[meta-freescale] [meta-fsl-arm-extra][PATCH] broadcom-nvram-config: add cubox-i

[Carlos Rafael Giani]

Since I am not knowledgeable about the Broadcom hardware, I asked 
around. As a conclusion, it looks fine, except for two things:

* ccode=CN should use =ALL instead. This is the parameter that specifies 
which frequency spectrum to scan. The spectrum in EU and US are 
different than in CN. Perhaps this should be configurable.
* MACHINE_FIRMWARE_append_mx6 = " linux-firmware-ath6k" should be 
changed as well. Something like "linux-firmware-brcmfmac" would make 
more sense, if such a package exists.


On 2014-11-13 19:53, Benjamin Cohen wrote:
> - add bcm4330 nvram config for cubox-i
> - add bcm4330-nvram-config to MACHINE_EXTRA_RRECOMMENDS for cubox-i
>
> Signed-off-by: Benjamin Cohen <bencoh at notk.org>
> ---
>   conf/machine/cubox-i.conf                          |    4 ++
>   .../broadcom-nvram-config/bcm4330-nvram-config.bb  |    2 +-
>   .../files/cubox-i/brcmfmac4330-sdio.txt            |   40 ++++++++++++++++++++
>   3 files changed, 45 insertions(+), 1 deletion(-)
>   create mode 100644 recipes-bsp/broadcom-nvram-config/files/cubox-i/brcmfmac4330-sdio.txt
>
> diff --git a/conf/machine/cubox-i.conf b/conf/machine/cubox-i.conf
> index 6c67c19..fa90d7c 100644
> --- a/conf/machine/cubox-i.conf
> +++ b/conf/machine/cubox-i.conf
> @@ -33,4 +33,8 @@ KERNEL_DEVICETREE = "imx6dl-cubox-i.dtb imx6q-cubox-i.dtb imx6dl-hummingboard.dt
>   MACHINE_FEATURES += "pci wifi bluetooth alsa bluetooth irda serial usbhost wifi"
>   MACHINE_FIRMWARE_append_mx6 = " linux-firmware-ath6k"
>   
> +MACHINE_EXTRA_RRECOMMENDS += " \
> +	bcm4330-nvram-config \
> +"
> +
>   SERIAL_CONSOLE = "115200 ttymxc0"
> diff --git a/recipes-bsp/broadcom-nvram-config/bcm4330-nvram-config.bb b/recipes-bsp/broadcom-nvram-config/bcm4330-nvram-config.bb
> index 592cfc9..d5e7ebb 100644
> --- a/recipes-bsp/broadcom-nvram-config/bcm4330-nvram-config.bb
> +++ b/recipes-bsp/broadcom-nvram-config/bcm4330-nvram-config.bb
> @@ -5,4 +5,4 @@ include broadcom-nvram-config.inc
>   
>   CHIP_MODEL = "4330"
>   
> -COMPATIBLE_MACHINE = "(nitrogen6x-lite|wandboard-dual|wandboard-quad)"
> +COMPATIBLE_MACHINE = "(nitrogen6x-lite|wandboard-dual|wandboard-quad|cubox-i)"
> diff --git a/recipes-bsp/broadcom-nvram-config/files/cubox-i/brcmfmac4330-sdio.txt b/recipes-bsp/broadcom-nvram-config/files/cubox-i/brcmfmac4330-sdio.txt
> new file mode 100644
> index 0000000..9546246
> --- /dev/null
> +++ b/recipes-bsp/broadcom-nvram-config/files/cubox-i/brcmfmac4330-sdio.txt
> @@ -0,0 +1,40 @@
> +# bcm94330wlsdgb.txt
> +manfid=0x2d0
> +prodid=0x0552
> +vendid=0x14e4
> +devid=0x4360
> +boardtype=0x0552
> +boardrev=0x11
> +# this design has 2.4GHz SP3T switch
> +boardflags=0x00080200
> +nocrc=1
> +xtalfreq=37400
> +boardnum=22
> +macaddr=00:90:4c:c5:12:38
> +ag0=255
> +aa2g=1
> +ccode=CN
> +pa0b0=0x14d0
> +pa0b1=0xfd98
> +pa0b2=0xff78
> +rssismf2g=0xa
> +rssismc2g=0x3
> +rssisav2g=0x7
> +maxp2ga0=0x50
> +sromrev=3
> +il0macaddr=00:90:4c:c5:12:38
> +wl0id=0x431b
> +cckPwrOffset=5
> +ofdm2gpo=0x66666666
> +mcs2gpo0=0x6666
> +mcs2gpo1=0x6666
> +swctrlmap_2g=0x04040404,0x02020202,0x02020404,0x10202,0x1ff
> +swctrlmap_5g=0x00100010,0x00280020,0x00200010,0x14202,0x2f8
> +rfreg033=0x19
> +rfreg033_cck=0x1f
> +dacrate2g=160
> +txalpfbyp2g=1
> +bphyscale=17
> +cckPwrIdxCorr=-15
> +pacalidx2g=45
> +txgaintbl=1