[yocto] meta-raspberry build fails with either VLC or FireFire.

[Edward Vidal]

Hi All,
My earlier build included VLC and FireFox.
meta-yocto-bsp    = "fido:0f8d89ce66cfffccc9911d6c61470a585173b79d"
meta-raspberrypi  = "master:7457bf182c8fd550ec877ecd786a3edd16e65495"
meta-oe           
meta-python       
meta-multimedia   
meta-gnome        = "fido:0f8d89ce66cfffccc9911d6c61470a585173b79d"

These were pulled a day ago.
I upgraded to the following and now VLC & FireFox causes errors
meta-yocto-bsp    = "master:dd282d475cb4fde4f4e6fd7afe437dc001584587"
meta-raspberrypi  = "master:f2cff839f52a6e6211337fc45c7c3eabf0fac113"
meta-oe           
meta-python       
meta-multimedia   
meta-gnome        = "master:dd282d475cb4fde4f4e6fd7afe437dc001584587"
meta-browser      = "master:ca96f4326345dcd779fc539877a04f069f431749"

Since VLC & FireFox depend on gtk+3-3.18.2 In the above repos.  
They fail in do_configure when I add to IMAGE_INSTALL_append 
in my local.conf file.

These are the what I added in added local.conf

#MACHINE ??= "qemux86"
ENABLE_SPI_BUS = "1"
MACHINE ??= "raspberrypi2"
GPU_MEM = "16"
PREFERRED_PROVIDER_virtual/egl ?= "vc-graphics-hardfp"
PREFERRED_PROVIDER_virtual/libgles2 ?= "vc-graphics-hardfp"
PREFERRED_PROVIDER_jpeg = "libjpeg-turbo"
PREFERRED_PROVIDER_jpeg-native = "libjpeg-turbo-native"
#adding the XSTOOLs depends
IMAGE_INSTALL_append = " xterm git \
 intelhex python-bitstring pyusb PyPubSub xstools   \
 chkconfig v4l-utils python-imaging socat lame  \
 linux-firmware jasper gsl  hexedit man iproute2 \
 gperf tree cmake tar pv openjpeg squashfs-tools \
 rsync yasm  gparted  tcl tk rpi-gpio geany python-pip iputils \
 opencv opencv-samples opencv-apps python-opencv devmem2 \
"

#DL_DIR ?= "${TOPDIR}/downloads"
DL_DIR ?= "/home/vidal/wkg/yocto/kernel_test/downloads"

EXTRA_IMAGE_FEATURES = "debug-tweaks dev-pkgs tools-sdk doc-pkgs qt4-pkgs"

This what is in bblayers.conf

# LAYER_CONF_VERSION is increased each time build/conf/bblayers.conf
# changes incompatibly
LCONF_VERSION = "6"

BBPATH = "${TOPDIR}"
BBFILES ?= ""

BBLAYERS ?= " \
  /home/vidal/wkg/yocto/kernel_test/poky/meta \
  /home/vidal/wkg/yocto/kernel_test/poky/meta-yocto \
  /home/vidal/wkg/yocto/kernel_test/poky/meta-yocto-bsp \
  /home/vidal/wkg/yocto/kernel_test/poky/meta-raspberrypi \
  /home/vidal/wkg/yocto/kernel_test/poky/meta-oe \
  /home/vidal/wkg/yocto/kernel_test/poky/meta-python \
  /home/vidal/wkg/yocto/kernel_test/poky/meta-multimedia \
  /home/vidal/wkg/yocto/kernel_test/poky/meta-gnome \
  /home/vidal/wkg/yocto/kernel_test/poky/meta-browser \
  "
BBLAYERS_NON_REMOVABLE ?= " \
  /home/vidal/wkg/yocto/kernel_test/poky/meta \
  /home/vidal/wkg/yocto/kernel_test/poky/meta-yocto \
  "
Any and all help is appreciated.

This is the goal of the build.

Transferred to my google dropbox core-image-sato120815.zip
If you do not access let me know and I will add you to share list.

The sha1sum should be the following:
12dc5b4e9cb737696b71c6502ffd095f5a896720  core-image-sato120815.zip
In the file sha1sum.txt

1.4 GB (1,449,293,907 bytes)

This is what I used to transfer to a micro SD card.

"gzip -dc /home/vidal/wkg/yocto/core-image-sato120815.zip | pv | dd bs=16M of=/dev/sdb"
3.64GB 0:08:01 [7.74MB/s]
The root passwd is raspberrypi

This will fit on 4GB micro SD card.

Provides the Linux 4.1.10 Kernel, git, gcc-5.2.0, OpenCV, Myhdl, Iverilog, 
gsl, yosys, arachne-pnr, CAT-Board, rhea, Xstools and Gtkwave.  

CAT-Board Features

* Lattice iCE40-HX8K FPGA in 256-pin BGA.
* 32 MByte SDRAM (16M x 16).
* Serial configuration flash (at least 2 Mbit).
* Three Grove connectors.
* Two PMOD connectors.
* One 20x2 header with 3.3V, ground and 18 FPGA I/Os.
* Two SATA headers (for differential signals; don't know if they would work with SATA HDDs.)
* DIP switch with four SPST switches.
* Two momentary pushbuttons.
* Four LEDs.
* 100 MHz oscillator.
* 5.0 V jack for external power supply.
* 3.3 V and 1.2 V regulators.
* Adjustable voltage on one bank of FPGA I/O pins.
* 32 KByte HAT EEPROM.
* 40-pin RPi GPIO header.

See Driving an Array of LED Digits with the CAT Board at
https://hackaday.io/project/7982-cat-board.  

The prototype has been tested with Yocto & RaspBian on RPi2B.
With these tools, this combo is a complete development system, to develop, test and program
 FPGA applications completly on the RPi2B and CAT-Board.

The schematic is available at
https://raw.githubusercontent.com/xesscorp/CAT-Board/master/docs/Manual/pics/CAT_schematic.pdf

This should be around the cost as the StickIt-MB & XulA2-LX9.  Dave will be finalizing the price soon.

The led digit provides a good method to test the CAT-Board and RPi2B.


see xess.com

Cheers, 
 Edward Vidal Jr. e-mail develone at sbcglobal.net 915-595-1613
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.yoctoproject.org/pipermail/yocto/attachments/20151209/9eb03eea/attachment.html>