[meta-freescale] [PATCH 1/3][meta-fsl-arm-extra] bcm4330-nvram-config: Add imx6sl-warp support

[Fabio Estevam]

The imx6sl-warp board has a bcm4330 chip, so enable the nvram
configuration to allow the WiFi to work out of box.

Signed-off-by: Fabio Estevam <fabio.estevam at freescale.com>
---
 .../broadcom-nvram-config/bcm4330-nvram-config.bb  |   2 +-
 .../files/imx6sl-warp/brcmfmac4330-sdio.txt        | 118 +++++++++++++++++++++
 2 files changed, 119 insertions(+), 1 deletion(-)
 create mode 100644 recipes-bsp/broadcom-nvram-config/files/imx6sl-warp/brcmfmac4330-sdio.txt

diff --git a/recipes-bsp/broadcom-nvram-config/bcm4330-nvram-config.bb b/recipes-bsp/broadcom-nvram-config/bcm4330-nvram-config.bb
index 2875199..5512b2d 100644
--- a/recipes-bsp/broadcom-nvram-config/bcm4330-nvram-config.bb
+++ b/recipes-bsp/broadcom-nvram-config/bcm4330-nvram-config.bb
@@ -5,4 +5,4 @@ include broadcom-nvram-config.inc
 
 CHIP_MODEL = "4330"
 
-COMPATIBLE_MACHINE = "(cubox-i|nitrogen6x-lite|wandboard-dual|wandboard-quad)"
+COMPATIBLE_MACHINE = "(cubox-i|nitrogen6x-lite|wandboard-dual|wandboard-quad|imx6sl-warp)"
diff --git a/recipes-bsp/broadcom-nvram-config/files/imx6sl-warp/brcmfmac4330-sdio.txt b/recipes-bsp/broadcom-nvram-config/files/imx6sl-warp/brcmfmac4330-sdio.txt
new file mode 100644
index 0000000..09a044f
--- /dev/null
+++ b/recipes-bsp/broadcom-nvram-config/files/imx6sl-warp/brcmfmac4330-sdio.txt
@@ -0,0 +1,118 @@
+manfid=0x2d0
+prodid=0x0532
+vendid=0x14e4
+devid=0x4360
+boardtype=0x0532
+boardrev=0x20
+boardflags=0x10080201
+
+nocrc=1
+xtalfreq=37400
+xtalmode=0x20,0x4,0
+boardnum=22
+macaddr=00:90:4c:c5:12:38
+ag0=252
+ag1=252
+aa2g=1
+aa5g=1
+ccode=EU
+regrev=5
+
+#for BT-coexistence
+btc_params80=0
+btc_params6=10
+btc_params8=10000
+
+sd_gpout=0
+# sd_oobonly=1
+muxenab=0x10
+
+# 2G PA param_B42R 110927
+pa0b0=0x12E4
+pa0b1=0xFE09
+pa0b2=0xFF9A
+#pa0itssit=62
+rssismf2g=0xa
+rssismc2g=0x3
+rssisav2g=0x7
+
+# rssi params for 5GHz B42R_110803
+#rssismf5g=0x4
+rssismf5g=0xa
+rssismc5g=0x7
+rssisav5g=0x1
+#PA parameters for lower band
+pa1lob0=0x144F
+pa1lob1=0xFD6B
+pa1lob2=0xFF3B
+#PA parameters for midband
+pa1b0=0x139C
+pa1b1=0xFD87
+pa1b2=0xFF4F
+#PA parameters for high band
+pa1hib0=0x12CA
+pa1hib1=0xFD9A
+pa1hib2=0xFF4E
+
+# 2G PA offset
+maxp2ga0=64
+sromrev=3
+cckpo=0
+ofdm2gpo=0x66666666
+mcs2gpo0=0xaaaa
+mcs2gpo1=0xaaaa
+
+# 5G PA offset
+maxp5ga0=66
+maxp5gla0=66
+maxp5gha0=66
+ofdm5gpo=0x22222222
+ofdm5glpo=0x11111111
+ofdm5ghpo=0x22222222
+mcs5gpo0=0x6666
+mcs5gpo1=0x6666
+mcs5glpo0=0x5555
+mcs5glpo1=0x5555
+mcs5ghpo0=0x6666
+mcs5ghpo1=0x6666
+
+cckPwrOffset=4
+cckdigfilttype=22
+ofdmdigfilttype=2
+extpagain5g=2
+#wl0id=0x431b
+
+# For 2GHz Tx EVM/SM
+rfreg033=0x19
+rfreg033_cck=0x1d
+pacalidx2g=65
+dacrate2g=160
+txalpfbyp2g=1
+bphyscale=17
+
+# 5GHz LOFT and IQ CAL
+txgaintbl5g=1
+txiqlopapu5g=1
+txiqlopag5g=0x10
+iqlocalidx5g=24
+
+# 5GHz Noise CAL parameter
+noise_cal_po_5g=5
+noise_cal_enable_5g=0
+
+# 2GHz RxPER at low rates
+noise_cal_ref_2g=56
+noise_cal_po_bias_2g=-4
+noise_cal_enable_2g=1
+
+# Max input level on a-band
+triso5g=9
+
+# Tx power control, especially temp.
+tssitime=1
+
+#fc+1.7GHz Spur Elimination
+loidacmode5g=1
+
+swctrlmap_2g=0x84048404, 0x82028202, 0x84048404, 0x010202, 0x1ff
+swctrlmap_5g=0xC040C040, 0xB030A020, 0xA020C040, 0x010A02, 0x2F8
-- 
1.9.1