[linux-yocto] [diff] Routerstation Pro console
michel.thebeau at windriver.com
michel.thebeau at windriver.com
Mon Apr 22 08:49:49 PDT 2013
---
--- /folk/mthebeau/tmp/rsp-console-v34.txt 2013-04-22 11:12:29.990716000 -0400
+++ /folk/mthebeau/tmp/rsp-console-v38.txt 2013-04-22 11:12:34.842739000 -0400
@@ -2,17 +2,13 @@
IP: 128.224.146.59/255.255.254.0, Gateway: 128.224.146.1
Default server: 128.224.149.6
RedBoot> ping -h 128.224.146.1
-PING: Cannot reach server '128.224.146.1' (128.224.146.1)
-RedBoot> ping -h 128.224.146.1
-PING: Cannot reach server '128.224.146.1' (128.224.146.1)
-RedBoot> ping -h 128.224.146.1
Network PING - from 128.224.146.59 to 128.224.146.1
PING - received 10 of 10 expected
-RedBoot> load -m tftp -h 128.224.149.6 mthebeau/vmlinux
-Entry point: 0x806a5430, address range: 0x80060000-0x808527d0
+RedBoot> load -m tftp -h 128.224.149.6 mthebeau/vmlinux.noftrace
+Entry point: 0x805cd4b0, address range: 0x80060000-0x8072d1fc
RedBoot> exec -c "console=ttyS0,115200 root=/dev/sda1 rw rootdelay=2 board=UBNT-RSPRO"
Now booting linux kernel:
- Base address 0x80050000 Entry 0x806a5430
+ Base address 0x80050000 Entry 0x805cd4b0
Cmdline : console=ttyS0,115200 root=/dev/sda1 rw rootdelay=2 board=UBNT-RSPRO
memsize=0x08000000
modetty0=0,n,8,1,hw
@@ -20,7 +16,7 @@
ethaddr=00.15.6d.c5.c3.ad
Initializing cgroup subsys cpuset
Initializing cgroup subsys cpu
-Linux version 3.4.36-yocto-standard (mitch at yow-mthebeau-lx2) (gcc version 4.7.2 (GCC) ) #1 PREEMPT Tue Apr 9 11:18:45 EDT 2013
+Linux version 3.8.4-yocto-standard (mitch at yow-mthebeau-lx2) (gcc version 4.7.2 (GCC) ) #2 PREEMPT Wed Apr 17 13:39:46 EDT 2013
bootconsole [early0] enabled
CPU revision is: 00019374 (MIPS 24Kc)
SoC: Atheros AR7161 rev 2
@@ -28,23 +24,24 @@
Determined physical RAM map:
memory: 08000000 @ 00000000 (usable)
Initrd not found or empty - disabling initrd
-Zone PFN ranges:
- Normal 0x00000000 -> 0x00008000
-Movable zone start PFN for each node
-Early memory PFN ranges
- 0: 0x00000000 -> 0x00008000
+Zone ranges:
+ Normal [mem 0x00000000-0x07ffffff]
+Movable zone start for each node
+Early memory node ranges
+ node 0: [mem 0x00000000-0x07ffffff]
+Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
+Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512
Kernel command line: console=ttyS0,115200 root=/dev/sda1 rw rootdelay=2 board=UBNT-RSPRO ethaddr=00.15.6d.c5.c3.ad
PID hash table entries: 512 (order: -1, 2048 bytes)
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
-Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
-Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
+__ex_table already sorted, skipping sort
Writing ErrCtl register=00006002
Readback ErrCtl register=00006002
allocated 262144 bytes of page_cgroup
please try 'cgroup_disable=memory' option if you don't want memory cgroups
-Memory: 120408k/131072k available (6514k kernel code, 10664k reserved, 1281k data, 344k init, 0k highmem)
+Memory: 121736k/131072k available (5617k kernel code, 9336k reserved, 1114k data, 244k init, 0k highmem)
SLUB: Genslabs=9, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
NR_IRQS:48
Calibrating delay loop... 479.23 BogoMIPS (lpj=2396160)
@@ -58,10 +55,8 @@
Initializing cgroup subsys freezer
Initializing cgroup subsys net_cls
Initializing cgroup subsys blkio
-ftrace: allocating 18218 entries in 36 pages
devtmpfs: initialized
NET: Registered protocol family 16
-gpiochip_add: registered GPIOs 0 to 15 on device: ath79
MIPS: machine is Ubiquiti RouterStation Pro
registering PCI controller with io_map_base unset
bio: create slab <bio-0> at 0
@@ -73,12 +68,12 @@
PCI host bridge to bus 0000:00
pci_bus 0000:00: root bus resource [mem 0x10000000-0x16ffffff]
pci_bus 0000:00: root bus resource [io 0x0000]
+pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
Switching to clocksource MIPS
NET: Registered protocol family 2
-IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
-TCP established hash table entries: 4096 (order: 3, 32768 bytes)
-TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
-TCP: Hash tables configured (established 4096 bind 4096)
+TCP established hash table entries: 1024 (order: 1, 8192 bytes)
+TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
+TCP: Hash tables configured (established 1024 bind 1024)
TCP: reno registered
UDP hash table entries: 256 (order: 0, 4096 bytes)
UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
@@ -88,12 +83,13 @@
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
squashfs: version 4.0 (2009/01/31) Phillip Lougher
-Registering unionfs 2.5.11 (for 3.3.0-rc3)
NFS: Registering the id_resolver key type
+Key type id_resolver registered
+Key type id_legacy registered
jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
Btrfs loaded
-msgmni has been set to 235
-Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
+msgmni has been set to 237
+Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
@@ -113,15 +109,17 @@
0x000000030000-0x000000270000 : "kernel-sda1"
0x000000ff0000-0x000000fff000 : "FIS directory"
0x000000fff000-0x000001000000 : "RedBoot config"
-ag71xx_mdio: probed
+libphy: ag71xx_mdio: probed
eth0: Atheros AG71xx at 0xb9000000, irq 4
-ag71xx ag71xx.0: eth0: connected to PHY at ag71xx-mdio.0:04 [uid=004dd041, driver=Atheros AR8216/AR8236/AR8316]
+ag71xx ag71xx.0 eth0: connected to PHY at ag71xx-mdio.0:04 [uid=004dd041, driver=Atheros AR8216/AR8236/AR8316]
eth1: Atheros AG71xx at 0xba000000, irq 5
eth1: Atheros AR8316 switch driver attached.
ar8316: Using port 4 as PHY
-ag71xx ag71xx.1: eth1: connected to PHY at ag71xx-mdio.0:00 [uid=004dd041, driver=Atheros AR8216/AR8236/AR8316]
+ag71xx ag71xx.1 eth1: connected to PHY at ag71xx-mdio.0:00 [uid=004dd041, driver=Atheros AR8216/AR8236/AR8316]
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
-ehci-platform ehci-platform: Generic Platform EHCI Controller
+ehci-pci: EHCI PCI platform driver
+ehci-platform: EHCI generic platform driver
+ehci-platform ehci-platform: EHCI Host Controller
ehci-platform ehci-platform: new USB bus registered, assigned bus number 1
ehci-platform ehci-platform: irq 3, io mem 0x1b000000
ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00
@@ -137,20 +135,19 @@
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
i8042: i8042 controller selftest timeout
-Trying to free nonexistent resource <0000000000000060-000000000000006f>
md: linear personality registered for level -1
md: raid0 personality registered for level 0
md: raid1 personality registered for level 1
md: raid10 personality registered for level 10
md: multipath personality registered for level -4
md: faulty personality registered for level -5
-device-mapper: ioctl: 4.22.0-ioctl (2011-10-19) initialised: dm-devel at redhat.com
+device-mapper: ioctl: 4.23.1-ioctl (2012-12-18) initialised: dm-devel at redhat.com
oprofile: using mips/24K performance monitoring.
TCP: cubic registered
NET: Registered protocol family 10
-IPv6 over IPv4 tunneling driver
+sit: IPv6 over IPv4 tunneling driver
NET: Registered protocol family 17
-Registering the dns_resolver key type
+Key type dns_resolver registered
console [netcon0] enabled
netconsole: network logging started
Waiting 2sec before mounting root device...
@@ -185,13 +182,13 @@
EXT3-fs (sda1): mounted filesystem with ordered data mode
VFS: Mounted root (ext3 filesystem) on device 8:1.
devtmpfs: mounted
-Freeing unused kernel memory: 344k freed
+Freeing unused kernel memory: 244k freed
Algorithmics/MIPS FPU Emulator v1.5
INIT: version 2.88 booting
Error Cannot open /dev/tty0: No such file or directory
Error opening /dev/fb0: No such file or directory
Starting Bootlog daemon: bootlogd.
-Configuring network interfaces... ADDRCONF(NETDEV_UP): eth0: link is not ready
+Configuring network interfaces... IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
udhcpc (v1.20.2) started
Sending discover...
Sending discover...
@@ -201,10 +198,8 @@
net.ipv4.conf.default.rp_filter = 1
net.ipv4.conf.all.rp_filter = 1
hwclock: can't open '/dev/misc/rtc': No such file or directory
-Tue Apr 9 16:08:00 UTC 2013
+Wed Apr 17 16:02:00 UTC 2013
hwclock: can't open '/dev/misc/rtc': No such file or directory
-Running postinst /etc/rpm-postinsts/rpm-postinsts...
-ERROR: postinst /etc/rpm-postinsts/rpm-postinsts failed.
Starting atd: OK
INIT: Entering runlevel: 5
Starting system message bus: dbus.
@@ -216,14 +211,11 @@
starting mountd: done
starting statd: done
Starting OpenBSD Secure Shell server: sshd
- generating ssh RSA key...
- generating ssh ECDSA key...
- generating ssh DSA key...
done.
Starting system log daemon...0
Starting kernel log daemon...0
Starting udev
-udevd[454]: starting version 182
+udevd[236]: starting version 182
Starting Lighttpd Web Server: lighttpd.
Starting crond: OK
Stopping Bootlog daemon: bootlogd.
@@ -234,18 +226,18 @@
root at routerstationpro:~# cat /proc/cmdline
console=ttyS0,115200 root=/dev/sda1 rw rootdelay=2 board=UBNT-RSPRO ethaddr=00.15.6d.c5.c3.ad
root at routerstationpro:~# uname -a
-Linux routerstationpro 3.4.36-yocto-standard #1 PREEMPT Tue Apr 9 11:18:45 EDT 2013 mips GNU/Linux
+Linux routerstationpro 3.8.4-yocto-standard #2 PREEMPT Wed Apr 17 13:39:46 EDT 2013 mips GNU/Linux
root at routerstationpro:~# poweroff
-Broadcast message from root at routerstationpro (ttyS0) (Tue Apr 9 16:08:57 201
The system is going down for system halt NOW!
-
INIT: Switching to run
INIT: Sending processes the TERM signal
+Broadcast message from root at routerstationpro (ttyS0) (Wed Apr 17 16:02:35 201
The system is going down for system halt NOW!
+
INIT:
INIT: Sending processes the TERM signal
root at routerstationpro:~#
INIT: SeStopping system message bus: hwclock: can't open '/dev/misc/rtc': No such file or directory
stopping statd: done
stopping mountd: done
stopping nfsd: done
Error unable to find a free virtual terminal: Inappropriate ioctl for device
Error opening /dev/fb0: No such file or directory
-Stopping OpenBSD Secure Shell server: sshdstopped /usr/sbin/sshd (pid 436)
+Stopping OpenBSD Secure Shell server: sshdstopped /usr/sbin/sshd (pid 218)
.
Stopping system log daemon...0
Stopping kernel log daemon...0
@@ -253,7 +245,7 @@
Deconfiguring network interfaces... ifdown: interface eth0 not configured
done.
Stopping crond: OK
-Stopping Lighttpd Web Server: stopped /usr/sbin/lighttpd (pid 691)
+Stopping Lighttpd Web Server: stopped /usr/sbin/lighttpd (pid 478)
lighttpd.
Sending all processes the TERM signal...
Sending all processes the KILL signal...
More information about the linux-yocto
mailing list