[meta-ti] which kernel for pandaboard?
Denys Dmytriyenko
denys at ti.com
Fri Nov 16 16:05:55 PST 2012
On Fri, Nov 16, 2012 at 04:56:53PM -0500, Cliff Brake wrote:
> I'm trying to boot a recent oe-core+meta-oe+meta-angstrom+meta-ti on a
> pandaboard. With 3.4, I get the attached. With 3.1, I get the below:
3.4 should work. With 3.1 there were some reports that it didn't boot, when
built with recent toolchain from oe-core... What problems do you have with
3.4? Does it boot?
Denys
> Environment size: 686/131068 bytes
> Panda # boot
> reading boot.scr
>
> ** Unable to read "boot.scr" from mmc 0:1 **
> reading uImage
>
> 4175588 bytes read
> Booting from mmc0 ...
> ## Booting kernel from Legacy Image at 82000000 ...
> Image Name: Linux-3.1.0
> Image Type: ARM Linux Kernel Image (uncompressed)
> Data Size: 4175524 Bytes = 4 MiB
> Load Address: 80008000
> Entry Point: 80008000
> Verifying Checksum ... OK
> Loading Kernel Image ... OK
> OK
>
> Starting kernel ...
>
> Uncompressing Linux... done, booting the kernel.
>
> (nothing more)
>
> What is the suggested path to get a pandaboard booting?
>
> Thanks,
> Cliff
>
> --
> =================
> http://bec-systems.com
> U-Boot SPL 2011.12-dirty (Nov 16 2012 - 15:17:13)
> Texas Instruments OMAP4430 ES2.0
> OMAP SD/MMC: 0
> reading u-boot.img
> reading u-boot.img
>
>
> U-Boot 2011.12-dirty (Nov 16 2012 - 15:17:13)
>
> CPU : OMAP4430 ES2.0
> Board: OMAP4 Panda
> I2C: ready
> DRAM: 1 GiB
> MMC: OMAP SD/MMC: 0
> Using default environment
>
> In: serial
> Out: serial
> Err: serial
> Hit any key to stop autoboot: 0
> reading boot.scr
>
> ** Unable to read "boot.scr" from mmc 0:1 **
> reading uImage
>
> 4340608 bytes read
> Booting from mmc0 ...
> ## Booting kernel from Legacy Image at 82000000 ...
> Image Name: Linux-3.4.11
> Image Type: ARM Linux Kernel Image (uncompressed)
> Data Size: 4340544 Bytes = 4.1 MiB
> Load Address: 80008000
> Entry Point: 80008000
> Verifying Checksum ... OK
> Loading Kernel Image ... OK
> OK
>
> Starting kernel ...
>
> Uncompressing Linux... done, booting the kernel.
> [ 0.000000] Booting Linux on physical CPU 0
> [ 0.000000] Initializing cgroup subsys cpuset
> [ 0.000000] Initializing cgroup subsys cpu
> [ 0.000000] Linux version 3.4.11 (cbrake at mars) (gcc version 4.7.2 (GCC) ) #1 SMP PREEMPT Fri Nov 16 15:24:49 EST 2012
> [ 0.000000] CPU: ARMv7 Processor [411fc092] revision 2 (ARMv7), cr=10c5387d
> [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
> [ 0.000000] Machine: OMAP4 Panda board
> [ 0.000000] cma: CMA: reserved 8 MiB at 98800000
> [ 0.000000] cma: CMA: reserved 112 MiB at 99000000
> [ 0.000000] cma: CMA: reserved 32 MiB at ad800000
> [ 0.000000] cma: CMA: reserved 16 MiB at ac000000
> [ 0.000000] Memory policy: ECC disabled, Data cache writealloc
> [ 0.000000] omap2_set_globals_tap
> [ 0.000000] OMAP4: Map 0xad600000 to 0xfe600000 for dram barrier
> [ 0.000000] omap2_set_globals_tap
> [ 0.000000] OMAP4430 ES2.0
> [ 0.000000] PERCPU: Embedded 8 pages/cpu @c12ec000 s11712 r8192 d12864 u32768
> [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 259584
> [ 0.000000] Kernel command line: console=ttyO2,115200n8 vram=16M root=/dev/mmcblk0p2 ro rootfstype=ext4 rootwait
> [ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
> [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
> [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
> [ 0.000000] allocated 2097152 bytes of page_cgroup
> [ 0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups
> [ 0.000000] Memory: 726MB 296MB = 1022MB total
> [ 0.000000] Memory: 851860k/851860k available, 196716k reserved, 270336K highmem
> [ 0.000000] Virtual kernel memory layout:
> [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
> [ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
> [ 0.000000] vmalloc : 0xf0000000 - 0xff000000 ( 240 MB)
> [ 0.000000] lowmem : 0xc0000000 - 0xef800000 ( 760 MB)
> [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
> [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
> [ 0.000000] .text : 0xc0008000 - 0xc0857db0 (8512 kB)
> [ 0.000000] .init : 0xc0858000 - 0xc08b9dc0 ( 392 kB)
> [ 0.000000] .data : 0xc08ba000 - 0xc093a7a8 ( 514 kB)
> [ 0.000000] .bss : 0xc093a7cc - 0xc0ae2a04 (1697 kB)
> [ 0.000000] SLUB: Genslabs=11, HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
> [ 0.000000] Preemptible hierarchical RCU implementation.
> [ 0.000000] NR_IRQS:538
> [ 0.000000] omap_sr_disable: omap_sr struct for sr_wakeup not found
> [ 0.000000] OMAP clockevent source: GPTIMER1 at 32768 Hz
> [ 0.000000] sched_clock: 32 bits at 32kHz, resolution 30517ns, wraps every 131071999ms
> [ 0.000000] Console: colour dummy device 80x30
> [ 0.000274] Calibrating delay loop... 1590.23 BogoMIPS (lpj=6213632)
> [ 0.070312] pid_max: default: 32768 minimum: 301
> [ 0.070617] Security Framework initialized
> [ 0.070678] AppArmor: AppArmor initialized
> [ 0.071044] Mount-cache hash table entries: 512
> [ 0.072875] Initializing cgroup subsys cpuacct
> [ 0.072937] Initializing cgroup subsys memory
> [ 0.072998] Initializing cgroup subsys devices
> [ 0.073028] Initializing cgroup subsys freezer
> [ 0.073028] Initializing cgroup subsys net_cls
> [ 0.073059] Initializing cgroup subsys blkio
> [ 0.073120] Initializing cgroup subsys perf_event
> [ 0.073333] CPU: Testing write buffer coherency: ok
> [ 0.073455] ftrace: allocating 22900 entries in 68 pages
> [ 0.143890] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
> [ 0.144226] hw perfevents: enabled with ARMv7 Cortex-A9 PMU driver, 7 counters available
> [ 0.144409] Setting up static identity map for 0x8059d348 - 0x8059d3a0
> [ 0.144439] L310 cache controller enabled
> [ 0.144470] l2x0: 16 ways, CACHE_ID 0x410000c4, AUX_CTRL 0x5e470000, Cache size: 1048576 B
> [ 0.144470] omap_sar_ram_init
> [ 0.144744] generating sar_ram layout...
> [ 0.144958] sar ram layout created
> [ 0.223022] CPU1: Booted secondary processor
> [ 0.292663] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
> [ 0.292694] CPU1: Unknown IPI message 0x1
> [ 0.292724] Brought up 2 CPUs
> [ 0.292755] SMP: Total of 2 processors activated (3188.82 BogoMIPS).
> [ 0.293762] devtmpfs: initialized
> [ 0.299346] omap_sr_disable: omap_sr struct for sr_core not found
> [ 0.299377] omap_sr_disable: omap_sr struct for sr_core not found
> [ 0.299407] omap_sr_disable: omap_sr struct for sr_core not found
> [ 0.299438] omap_sr_disable: omap_sr struct for sr_core not found
> [ 0.299468] omap_sr_disable: omap_sr struct for sr_core not found
> [ 0.299499] omap_sr_disable: omap_sr struct for sr_core not found
> [ 0.299530] omap_sr_disable: omap_sr struct for sr_iva not found
> [ 0.299560] omap_sr_disable: omap_sr struct for sr_core not found
> [ 0.299591] omap_sr_disable: omap_sr struct for sr_core not found
> [ 0.299621] omap_sr_disable: omap_sr struct for sr_iva not found
> [ 0.299652] omap_sr_disable: omap_sr struct for sr_core not found
> [ 0.299682] omap_sr_disable: omap_sr struct for sr_iva not found
> [ 0.299743] omap_sr_disable: omap_sr struct for sr_core not found
> [ 0.299804] omap_sr_disable: omap_sr struct for sr_core not found
> [ 0.299835] omap_sr_disable: omap_sr struct for sr_core not found
> [ 0.299865] omap_sr_disable: omap_sr struct for sr_core not found
> [ 0.299896] omap_sr_disable: omap_sr struct for sr_core not found
> [ 0.299957] omap_sr_disable: omap_sr struct for sr_core not found
> [ 0.299987] omap_sr_disable: omap_sr struct for sr_core not found
> [ 0.300842] omap_sr_disable: omap_sr struct for sr_iva not found
> [ 0.300872] omap_sr_disable: omap_sr struct for sr_iva not found
> [ 0.300994] omap_sr_disable: omap_sr struct for sr_iva not found
> [ 0.301025] omap_sr_disable: omap_sr struct for sr_iva not found
> [ 0.301055] omap_sr_disable: omap_sr struct for sr_iva not found
> [ 0.303741] omap_hwmod: mcpdm: _wait_target_ready error: -16
> [ 0.303771] omap_sr_disable: omap_sr struct for sr_iva not found
> [ 0.303771] omap_hwmod: mcpdm: cannot be enabled (3)
> [ 0.304077] omap_sr_disable: omap_sr struct for sr_iva not found
> [ 0.304107] omap_sr_disable: omap_sr struct for sr_iva not found
> [ 0.304138] omap_sr_disable: omap_sr struct for sr_iva not found
> [ 0.304168] omap_sr_disable: omap_sr struct for sr_iva not found
> [ 0.305389] omap_sr_disable: omap_sr struct for sr_iva not found
> [ 0.305938] dummy:
> [ 0.322235] NET: Registered protocol family 16
> [ 0.335205] DMA: preallocated 256 KiB pool for atomic coherent allocations
> [ 0.335632] GPMC revision 6.0
> [ 0.337554] gpiochip_add: registered GPIOs 0 to 31 on device: gpio
> [ 0.337615] OMAP GPIO hardware version 0.1
> [ 0.337829] gpiochip_add: registered GPIOs 32 to 63 on device: gpio
> [ 0.338104] gpiochip_add: registered GPIOs 64 to 95 on device: gpio
> [ 0.338378] gpiochip_add: registered GPIOs 96 to 127 on device: gpio
> [ 0.338623] gpiochip_add: registered GPIOs 128 to 159 on device: gpio
> [ 0.338928] gpiochip_add: registered GPIOs 160 to 191 on device: gpio
> [ 0.339996] omap_mux_init: Add partition: #1: core, flags: 2
> [ 0.341094] omap_mux_init: Add partition: #2: wkup, flags: 2
> [ 0.342864] omap_mux_get_by_name: Could not find signal uart1_cts.uart1_cts
> [ 0.342895] omap_hwmod_mux_init: Could not allocate device mux entry
> [ 0.346466] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers.
> [ 0.346496] hw-breakpoint: maximum watchpoint size is 4 bytes.
> [ 0.349212] Updated GPU clock source to be dpll_per_m7x2_ck
> [ 0.350952] omap-mcbsp.1: alias pad_fck already exists
> [ 0.351135] omap-mcbsp.2: alias pad_fck already exists
> [ 0.351318] omap-mcbsp.3: alias pad_fck already exists
> [ 0.351501] omap-mcbsp.4: alias pad_fck already exists
> [ 0.352539] OMAP DMA hardware revision 0.0
> [ 0.353149] emif emif.1: Device configured with addr = f0e00000 and IRQ142
> [ 0.353393] emif emif.2: Device configured with addr = f1000000 and IRQ143
> [ 0.359283] bio: create slab <bio-0> at 0
> [ 0.360076] vwl1271: 1800 mV
> [ 0.360290] vhub: 3300 mV
> [ 0.360473] hsusb0: 3300 mV
> [ 0.360504] hsusb0: supplied by vhub
> [ 0.362274] SCSI subsystem initialized
> [ 0.362670] omap2_mcspi omap2_mcspi.1: master is unqueued, this is deprecated
> [ 0.363037] omap2_mcspi omap2_mcspi.2: master is unqueued, this is deprecated
> [ 0.363311] omap2_mcspi omap2_mcspi.3: master is unqueued, this is deprecated
> [ 0.363616] omap2_mcspi omap2_mcspi.4: master is unqueued, this is deprecated
> [ 0.363922] usbcore: registered new interface driver usbfs
> [ 0.364013] usbcore: registered new interface driver hub
> [ 0.364135] usbcore: registered new device driver usb
> [ 0.364624] omap_i2c omap_i2c.1: bus 1 rev2.4.0 at 400 kHz
> [ 0.365112] Skipping twl internal clock init and using bootloader value (unknown osc rate)
> [ 0.365692] twl 1-0048: PIH (irq 39) chaining IRQs 416..436
> [ 0.366180] VUSB: 3300 mV normal standby
> [ 0.369293] twl6030_usb twl6030_usb: Initialized TWL6030 USB module
> [ 0.369812] V1V8: 1800 mV normal standby
> [ 0.370117] V2V1: 2100 mV normal standby
> [ 0.370544] VMMC: 1200 <--> 3000 mV at 3000 mV normal standby
> [ 0.371215] VPP: 1800 <--> 2500 mV at 1900 mV normal standby
> [ 0.371917] VCXIO: 1800 mV normal standby
> [ 0.371948] VCXIO: supplied by V2V1
> [ 0.372863] VDAC: 1800 mV normal standby
> [ 0.372863] VDAC: supplied by V2V1
> [ 0.373657] VAUX2_6030: 1200 <--> 2800 mV at 1800 mV normal standby
> [ 0.374267] VAUX3_6030: 1000 <--> 3000 mV at 1200 mV normal standby
> [ 0.374969] CLK32KG:
> [ 0.375274] VANA: 2100 mV normal standby
> [ 0.375640] omap_i2c omap_i2c.2: bus 2 rev2.4.0 at 400 kHz
> [ 0.375915] omap_i2c omap_i2c.3: bus 3 rev2.4.0 at 100 kHz
> [ 0.376281] omap_i2c omap_i2c.4: bus 4 rev2.4.0 at 400 kHz
> [ 0.376556] Linux media interface: v0.10
> [ 0.376586] Linux video capture interface: v2.00
> [ 0.377044] omap-iommu omap-iommu.0: dsp registered
> [ 0.377136] omap-iommu omap-iommu.1: ipu registered
> [ 0.377288] Advanced Linux Sound Architecture Driver Version 1.0.25.
> [ 0.377868] NetLabel: Initializing
> [ 0.377899] NetLabel: domain hash size = 128
> [ 0.377899] NetLabel: protocols = UNLABELED CIPSOv4
> [ 0.377960] NetLabel: unlabeled traffic allowed by default
> [ 0.378479] Switching to clocksource 32k_counter
> [ 0.398284] FS-Cache: Loaded
> [ 0.398498] AppArmor: AppArmor Filesystem Enabled
> [ 0.411468] NET: Registered protocol family 2
> [ 0.411804] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
> [ 0.412536] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
> [ 0.414489] TCP bind hash table entries: 65536 (order: 7, 786432 bytes)
> [ 0.415588] TCP: Hash tables configured (established 131072 bind 65536)
> [ 0.415588] TCP: reno registered
> [ 0.415618] UDP hash table entries: 512 (order: 2, 16384 bytes)
> [ 0.415649] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
> [ 0.416015] NET: Registered protocol family 1
> [ 0.416229] usbhs_omap usbhs_omap: ehci_logic_fck failed:-2
> [ 0.480865] omap-rproc.1: alias fck already exists
> [ 0.481689] omap_sr_disable: omap_sr struct for sr_iva not found
> [ 0.481781] omap_sr_disable: omap_sr struct for sr_iva not found
> [ 0.481872] omap_sr_disable: omap_sr struct for sr_iva not found
> [ 0.481964] omap_sr_disable: omap_sr struct for sr_iva not found
> [ 0.483001] audit: initializing netlink socket (disabled)
> [ 0.483062] type=2000 audit(0.437:1): initialized
> [ 0.577575] highmem bounce pool size: 64 pages
> [ 0.584381] VFS: Disk quotas dquot_6.5.2
> [ 0.584716] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
> [ 0.587860] fuse init (API version 7.18)
> [ 0.588195] msgmni has been set to 1471
> [ 0.590118] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
> [ 0.590301] io scheduler noop registered
> [ 0.590301] io scheduler deadline registered
> [ 0.590362] io scheduler cfq registered (default)
> [ 0.591308] OMAP DSS rev 4.0
> [ 0.619873] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
> [ 0.621276] omap_uart.0: ttyO0 at MMIO 0x4806a000 (irq = 104) is a OMAP UART0
> [ 0.621704] omap_uart.1: ttyO1 at MMIO 0x4806c000 (irq = 105) is a OMAP UART1
> [ 0.622100] omap_uart.2: ttyO2 at MMIO 0x48020000 (irq = 106) is a OMAP UART2
> [ 1.806335] console [ttyO2] enabled
> [ 1.810485] omap_uart.3: ttyO3 at MMIO 0x4806e000 (irq = 102) is a OMAP UART3
> [ 1.818817] [drm] Initialized drm 1.1.0 20060810
> [ 1.832061] brd: module loaded
> [ 1.839172] loop: module loaded
> [ 1.842712] (stk) :sysfs entries created
> [ 1.846923] (stk) : debugfs entries created
> [ 1.856536] Fixed MDIO Bus: probed
> [ 1.860382] tun: Universal TUN/TAP device driver, 1.6
> [ 1.865844] tun: (C) 1999-2004 Max Krasnyansky <maxk at qualcomm.com>
> [ 1.872894] PPP generic driver version 2.4.2
> [ 1.877777] usbcore: registered new interface driver smsc95xx
> [ 1.884246] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
> [ 2.031890] ehci-omap ehci-omap.0: OMAP-EHCI Host Controller
> [ 2.038238] ehci-omap ehci-omap.0: new USB bus registered, assigned bus number 1
> [ 2.047912] ehci-omap ehci-omap.0: irq 109, io mem 0x4a064c00
> [ 2.066101] ehci-omap ehci-omap.0: USB 2.0 started, EHCI 1.00
> [ 2.072479] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
> [ 2.079772] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
> [ 2.087524] usb usb1: Product: OMAP-EHCI Host Controller
> [ 2.093231] usb usb1: Manufacturer: Linux 3.4.11 ehci_hcd
> [ 2.099060] usb usb1: SerialNumber: ehci-omap.0
> [ 2.104583] hub 1-0:1.0: USB hub found
> [ 2.108642] hub 1-0:1.0: 3 ports detected
> [ 2.144256] Initializing USB Mass Storage driver...
> [ 2.149597] usbcore: registered new interface driver usb-storage
> [ 2.156066] USB Mass Storage support registered.
> [ 2.161102] usbcore: registered new interface driver libusual
> [ 2.167266] musb-hdrc: version 6.0, ?dma?, otg (peripheral+host)
> [ 2.374969] musb-hdrc musb-hdrc: USB OTG mode controller at fc0ab000 using DMA, IRQ 124
> [ 2.384185] mousedev: PS/2 mouse device common for all mice
> [ 2.392181] twl_rtc twl_rtc: Enabling TWL-RTC
> [ 2.400207] twl_rtc twl_rtc: rtc core: registered twl_rtc as rtc0
> [ 2.407043] i2c /dev entries driver
> [ 2.412475] omap_wdt: OMAP Watchdog Timer Rev 0x00: initial timeout 60 sec
> [ 2.420440] device-mapper: uevent: version 1.0.3
> [ 2.425781] device-mapper: ioctl: 4.22.0-ioctl (2011-10-19) initialised: dm-devel at redhat.com
> [ 2.437103] omap_hsmmc.0 supply vmmc_aux not found, using dummy regulator
> [ 2.441101] usb 1-1: new high-speed USB device number 2 using ehci-omap
> [ 2.560089] omap_hsmmc.4 supply vmmc_aux not found, using dummy regulator
> [ 2.605590] usb 1-1: New USB device found, idVendor=0424, idProduct=9514
> [ 2.612670] usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
> [ 2.620910] hub 1-1:1.0: USB hub found
> [ 2.625061] hub 1-1:1.0: 5 ports detected
> [ 2.677001] thermal_governor_dev_register:Adding omap_ondie_governor governor
> [ 2.684570] thermal_get_slope:Getting slope is not supported for domain cpu
> [ 2.691986] thermal_get_offset:Getting offset is not supported for domain cpu
> [ 2.699859] thermal_governor_dev_register:Adding omap_ongpu_governor governor
> [ 2.707550] thermal_get_slope:Getting slope is not supported for domain gpu
> [ 2.715026] thermal_get_offset:Getting offset is not supported for domain gpu
> [ 2.722839] stm_fw: vendor driver stm_ti1.0 registered
> [ 2.737792] omap_pcm_dummy() init
> [ 2.741729] OMAP4/5 SoC init
> [ 2.744812] omap_pcm_dummy() init
> [ 2.748352] omap_mcpdm_dummy() init
> [ 2.752960] aess aess: ABE Firmware version 9560
> [ 2.760162] omap_sr_disable: omap_sr struct for sr_iva not found
> [ 2.774414] mmc0: host does not support reading read-only switch. assuming write-enable.
> [ 2.785217] mmc0: new high speed SD card at address b368
> [ 2.791931] mmcblk0: mmc0:b368 E1213 976 MiB
> [ 2.798431] mmcblk0: p1 p2
> [ 2.799438] omap_sr_disable: omap_sr struct for sr_iva not found
> [ 2.811248] asoc: snd-soc-dummy-dai <-> MultiMedia1 mapping ok
> [ 2.819244] asoc: snd-soc-dummy-dai <-> MultiMedia2 mapping ok
> [ 2.828399] asoc: snd-soc-dummy-dai <-> Voice mapping ok
> [ 2.836395] asoc: snd-soc-dummy-dai <-> Tones mapping ok
> [ 2.843658] asoc: snd-soc-dummy-dai <-> Vibra mapping ok
> [ 2.849822] asoc: snd-soc-dummy-dai <-> MODEM mapping ok
> [ 2.855926] asoc: snd-soc-dummy-dai <-> MultiMedia1 LP mapping ok
> [ 2.862640] asoc: snd-soc-dummy-dai <-> omap-mcbsp.2 mapping ok
> [ 2.871795] asoc: twl6040-legacy <-> mcpdm-legacy mapping ok
> [ 2.878601] asoc: twl6040-dl1 <-> mcpdm-dl1 mapping ok
> [ 2.884338] asoc: twl6040-ul <-> mcpdm-ul1 mapping ok
> [ 2.890014] asoc: twl6040-dl2 <-> mcpdm-dl2 mapping ok
> [ 2.895782] asoc: twl6040-vib <-> mcpdm-vib mapping ok
> [ 2.901489] asoc: snd-soc-dummy-dai <-> omap-mcbsp.1 mapping ok
> [ 2.908050] asoc: snd-soc-dummy-dai <-> omap-mcbsp.1 mapping ok
> [ 2.914672] asoc: snd-soc-dummy-dai <-> omap-mcbsp.2 mapping ok
> [ 2.921295] usb 1-1.1: new high-speed USB device number 3 using ehci-omap
> [ 2.928680] asoc: snd-soc-dummy-dai <-> omap-mcbsp.2 mapping ok
> [ 2.936370] input: Panda Headset Jack as /devices/platform/omap-abe-twl6040/sound/card0/input0
> [ 2.950714] asoc: omap-hdmi-hifi <-> omap-hdmi-audio-dai mapping ok
> [ 2.958496] u32 classifier
> [ 2.961364] Actions configured
> [ 2.965362] TCP: cubic registered
> [ 2.969390] NET: Registered protocol family 10
> [ 2.975006] NET: Registered protocol family 17
> [ 2.979888] lib80211: common routines for IEEE802.11 drivers
> [ 2.986083] Registering the dns_resolver key type
> [ 2.991271] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 1
> [ 2.999420] ThumbEE CPU extension supported.
> [ 3.003997] Registering SWP/SWPB emulation handler
>
> _______________________________________________
> meta-ti mailing list
> meta-ti at yoctoproject.org
> https://lists.yoctoproject.org/listinfo/meta-ti
More information about the meta-ti
mailing list