul.eggleton at linux.intel.com> wrote:
> > > > On Thursday 17 July 2014 14:25:16 Maciek Borzecki wrote:
> > > > > There used to be an entry about wic in development manual back in 1.5.2:
> > > > > http://www.yoctoproject.org/docs/1.5.2/dev-manual/dev-manual.html
> > > > > 
> > > > > This entry is gone in current documentation and there seems to be no
> > > > > mention of wic at all:
> > > > > https://www.yoctoproject.org/docs/current/dev-manual/dev-manual.html
> > > > 
> > > > Scott, can you take a look at this if you haven't already?
> > >
> > > wic was documented in the 1.5.x set and was not put into the 1.6 set.  I
> > > was told that it was going to change or be further completed so it did not
> > > go in that development branch.  Wic was never documented in the 1.6 set.
> > 
> > Well, wic is still a part of the system in 1.6 and beyond so we do need to 
> > document it; as far as I can tell what was in the 1.5 manual linked above 
> > should be perfectly fine and we can just extend / update it as needed. Tom 
> > should be able to help fill in any blanks.
> > 
> 
> Right, wic is still included in the system, and like the rest of the
> system is undergoing continual development, so I'm not sure why it would
> be treated differently.
> 
> In any case, to make it easier for users and to avoid a mismatch with
> external documentation, over the past couple weeks I've submitted a set
> of patches (which have now been merged) that puts most of the help
> content into the tool itself, which is all now accessible via 'wic
> help'.

Right, I've seen your patches in master, very helpful.

There's one more thing that I'm a bit confused about. The 1.5.2 docs
state the following:

<excerpt start>
Here are the actual partition language commands used in the
mkefidisk.wks file to generate an image:

     # short-description: Create an EFI disk image
     # long-description: Creates a partitioned EFI disk image that the
user
     # can directly dd to boot media.

     part /boot --source bootimg --ondisk sda --fstype=efi --label msdos
--active --align 1024
<excerpt end>

I'd assume to find scripts/lib/mic/plugins/source/bootimg.py in the
tree, but the file is not there. Have I missed something? 

(btw. I'm also assuming that bootimg would prepare a boot partitiong
without pushing any particular bootloader, like syslinux or whatever
right?)


-- 
Maciej Borzęcki
Senior Software Developer at Open-RnD Sp. z o.o., Poland
www.open-rnd.pl
mobile: +48 889 117 365, fax: +48 42 657 9079

Niniejsza wiadomość wraz z załącznikami może zawierać chronione prawem
lub poufne informacje i została wysłana wyłącznie do wiadomości i
użytku osób, do których została zaadresowana. Jeśli wiadomość została
otrzymana przypadkowo zabrania się jej kopiowania lub rozsyłania do
osób trzecich. W takim przypadku uprasza się o natychmiastowe
zniszczenie wiadomości oraz poinformowanie nadawcy o zaistniałej
sytuacji za pomocą wiadomości zwrotnej. Dziękujemy.

This message, including any attachments hereto, may contain privileged
or confidential information and is sent solely for the attention and
use of the intended addressee(s). If you are not an intended addressee,
you may neither use this message nor copy or deliver it to anyone. In
such case, you should immediately destroy this message and kindly notify
the sender by reply email. Thank you.