[meta-freescale] i.MX28 SDCARD boot fail after dd Yocto fsl-image-gui-sdk image
ttom at ms5.url.com.tw
ttom at ms5.url.com.tw
Thu May 2 03:51:25 PDT 2013
Hi,
Afer use fsl-image-gui-sdk's sd card image, Then the SD Card can't replace fsl-image-gui and
fsl-image-test by dd.
DD command is "sudo dd if= <fsl-image-test-xxxxxx file>.sdcard of=/dev/sdX bs=4M"
Error message list below
Any way to solve this problem?
********************
U-Boot 2013.04 (Apr 29 2013 -
12:21:11)
CPU: Freescale i.MX28 rev1.2 at 454 MHz
BOOT: SSP SD/MMC #0, 3V3
DRAM: 128 MiB
NAND: No NAND device found!!!
0 MiB
MMC:
MXS MMC: 0
MMC0: Command 8 timeout (status 0xe0384020)
*** Warning - bad CRC, using
default environment
In:
serial
Out:
serial
Err:
serial
Net: FEC0
[PRIME]
Warning: FEC0 using MAC address from net
device
,
FEC1
Warning: FEC1 using MAC address from net
device
Hit any key to stop autoboot:
0
mmc0 is current
device
MMC0: Command 8 timeout (status
0xe02c4020)
reading
boot.scr
** Unable to read file boot.scr
**
reading
uImage
2601492 bytes read in 801 ms (3.1
MiB/s)
Booting from mmc
...
reading
imx28-evk.dtb
** Unable to read file imx28-evk.dtb
**
## Booting kernel from Legacy Image at 42000000
...
Image Name:
Linux-2.6.35.3-1.1.0+yocto+g9145
Created: 2013-04-29 3:46:03
UTC
Image Type: ARM Linux Kernel Image
(uncompressed)
Data Size: 2601428 Bytes = 2.5
MiB
Load Address:
40008000
Entry Point:
40008000
Verifying Checksum ...
OK
Loading Kernel Image ...
OK
OK
Starting kernel
...
Uncompressing Linux... done, booting the
kernel.
Linux version 2.6.35.3-1.1.0+yocto+g914558e (thomas at thomas-Linux) (gcc version 3
CPU: ARM926EJ-S [41069265] revision 5 (ARMv5TEJ),
cr=00053177
CPU: VIVT data cache, VIVT instruction
cache
Machine: Freescale MX28EVK
board
Memory policy: ECC disabled, Data cache
writeback
Built 1 zonelists in Zone order, mobility grouping on. Total pages:
32512
Kernel command line: console=ttyAMA0,115200
root=/dev/mmcblk0p3 rw rootwait
PID hash table entries: 512 (order:
-1, 2048
bytes)
Dentry cache hash table entries: 16384 (order: 4, 65536
bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768
bytes)
Memory: 128MB = 128MB
total
Memory: 124228k/124228k available, 6844k reserved, 0K
highmem
Virtual kernel memory
layout:
vector : 0xffff0000 - 0xffff1000 ( 4
kB)
fixmap : 0xfff00000 - 0xfffe0000 ( 896
kB)
DMA : 0xfde00000 - 0xffe00000
( 32
MB)
vmalloc : 0xc8800000 - 0xf0000000 ( 632
MB)
lowmem : 0xc0000000 - 0xc8000000 ( 128
MB)
modules : 0xbf000000 - 0xc0000000 ( 16
MB)
.init : 0xc0008000 - 0xc0030000 ( 160
kB)
.text : 0xc0030000 - 0xc050b000 (4972
kB)
.data : 0xc050c000 - 0xc054a4a0 ( 250
kB)
SLUB: Genslabs=11, HWalign=32, Order=0-3, MinObjects=0, CPUs=1,
Nodes=1
Hierarchical RCU
implementation.
RCU-based detection of stalled CPUs is
disabled.
Verbose stalled-CPUs detection is
disabled.
NR_IRQS:288
Console: colour dummy device
80x30
console [ttyAMA0]
enabled
Calibrating delay loop... 226.09 BogoMIPS
(lpj=1130496)
pid_max: default: 32768 minimum:
301
Security Framework
initialized
SELinux:
Initializing.
Mount-cache hash table entries:
512
CPU: Testing write buffer coherency:
ok
devtmpfs:
initialized
regulator: core version
0.5
NET: Registered protocol family
16
regulator: vddd: 800 <--> 1575 mV at 1500 mV fast
normal
regulator: vdddbo: 800 <--> 1575 mV fast
normal
regulator: vdda: 1500 <--> 2275 mV at 1800 mV fast
normal
vddio = 3380000,
val=10
regulator: vddio: 2880 <--> 3680 mV at 3380 mV fast
normal
regulator: overall_current: fast
normal
regulator:
vbus5v:
regulator: mxs-duart-1: fast
normal
regulator: mxs-bl-1: fast
normal
regulator: mxs-i2c-1: fast
normal
regulator: mmc_ssp-1: fast
normal
regulator: mmc_ssp-2: fast
normal
regulator: charger-1: fast
normal
regulator: power-test-1: fast
normal
regulator: cpufreq-1: fast
normal
i.MX IRAM pool: 124
KB at 0xc8820000
usb DR wakeup device is
registered
IMX usb wakeup
probe
audit: cannot initialize inotify
handle
bio: create slab <bio-0> at
0
SCSI subsystem
initialized
Freescale USB OTG Driver loaded, $Revision: 1.55
$
usbcore: registered new interface driver
usbfs
usbcore: registered new interface driver
hub
usbcore: registered new device driver
usb
Advanced Linux Sound Architecture Driver Version
1.0.23.
Switching to clocksource mxs clock
source
NET: Registered protocol family
2
IP route cache hash table entries: 1024 (order: 0, 4096
bytes)
TCP established hash table entries: 4096 (order: 3, 32768
bytes)
TCP bind hash table entries: 4096 (order: 2, 16384
bytes)
TCP: Hash tables configured (established 4096 bind
4096)
TCP reno
registered
UDP hash table entries: 256 (order: 0, 4096
bytes)
UDP-Lite hash table entries: 256 (order: 0, 4096
bytes)
NET: Registered protocol family
1
RPC: Registered udp transport
module.
RPC: Registered tcp transport
module.
RPC: Registered tcp NFSv4.1 backchannel transport
module.
Bus freq driver module
loaded
IMX usb wakeup
probe
usb h1 wakeup device is
registered
mxs_cpu_init: cpufreq init
finished
audit: initializing netlink socket
(disabled)
type=2000 audit(0.490:1):
initialized
VFS: Disk quotas
dquot_6.5.2
Dquot-cache hash table entries: 1024 (order 0, 4096
bytes)
JFFS2 version 2.2. (NAND) �© 2001-2006 Red Hat,
Inc.
msgmni has been set to
242
alg: No test for stdrng
(krng)
cryptodev: driver
loaded.
Block layer SCSI generic (bsg) driver version 0.4 loaded (major
253)
io scheduler noop
registered
io scheduler deadline
registered
io scheduler cfq registered
(default)
Console: switching to colour frame buffer device
100x30
mxs-duart.0: ttyAMA0 at MMIO 0x80074000 (irq = 47) is a
DebugUART
mxs-auart.0: ttySP0 at MMIO 0x8006a000 (irq = 112) is a
mxs-auart.0
Found
APPUART
3.1.0
mxs-auart.1: ttySP1 at MMIO 0x8006c000 (irq = 113) is a
mxs-auart.1
Found
APPUART
3.1.0
mxs-auart.2: ttySP2 at MMIO 0x8006e000 (irq = 114) is a
mxs-auart.2
Found
APPUART
3.1.0
mxs-auart.3: ttySP3 at MMIO 0x80070000 (irq = 115) is a
mxs-auart.3
Found
APPUART
3.1.0
mxs-auart.4: ttySP4 at MMIO 0x80072000 (irq = 116) is a
mxs-auart.4
Found
APPUART
3.1.0
brd: module
loaded
loop: module
loaded
i.MX GPMI
NFC
NFC: Version 1, 8-chip GPMI and
BCH
gpmi-nfc: probe of gpmi-nfc.0 failed with error
1
mxs-spi mxs-spi.0: Max possible speed 120000 = 120000000/2
kHz
mxs-spi mxs-spi.0: at 0x80014000 mapped to 0xF0014000, irq=84, bus 1, DMA ver_m4
FEC Ethernet
Driver
fec_enet_mii_bus:
probed
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI)
Driver
fsl-ehci fsl-ehci: Freescale On-Chip EHCI Host
Controller
fsl-ehci fsl-ehci: new USB bus registered, assigned bus number
1
fsl-ehci fsl-ehci: irq 93, io base
0x80080000
fsl-ehci fsl-ehci: USB 2.0 started, EHCI
1.00
hub 1-0:1.0: USB hub
found
hub 1-0:1.0: 1 port
detected
fsl-ehci fsl-ehci.0: Freescale On-Chip EHCI Host
Controller
fsl-ehci fsl-ehci.0: new USB bus registered, assigned bus number
2
fsl-ehci
fsl-ehci.0: irq 92, io base
0x80090000
fsl-ehci fsl-ehci.0: USB 2.0 started, EHCI
1.00
hub 2-0:1.0: USB hub
found
hub 2-0:1.0: 1 port
detected
Initializing USB Mass Storage
driver...
usbcore: registered new interface driver
usb-storage
USB Mass Storage support
registered.
ARC USBOTG Device Controller driver (1 August
2005)
mice: PS/2 mouse device common for all
mice
input: mxs-kbd as
/devices/platform/mxs-kbd.0/input/input0
input: MXS touchscreen as
/devices/virtual/input/input1
MXS RTC driver v1.0 hardware
v2.3.0
mxs-rtc mxs-rtc.0: rtc core: registered mxs-rtc as
rtc0
IR NEC protocol handler
initialized
IR RC5(x) protocol handler
initialized
IR RC6 protocol handler
initialized
IR JVC protocol handler
initialized
IR Sony protocol handler
initialized
Linux video capture interface:
v2.00
mxs-pxp mxs-pxp.0:
initialized
mxs watchdog: initialized, heartbeat 19
sec
mxs-mmc: MXS SSP Controller MMC Interface
driver
mxs-mmc mxs-mmc.0: mmc0: MXS SSP MMC DMAIRQ 82 ERRIRQ
96
dcp dcp.0: DCP crypto
enabled.!
usbcore: registered new interface driver
hiddev
usbcore: registered new interface driver
usbhid
usbhid: USB HID core
driver
sgtl5000-i2c 0-000a: SGTL5000 revision
17
mmc0: new high speed SD card at address
0002
mmcblk0: mmc0:0002 N/A 3.67 GiB
(ro)
mmcblk0: p1 p2
p3
mxs-spdif mxs-spdif.0: MXS SPDIF Audio
Transmitter
No device for codec mxs
spdif
No device for DAI mxs
spdif
No device for DAI
mxs-saif
No device for DAI
mxs-spdif
asoc: SGTL5000 <-> mxs-saif mapping
ok
Failed to add route LINE_OUT->Ext
Spk
asoc: mxs spdif <-> mxs-spdif mapping
ok
ALSA device
list:
#0: mxs-evk
(SGTL5000)
#1: mxs-evk (mxs
spdif)
TCP cubic
registered
NET: Registered protocol family
17
can: controller area network core (rev 20090105 abi
8)
NET: Registered protocol family
29
can: raw protocol (rev
20090105)
mxs-rtc mxs-rtc.0: setting system clock to 1970-01-01 00:00:06 UTC
(6)
VFS: Cannot open root device
"mmcblk0p3" or
unknown-block(179,3)
Please append a correct "root=" boot option; here are the available partitions:
b300 3850240 mmcblk0 driver:
mmcblk
b301 1024
mmcblk0p1
b302 10240
mmcblk0p2
b303 372736
mmcblk0p3
Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(179,3)
Backtrace:
[<c0034110>] (dump_backtrace+0x0/0x10c) from [<c03d2364>]
(dump_stack+0x18/0x1c)
r6:c0029a14 r5:c7471000 r4:c054b3f8
r3:00000002
[<c03d234c>] (dump_stack+0x0/0x1c) from [<c03d254c>]
(panic+0x74/0xf0)
[<c03d24d8>]
(panic+0x0/0xf0) from [<c0008f14>] (mount_block_root+0x1d4/0x218)
r3:00000000 r2:00000001 r1:c7c27f48
r0:c048cdf4
[<c0008d40>] (mount_block_root+0x0/0x218) from [<c0009130>]
(mount_root+0xe0/0x)
[<c0009050>] (mount_root+0x0/0x124) from [<c00092e0>]
(prepare_namespace+0x16c/)
r5:c0029a29
r4:c054a758
[<c0009174>] (prepare_namespace+0x0/0x1cc) from [<c0008b14>]
(kernel_init+0x12c)
r5:c0028600
r4:c0028600
[<c00089e8>] (kernel_init+0x0/0x16c) from [<c004f490>]
(do_exit+0x0/0x6c0)
r5:c00089e8 r4:00000000
**************************
--
http://isp.url.com.tw
´¼¨¹¥Í¬¡À]§K¶O¼·±µ¤Wºô ¹q¸Ü 40661234 / 4497890 ±b¸¹ url ±K½X url
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.yoctoproject.org/pipermail/meta-freescale/attachments/20130502/a95b558e/attachment.html>
More information about the meta-freescale
mailing list