[meta-freescale] [meta-fsl-arm-extra][PATCH 1/3] Add kernel support for Wandboard Dual
Otavio Salvador
otavio at ossystems.com.br
Tue Feb 26 11:24:03 PST 2013
On Sat, Feb 23, 2013 at 5:29 PM, John Weber <rjohnweber at gmail.com> wrote:
> This patch adds kernel support for Wandboard Dual. It is meant
> to be over the 1.1.0 SDK kernel from Freescale.
>
> Signed-off-by: John Weber <rjohnweber at gmail.com>
Please change short log to:
linux (3.0.35): Add Wandboard Dual support
> Upstream-Status: Pending
This doesn't bellongs here but in the patch file itself... more bellow.
> .../Initial-kernel-support-for-Wandboard.patch | 3195 ++++++++++++++++++++
> .../linux-imx-3.0.35/wandboard-dual/defconfig | 2762 +++++++++++++++++
> recipes-kernel/linux/linux-imx_3.0.35.bbappend | 8 +
> 3 files changed, 5965 insertions(+)
> create mode 100644 recipes-kernel/linux/linux-imx-3.0.35/Initial-kernel-support-for-Wandboard.patch
Please move it inside wandboard-dual directory; if it will be shared
between both wandboard please move it inside wandboard and do the
override append (as did in olinuxino board).
> create mode 100644 recipes-kernel/linux/linux-imx-3.0.35/wandboard-dual/defconfig
> create mode 100644 recipes-kernel/linux/linux-imx_3.0.35.bbappend
>
> diff --git a/recipes-kernel/linux/linux-imx-3.0.35/Initial-kernel-support-for-Wandboard.patch b/recipes-kernel/linux/linux-imx-3.0.35/Initial-kernel-support-for-Wandboard.patch
> new file mode 100644
> index 0000000..5dfbc96
> --- /dev/null
> +++ b/recipes-kernel/linux/linux-imx-3.0.35/Initial-kernel-support-for-Wandboard.patch
> @@ -0,0 +1,3195 @@
> +From f82dfc918b80905559bc1b97877a88bd85ede40f Mon Sep 17 00:00:00 2001
> +From: John Weber <rjohnweber at gmail.com>
> +Date: Fri, 22 Feb 2013 01:12:20 -0600
> +Subject: [PATCH] Initial kernel support Wandboard
> +
> + This patch adds support for Wandboard. It depends on
> + the FSL SDK 1.1.0 kernel (3.0.35). It has been minimally
> + tested on a Wandboard-Dual, rev A0. The serial port and
> + module SD card were found to work. Testers welcome!
> +
> + Most of this was lifted and ported from the Wandboard SDK
> + released Feb 2, 2013. That original work was done by Tapani.
> +
Please add:
Upstream-Status: Pending
and also add your signed-off-by as you did the patch porting.
> +diff --git a/arch/arm/configs/wandboard_defconfig b/arch/arm/configs/wandboard_defconfig
> +new file mode 100644
> +index 0000000..da75924
> +--- /dev/null
> ++++ b/arch/arm/configs/wandboard_defconfig
> +@@ -0,0 +1,1976 @@
> ++#
> ++# Automatically generated make config: don't edit
> ++# Linux/arm 3.0.35 Kernel Configuration
> ++#
> ++CONFIG_ARM=y
> ++CONFIG_SYS_SUPPORTS_APM_EMULATION=y
> ++CONFIG_HAVE_SCHED_CLOCK=y
> ++CONFIG_GENERIC_GPIO=y
> ++# CONFIG_ARCH_USES_GETTIMEOFFSET is not set
> ++CONFIG_GENERIC_CLOCKEVENTS=y
> ++CONFIG_GENERIC_CLOCKEVENTS_BROADCAST=y
> ++CONFIG_KTIME_SCALAR=y
> ++CONFIG_HAVE_PROC_CPU=y
> ++CONFIG_STACKTRACE_SUPPORT=y
> ++CONFIG_LOCKDEP_SUPPORT=y
> ++CONFIG_TRACE_IRQFLAGS_SUPPORT=y
> ++CONFIG_HARDIRQS_SW_RESEND=y
> ++CONFIG_GENERIC_IRQ_PROBE=y
> ++CONFIG_GENERIC_LOCKBREAK=y
> ++CONFIG_RWSEM_GENERIC_SPINLOCK=y
> ++CONFIG_ARCH_HAS_CPUFREQ=y
> ++CONFIG_ARCH_HAS_CPU_IDLE_WAIT=y
> ++CONFIG_GENERIC_HWEIGHT=y
> ++CONFIG_GENERIC_CALIBRATE_DELAY=y
> ++CONFIG_NEED_DMA_MAP_STATE=y
> ++CONFIG_FIQ=y
> ++CONFIG_VECTORS_BASE=0xffff0000
> ++# CONFIG_ARM_PATCH_PHYS_VIRT is not set
> ++CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
> ++CONFIG_HAVE_IRQ_WORK=y
> ++
> ++#
> ++# General setup
> ++#
> ++CONFIG_EXPERIMENTAL=y
> ++CONFIG_INIT_ENV_ARG_LIMIT=32
> ++CONFIG_CROSS_COMPILE=""
> ++CONFIG_LOCALVERSION=""
> ++# CONFIG_LOCALVERSION_AUTO is not set
> ++CONFIG_HAVE_KERNEL_GZIP=y
> ++CONFIG_HAVE_KERNEL_LZMA=y
> ++CONFIG_HAVE_KERNEL_LZO=y
> ++# CONFIG_KERNEL_GZIP is not set
> ++CONFIG_KERNEL_LZMA=y
> ++# CONFIG_KERNEL_LZO is not set
> ++CONFIG_DEFAULT_HOSTNAME="wandboard"
> ++# CONFIG_SWAP is not set
> ++CONFIG_SYSVIPC=y
> ++CONFIG_SYSVIPC_SYSCTL=y
> ++# CONFIG_POSIX_MQUEUE is not set
> ++# CONFIG_BSD_PROCESS_ACCT is not set
> ++# CONFIG_FHANDLE is not set
> ++# CONFIG_TASKSTATS is not set
> ++# CONFIG_AUDIT is not set
> ++CONFIG_HAVE_GENERIC_HARDIRQS=y
> ++
> ++#
> ++# IRQ subsystem
> ++#
> ++CONFIG_GENERIC_HARDIRQS=y
> ++CONFIG_HAVE_SPARSE_IRQ=y
> ++CONFIG_GENERIC_IRQ_SHOW=y
> ++# CONFIG_SPARSE_IRQ is not set
> ++
> ++#
> ++# RCU Subsystem
> ++#
> ++CONFIG_TREE_PREEMPT_RCU=y
> ++CONFIG_PREEMPT_RCU=y
> ++# CONFIG_RCU_TRACE is not set
> ++CONFIG_RCU_FANOUT=32
> ++# CONFIG_RCU_FANOUT_EXACT is not set
> ++# CONFIG_TREE_RCU_TRACE is not set
> ++# CONFIG_RCU_BOOST is not set
> ++# CONFIG_IKCONFIG is not set
> ++CONFIG_LOG_BUF_SHIFT=14
> ++# CONFIG_CGROUPS is not set
> ++# CONFIG_NAMESPACES is not set
> ++# CONFIG_SCHED_AUTOGROUP is not set
> ++# CONFIG_SYSFS_DEPRECATED is not set
> ++# CONFIG_RELAY is not set
> ++# CONFIG_BLK_DEV_INITRD is not set
> ++CONFIG_CC_OPTIMIZE_FOR_SIZE=y
> ++CONFIG_SYSCTL=y
> ++CONFIG_ANON_INODES=y
> ++CONFIG_PANIC_TIMEOUT=0
> ++CONFIG_EXPERT=y
> ++CONFIG_UID16=y
> ++CONFIG_SYSCTL_SYSCALL=y
> ++CONFIG_KALLSYMS=y
> ++CONFIG_HOTPLUG=y
> ++CONFIG_PRINTK=y
> ++# CONFIG_BUG is not set
> ++# CONFIG_ELF_CORE is not set
> ++CONFIG_BASE_FULL=y
> ++CONFIG_FUTEX=y
> ++CONFIG_EPOLL=y
> ++CONFIG_SIGNALFD=y
> ++CONFIG_TIMERFD=y
> ++CONFIG_EVENTFD=y
> ++# CONFIG_SHMEM is not set
> ++# CONFIG_AIO is not set
> ++CONFIG_EMBEDDED=y
> ++CONFIG_HAVE_PERF_EVENTS=y
> ++CONFIG_PERF_USE_VMALLOC=y
> ++
> ++#
> ++# Kernel Performance Events And Counters
> ++#
> ++# CONFIG_PERF_EVENTS is not set
> ++# CONFIG_PERF_COUNTERS is not set
> ++# CONFIG_VM_EVENT_COUNTERS is not set
> ++# CONFIG_SLUB_DEBUG is not set
> ++CONFIG_COMPAT_BRK=y
> ++# CONFIG_SLAB is not set
> ++CONFIG_SLUB=y
> ++# CONFIG_SLOB is not set
> ++# CONFIG_PROFILING is not set
> ++CONFIG_HAVE_OPROFILE=y
> ++# CONFIG_KPROBES is not set
> ++CONFIG_HAVE_KPROBES=y
> ++CONFIG_HAVE_KRETPROBES=y
> ++CONFIG_USE_GENERIC_SMP_HELPERS=y
> ++CONFIG_HAVE_REGS_AND_STACK_ACCESS_API=y
> ++CONFIG_HAVE_CLK=y
> ++CONFIG_HAVE_DMA_API_DEBUG=y
> ++
> ++#
> ++# GCOV-based kernel profiling
> ++#
> ++CONFIG_HAVE_GENERIC_DMA_COHERENT=y
> ++CONFIG_RT_MUTEXES=y
> ++CONFIG_BASE_SMALL=0
> ++CONFIG_MODULES=y
> ++CONFIG_MODULE_FORCE_LOAD=y
> ++CONFIG_MODULE_UNLOAD=y
> ++# CONFIG_MODULE_FORCE_UNLOAD is not set
> ++CONFIG_MODVERSIONS=y
> ++# CONFIG_MODULE_SRCVERSION_ALL is not set
> ++CONFIG_STOP_MACHINE=y
> ++CONFIG_BLOCK=y
> ++# CONFIG_LBDAF is not set
> ++# CONFIG_BLK_DEV_BSG is not set
> ++# CONFIG_BLK_DEV_INTEGRITY is not set
> ++
> ++#
> ++# IO Schedulers
> ++#
> ++CONFIG_IOSCHED_NOOP=y
> ++# CONFIG_IOSCHED_DEADLINE is not set
> ++CONFIG_IOSCHED_CFQ=y
> ++CONFIG_DEFAULT_CFQ=y
> ++# CONFIG_DEFAULT_NOOP is not set
> ++CONFIG_DEFAULT_IOSCHED="cfq"
> ++# CONFIG_INLINE_SPIN_TRYLOCK is not set
> ++# CONFIG_INLINE_SPIN_TRYLOCK_BH is not set
> ++# CONFIG_INLINE_SPIN_LOCK is not set
> ++# CONFIG_INLINE_SPIN_LOCK_BH is not set
> ++# CONFIG_INLINE_SPIN_LOCK_IRQ is not set
> ++# CONFIG_INLINE_SPIN_LOCK_IRQSAVE is not set
> ++# CONFIG_INLINE_SPIN_UNLOCK is not set
> ++# CONFIG_INLINE_SPIN_UNLOCK_BH is not set
> ++# CONFIG_INLINE_SPIN_UNLOCK_IRQ is not set
> ++# CONFIG_INLINE_SPIN_UNLOCK_IRQRESTORE is not set
> ++# CONFIG_INLINE_READ_TRYLOCK is not set
> ++# CONFIG_INLINE_READ_LOCK is not set
> ++# CONFIG_INLINE_READ_LOCK_BH is not set
> ++# CONFIG_INLINE_READ_LOCK_IRQ is not set
> ++# CONFIG_INLINE_READ_LOCK_IRQSAVE is not set
> ++# CONFIG_INLINE_READ_UNLOCK is not set
> ++# CONFIG_INLINE_READ_UNLOCK_BH is not set
> ++# CONFIG_INLINE_READ_UNLOCK_IRQ is not set
> ++# CONFIG_INLINE_READ_UNLOCK_IRQRESTORE is not set
> ++# CONFIG_INLINE_WRITE_TRYLOCK is not set
> ++# CONFIG_INLINE_WRITE_LOCK is not set
> ++# CONFIG_INLINE_WRITE_LOCK_BH is not set
> ++# CONFIG_INLINE_WRITE_LOCK_IRQ is not set
> ++# CONFIG_INLINE_WRITE_LOCK_IRQSAVE is not set
> ++# CONFIG_INLINE_WRITE_UNLOCK is not set
> ++# CONFIG_INLINE_WRITE_UNLOCK_BH is not set
> ++# CONFIG_INLINE_WRITE_UNLOCK_IRQ is not set
> ++# CONFIG_INLINE_WRITE_UNLOCK_IRQRESTORE is not set
> ++CONFIG_MUTEX_SPIN_ON_OWNER=y
> ++CONFIG_FREEZER=y
> ++
> ++#
> ++# System Type
> ++#
> ++CONFIG_MMU=y
> ++# CONFIG_ARCH_INTEGRATOR is not set
> ++# CONFIG_ARCH_REALVIEW is not set
> ++# CONFIG_ARCH_VERSATILE is not set
> ++# CONFIG_ARCH_VEXPRESS is not set
> ++# CONFIG_ARCH_AT91 is not set
> ++# CONFIG_ARCH_BCMRING is not set
> ++# CONFIG_ARCH_CLPS711X is not set
> ++# CONFIG_ARCH_CNS3XXX is not set
> ++# CONFIG_ARCH_GEMINI is not set
> ++# CONFIG_ARCH_EBSA110 is not set
> ++# CONFIG_ARCH_EP93XX is not set
> ++# CONFIG_ARCH_FOOTBRIDGE is not set
> ++CONFIG_ARCH_MXC=y
> ++# CONFIG_ARCH_MXS is not set
> ++# CONFIG_ARCH_NETX is not set
> ++# CONFIG_ARCH_H720X is not set
> ++# CONFIG_ARCH_IOP13XX is not set
> ++# CONFIG_ARCH_IOP32X is not set
> ++# CONFIG_ARCH_IOP33X is not set
> ++# CONFIG_ARCH_IXP23XX is not set
> ++# CONFIG_ARCH_IXP2000 is not set
> ++# CONFIG_ARCH_IXP4XX is not set
> ++# CONFIG_ARCH_DOVE is not set
> ++# CONFIG_ARCH_KIRKWOOD is not set
> ++# CONFIG_ARCH_LOKI is not set
> ++# CONFIG_ARCH_LPC32XX is not set
> ++# CONFIG_ARCH_MV78XX0 is not set
> ++# CONFIG_ARCH_ORION5X is not set
> ++# CONFIG_ARCH_MMP is not set
> ++# CONFIG_ARCH_KS8695 is not set
> ++# CONFIG_ARCH_W90X900 is not set
> ++# CONFIG_ARCH_NUC93X is not set
> ++# CONFIG_ARCH_TEGRA is not set
> ++# CONFIG_ARCH_PNX4008 is not set
> ++# CONFIG_ARCH_PXA is not set
> ++# CONFIG_ARCH_MSM is not set
> ++# CONFIG_ARCH_SHMOBILE is not set
> ++# CONFIG_ARCH_RPC is not set
> ++# CONFIG_ARCH_SA1100 is not set
> ++# CONFIG_ARCH_S3C2410 is not set
> ++# CONFIG_ARCH_S3C64XX is not set
> ++# CONFIG_ARCH_S5P64X0 is not set
> ++# CONFIG_ARCH_S5PC100 is not set
> ++# CONFIG_ARCH_S5PV210 is not set
> ++# CONFIG_ARCH_EXYNOS4 is not set
> ++# CONFIG_ARCH_SHARK is not set
> ++# CONFIG_ARCH_TCC_926 is not set
> ++# CONFIG_ARCH_U300 is not set
> ++# CONFIG_ARCH_U8500 is not set
> ++# CONFIG_ARCH_NOMADIK is not set
> ++# CONFIG_ARCH_DAVINCI is not set
> ++# CONFIG_ARCH_OMAP is not set
> ++# CONFIG_PLAT_SPEAR is not set
> ++# CONFIG_ARCH_VT8500 is not set
> ++# CONFIG_GPIO_PCA953X is not set
> ++CONFIG_IMX_HAVE_PLATFORM_DMA=y
> ++CONFIG_IMX_HAVE_PLATFORM_FEC=y
> ++CONFIG_IMX_HAVE_PLATFORM_FSL_USB2_UDC=y
> ++CONFIG_IMX_HAVE_PLATFORM_IMX_CAAM=y
> ++CONFIG_IMX_HAVE_PLATFORM_IMX_I2C=y
> ++CONFIG_IMX_HAVE_PLATFORM_IMX_SSI=y
> ++CONFIG_IMX_HAVE_PLATFORM_IMX_ESAI=y
> ++CONFIG_IMX_HAVE_PLATFORM_IMX_UART=y
> ++CONFIG_IMX_HAVE_PLATFORM_MXC_EHCI=y
> ++CONFIG_IMX_HAVE_PLATFORM_SDHCI_ESDHC_IMX=y
> ++CONFIG_IMX_HAVE_PLATFORM_SPI_IMX=y
> ++CONFIG_IMX_HAVE_PLATFORM_IMX_IPUV3=y
> ++CONFIG_IMX_HAVE_PLATFORM_IMX_VPU=y
> ++CONFIG_IMX_HAVE_PLATFORM_IMX_DVFS=y
> ++CONFIG_IMX_HAVE_PLATFORM_IMX_SPDIF=y
> ++CONFIG_IMX_HAVE_PLATFORM_VIV_GPU=y
> ++CONFIG_IMX_HAVE_PLATFORM_MXC_HDMI=y
> ++CONFIG_IMX_HAVE_PLATFORM_IMX_ANATOP_THERMAL=y
> ++CONFIG_IMX_HAVE_PLATFORM_FSL_USB_WAKEUP=y
> ++CONFIG_IMX_HAVE_PLATFORM_IMX_PM=y
> ++CONFIG_IMX_HAVE_PLATFORM_IMX_ASRC=y
> ++CONFIG_IMX_HAVE_PLATFORM_IMX_MIPI_DSI=y
> ++
> ++#
> ++# Freescale MXC Implementations
> ++#
> ++# CONFIG_ARCH_MX1 is not set
> ++# CONFIG_ARCH_MX2 is not set
> ++# CONFIG_ARCH_MX25 is not set
> ++# CONFIG_ARCH_MX3 is not set
> ++# CONFIG_ARCH_MX503 is not set
> ++# CONFIG_ARCH_MX51 is not set
> ++CONFIG_ARCH_MX6=y
> ++CONFIG_FORCE_MAX_ZONEORDER=14
> ++CONFIG_ARCH_MX6Q=y
> ++CONFIG_SOC_IMX6Q=y
> ++# CONFIG_MACH_MX6Q_ARM2 is not set
> ++# CONFIG_MACH_MX6SL_ARM2 is not set
> ++# CONFIG_MACH_MX6SL_EVK is not set
> ++# CONFIG_MACH_MX6Q_SABRELITE is not set
> ++# CONFIG_MACH_MX6Q_SABRESD is not set
> ++# CONFIG_MACH_MX6Q_SABREAUTO is not set
> ++CONFIG_MACH_WANDBOARD=y
> ++CONFIG_WANDBOARD_BASE=y
> ++
> ++#
> ++# MX6 Options:
> ++#
> ++# CONFIG_IMX_PCIE is not set
> ++CONFIG_USB_EHCI_ARC_H1=y
> ++CONFIG_USB_FSL_ARC_OTG=y
> ++# CONFIG_MX6_CLK_FOR_BOOTUI_TRANS is not set
> ++# CONFIG_ISP1504_MXC is not set
> ++# CONFIG_MXC_IRQ_PRIOR is not set
> ++# CONFIG_MXC_PWM is not set
> ++# CONFIG_MXC_DEBUG_BOARD is not set
> ++# CONFIG_MXC_REBOOT_MFGMODE is not set
> ++# CONFIG_MXC_REBOOT_ANDROID_CMD is not set
> ++CONFIG_ARCH_MXC_IOMUX_V3=y
> ++CONFIG_ARCH_MXC_AUDMUX_V2=y
> ++CONFIG_IRAM_ALLOC=y
> ++CONFIG_DMA_ZONE_SIZE=184
> ++
> ++#
> ++# System MMU
> ++#
> ++
> ++#
> ++# Processor Type
> ++#
> ++CONFIG_CPU_V7=y
> ++CONFIG_CPU_32v6K=y
> ++CONFIG_CPU_32v7=y
> ++CONFIG_CPU_ABRT_EV7=y
> ++CONFIG_CPU_PABRT_V7=y
> ++CONFIG_CPU_CACHE_V7=y
> ++CONFIG_CPU_CACHE_VIPT=y
> ++CONFIG_CPU_COPY_V6=y
> ++CONFIG_CPU_TLB_V7=y
> ++CONFIG_CPU_HAS_ASID=y
> ++CONFIG_CPU_CP15=y
> ++CONFIG_CPU_CP15_MMU=y
> ++
> ++#
> ++# Processor Features
> ++#
> ++# CONFIG_ARM_THUMB is not set
> ++# CONFIG_ARM_THUMBEE is not set
> ++# CONFIG_SWP_EMULATE is not set
> ++# CONFIG_CPU_ICACHE_DISABLE is not set
> ++# CONFIG_CPU_DCACHE_DISABLE is not set
> ++# CONFIG_CPU_BPREDICT_DISABLE is not set
> ++CONFIG_OUTER_CACHE=y
> ++CONFIG_OUTER_CACHE_SYNC=y
> ++CONFIG_CACHE_L2X0=y
> ++CONFIG_CACHE_PL310=y
> ++CONFIG_ARM_L1_CACHE_SHIFT=5
> ++CONFIG_ARM_DMA_MEM_BUFFERABLE=y
> ++CONFIG_CPU_HAS_PMU=y
> ++# CONFIG_ARM_ERRATA_430973 is not set
> ++# CONFIG_ARM_ERRATA_458693 is not set
> ++# CONFIG_ARM_ERRATA_460075 is not set
> ++# CONFIG_ARM_ERRATA_742230 is not set
> ++# CONFIG_ARM_ERRATA_742231 is not set
> ++# CONFIG_PL310_ERRATA_588369 is not set
> ++# CONFIG_ARM_ERRATA_720789 is not set
> ++# CONFIG_PL310_ERRATA_727915 is not set
> ++CONFIG_ARM_ERRATA_743622=y
> ++# CONFIG_ARM_ERRATA_751472 is not set
> ++CONFIG_ARM_ERRATA_753970=y
> ++# CONFIG_ARM_ERRATA_754322 is not set
> ++# CONFIG_ARM_ERRATA_754327 is not set
> ++CONFIG_ARM_GIC=y
> ++# CONFIG_FIQ_DEBUGGER is not set
> ++
> ++#
> ++# Bus support
> ++#
> ++CONFIG_ARM_AMBA=y
> ++# CONFIG_PCI_SYSCALL is not set
> ++# CONFIG_ARCH_SUPPORTS_MSI is not set
> ++# CONFIG_PCCARD is not set
> ++# CONFIG_ARM_ERRATA_764369 is not set
> ++# CONFIG_PL310_ERRATA_769419 is not set
> ++
> ++#
> ++# Kernel Features
> ++#
> ++CONFIG_TICK_ONESHOT=y
> ++CONFIG_NO_HZ=y
> ++CONFIG_HIGH_RES_TIMERS=y
> ++CONFIG_GENERIC_CLOCKEVENTS_BUILD=y
> ++CONFIG_SMP=y
> ++CONFIG_SMP_ON_UP=y
> ++CONFIG_HAVE_ARM_SCU=y
> ++CONFIG_HAVE_ARM_TWD=y
> ++# CONFIG_VMSPLIT_3G is not set
> ++CONFIG_VMSPLIT_2G=y
> ++# CONFIG_VMSPLIT_1G is not set
> ++CONFIG_PAGE_OFFSET=0x80000000
> ++CONFIG_NR_CPUS=4
> ++CONFIG_HOTPLUG_CPU=y
> ++CONFIG_LOCAL_TIMERS=y
> ++# CONFIG_PREEMPT_NONE is not set
> ++# CONFIG_PREEMPT_VOLUNTARY is not set
> ++CONFIG_PREEMPT=y
> ++CONFIG_HZ=100
> ++# CONFIG_THUMB2_KERNEL is not set
> ++CONFIG_AEABI=y
> ++# CONFIG_OABI_COMPAT is not set
> ++# CONFIG_ARCH_SPARSEMEM_DEFAULT is not set
> ++# CONFIG_ARCH_SELECT_MEMORY_MODEL is not set
> ++CONFIG_HAVE_ARCH_PFN_VALID=y
> ++CONFIG_HIGHMEM=y
> ++# CONFIG_HIGHPTE is not set
> ++CONFIG_SELECT_MEMORY_MODEL=y
> ++CONFIG_FLATMEM_MANUAL=y
> ++CONFIG_FLATMEM=y
> ++CONFIG_FLAT_NODE_MEM_MAP=y
> ++CONFIG_HAVE_MEMBLOCK=y
> ++CONFIG_PAGEFLAGS_EXTENDED=y
> ++CONFIG_SPLIT_PTLOCK_CPUS=4
> ++CONFIG_COMPACTION=y
> ++CONFIG_MIGRATION=y
> ++# CONFIG_PHYS_ADDR_T_64BIT is not set
> ++CONFIG_ZONE_DMA_FLAG=0
> ++CONFIG_BOUNCE=y
> ++CONFIG_VIRT_TO_BUS=y
> ++# CONFIG_KSM is not set
> ++CONFIG_DEFAULT_MMAP_MIN_ADDR=4096
> ++# CONFIG_CLEANCACHE is not set
> ++CONFIG_ALIGNMENT_TRAP=y
> ++# CONFIG_UACCESS_WITH_MEMCPY is not set
> ++# CONFIG_SECCOMP is not set
> ++# CONFIG_CC_STACKPROTECTOR is not set
> ++# CONFIG_DEPRECATED_PARAM_STRUCT is not set
> ++# CONFIG_ARM_FLUSH_CONSOLE_ON_RESTART is not set
> ++
> ++#
> ++# Boot options
> ++#
> ++# CONFIG_USE_OF is not set
> ++CONFIG_ZBOOT_ROM_TEXT=0x0
> ++CONFIG_ZBOOT_ROM_BSS=0x0
> ++CONFIG_CMDLINE="noinitrd console=ttymxc0,115200"
> ++CONFIG_CMDLINE_FROM_BOOTLOADER=y
> ++# CONFIG_CMDLINE_EXTEND is not set
> ++# CONFIG_CMDLINE_FORCE is not set
> ++# CONFIG_XIP_KERNEL is not set
> ++# CONFIG_KEXEC is not set
> ++# CONFIG_CRASH_DUMP is not set
> ++# CONFIG_AUTO_ZRELADDR is not set
> ++
> ++#
> ++# CPU Power Management
> ++#
> ++
> ++#
> ++# CPU Frequency scaling
> ++#
> ++CONFIG_CPU_FREQ=y
> ++CONFIG_CPU_FREQ_TABLE=y
> ++CONFIG_CPU_FREQ_STAT=y
> ++# CONFIG_CPU_FREQ_STAT_DETAILS is not set
> ++# CONFIG_CPU_FREQ_DEFAULT_GOV_PERFORMANCE is not set
> ++# CONFIG_CPU_FREQ_DEFAULT_GOV_POWERSAVE is not set
> ++# CONFIG_CPU_FREQ_DEFAULT_GOV_USERSPACE is not set
> ++CONFIG_CPU_FREQ_DEFAULT_GOV_ONDEMAND=y
> ++# CONFIG_CPU_FREQ_DEFAULT_GOV_CONSERVATIVE is not set
> ++# CONFIG_CPU_FREQ_DEFAULT_GOV_INTERACTIVE is not set
> ++CONFIG_CPU_FREQ_GOV_PERFORMANCE=y
> ++# CONFIG_CPU_FREQ_GOV_POWERSAVE is not set
> ++# CONFIG_CPU_FREQ_GOV_USERSPACE is not set
> ++CONFIG_CPU_FREQ_GOV_ONDEMAND=y
> ++# CONFIG_CPU_FREQ_GOV_INTERACTIVE is not set
> ++# CONFIG_CPU_FREQ_GOV_CONSERVATIVE is not set
> ++CONFIG_CPU_FREQ_IMX=y
> ++CONFIG_CPU_IDLE=y
> ++CONFIG_CPU_IDLE_GOV_LADDER=y
> ++CONFIG_CPU_IDLE_GOV_MENU=y
> ++
> ++#
> ++# Floating point emulation
> ++#
> ++
> ++#
> ++# At least one emulation must be selected
> ++#
> ++CONFIG_VFP=y
> ++CONFIG_VFPv3=y
> ++CONFIG_NEON=y
> ++
> ++#
> ++# Userspace binary formats
> ++#
> ++CONFIG_BINFMT_ELF=y
> ++CONFIG_HAVE_AOUT=y
> ++# CONFIG_BINFMT_AOUT is not set
> ++# CONFIG_BINFMT_MISC is not set
> ++
> ++#
> ++# Power management options
> ++#
> ++CONFIG_SUSPEND=y
> ++CONFIG_SUSPEND_FREEZER=y
> ++CONFIG_PM_SLEEP=y
> ++CONFIG_PM_SLEEP_SMP=y
> ++CONFIG_PM_RUNTIME=y
> ++CONFIG_PM=y
> ++# CONFIG_PM_DEBUG is not set
> ++# CONFIG_APM_EMULATION is not set
> ++CONFIG_PM_RUNTIME_CLK=y
> ++# CONFIG_SUSPEND_TIME is not set
> ++CONFIG_ARCH_SUSPEND_POSSIBLE=y
> ++CONFIG_NET=y
> ++
> ++#
> ++# Networking options
> ++#
> ++CONFIG_PACKET=y
> ++CONFIG_UNIX=y
> ++# CONFIG_NET_KEY is not set
> ++CONFIG_INET=y
> ++CONFIG_IP_MULTICAST=y
> ++# CONFIG_IP_ADVANCED_ROUTER is not set
> ++# CONFIG_IP_PNP is not set
> ++# CONFIG_NET_IPIP is not set
> ++# CONFIG_NET_IPGRE_DEMUX is not set
> ++# CONFIG_IP_MROUTE is not set
> ++# CONFIG_ARPD is not set
> ++# CONFIG_SYN_COOKIES is not set
> ++# CONFIG_INET_AH is not set
> ++# CONFIG_INET_ESP is not set
> ++# CONFIG_INET_IPCOMP is not set
> ++# CONFIG_INET_XFRM_TUNNEL is not set
> ++# CONFIG_INET_TUNNEL is not set
> ++# CONFIG_INET_XFRM_MODE_TRANSPORT is not set
> ++# CONFIG_INET_XFRM_MODE_TUNNEL is not set
> ++# CONFIG_INET_XFRM_MODE_BEET is not set
> ++CONFIG_INET_LRO=y
> ++# CONFIG_INET_DIAG is not set
> ++# CONFIG_TCP_CONG_ADVANCED is not set
> ++CONFIG_TCP_CONG_CUBIC=y
> ++CONFIG_DEFAULT_TCP_CONG="cubic"
> ++# CONFIG_TCP_MD5SIG is not set
> ++# CONFIG_IPV6 is not set
> ++# CONFIG_ANDROID_PARANOID_NETWORK is not set
> ++# CONFIG_NET_ACTIVITY_STATS is not set
> ++# CONFIG_NETWORK_SECMARK is not set
> ++# CONFIG_NETWORK_PHY_TIMESTAMPING is not set
> ++# CONFIG_NETFILTER is not set
> ++# CONFIG_IP_DCCP is not set
> ++# CONFIG_IP_SCTP is not set
> ++# CONFIG_RDS is not set
> ++# CONFIG_TIPC is not set
> ++# CONFIG_ATM is not set
> ++# CONFIG_L2TP is not set
> ++# CONFIG_BRIDGE is not set
> ++# CONFIG_NET_DSA is not set
> ++# CONFIG_VLAN_8021Q is not set
> ++# CONFIG_DECNET is not set
> ++# CONFIG_LLC2 is not set
> ++# CONFIG_IPX is not set
> ++# CONFIG_ATALK is not set
> ++# CONFIG_X25 is not set
> ++# CONFIG_LAPB is not set
> ++# CONFIG_ECONET is not set
> ++# CONFIG_WAN_ROUTER is not set
> ++# CONFIG_PHONET is not set
> ++# CONFIG_IEEE802154 is not set
> ++# CONFIG_NET_SCHED is not set
> ++# CONFIG_DCB is not set
> ++# CONFIG_BATMAN_ADV is not set
> ++CONFIG_RPS=y
> ++CONFIG_RFS_ACCEL=y
> ++CONFIG_XPS=y
> ++
> ++#
> ++# Network testing
> ++#
> ++# CONFIG_NET_PKTGEN is not set
> ++# CONFIG_HAMRADIO is not set
> ++# CONFIG_CAN is not set
> ++# CONFIG_IRDA is not set
> ++CONFIG_BT=y
> ++CONFIG_BT_L2CAP=y
> ++CONFIG_BT_SCO=y
> ++CONFIG_BT_RFCOMM=y
> ++# CONFIG_BT_RFCOMM_TTY is not set
> ++CONFIG_BT_BNEP=y
> ++CONFIG_BT_BNEP_MC_FILTER=y
> ++# CONFIG_BT_BNEP_PROTO_FILTER is not set
> ++
> ++#
> ++# Bluetooth device drivers
> ++#
> ++# CONFIG_BT_HCIBTUSB is not set
> ++# CONFIG_BT_HCIBTSDIO is not set
> ++CONFIG_BT_HCIUART=y
> ++CONFIG_BT_HCIUART_H4=y
> ++# CONFIG_BT_HCIUART_BCSP is not set
> ++# CONFIG_BT_HCIUART_ATH3K is not set
> ++# CONFIG_BT_HCIUART_LL is not set
> ++# CONFIG_BT_HCIBCM203X is not set
> ++# CONFIG_BT_HCIBPA10X is not set
> ++# CONFIG_BT_HCIBFUSB is not set
> ++# CONFIG_BT_HCIVHCI is not set
> ++# CONFIG_BT_MRVL is not set
> ++# CONFIG_AF_RXRPC is not set
> ++CONFIG_WIRELESS=y
> ++CONFIG_WEXT_CORE=y
> ++CONFIG_WEXT_PROC=y
> ++CONFIG_CFG80211=y
> ++# CONFIG_NL80211_TESTMODE is not set
> ++# CONFIG_CFG80211_DEVELOPER_WARNINGS is not set
> ++# CONFIG_CFG80211_REG_DEBUG is not set
> ++# CONFIG_CFG80211_DEFAULT_PS is not set
> ++# CONFIG_CFG80211_INTERNAL_REGDB is not set
> ++CONFIG_CFG80211_WEXT=y
> ++# CONFIG_WIRELESS_EXT_SYSFS is not set
> ++# CONFIG_LIB80211 is not set
> ++# CONFIG_CFG80211_ALLOW_RECONNECT is not set
> ++# CONFIG_MAC80211 is not set
> ++# CONFIG_WIMAX is not set
> ++# CONFIG_RFKILL is not set
> ++CONFIG_RFKILL_REGULATOR=y
> ++# CONFIG_NET_9P is not set
> ++# CONFIG_CAIF is not set
> ++# CONFIG_CEPH_LIB is not set
> ++
> ++#
> ++# Device Drivers
> ++#
> ++
> ++#
> ++# Generic Driver Options
> ++#
> ++CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
> ++# CONFIG_DEVTMPFS is not set
> ++# CONFIG_STANDALONE is not set
> ++CONFIG_PREVENT_FIRMWARE_BUILD=y
> ++CONFIG_FW_LOADER=y
> ++CONFIG_FIRMWARE_IN_KERNEL=y
> ++CONFIG_EXTRA_FIRMWARE=""
> ++# CONFIG_SYS_HYPERVISOR is not set
> ++# CONFIG_SYNC is not set
> ++# CONFIG_CONNECTOR is not set
> ++# CONFIG_MTD is not set
> ++# CONFIG_PARPORT is not set
> ++CONFIG_BLK_DEV=y
> ++# CONFIG_BLK_DEV_COW_COMMON is not set
> ++# CONFIG_BLK_DEV_LOOP is not set
> ++
> ++#
> ++# DRBD disabled because PROC_FS, INET or CONNECTOR not selected
> ++#
> ++# CONFIG_BLK_DEV_NBD is not set
> ++# CONFIG_BLK_DEV_UB is not set
> ++# CONFIG_BLK_DEV_RAM is not set
> ++# CONFIG_CDROM_PKTCDVD is not set
> ++# CONFIG_ATA_OVER_ETH is not set
> ++# CONFIG_MG_DISK is not set
> ++# CONFIG_BLK_DEV_RBD is not set
> ++# CONFIG_SENSORS_LIS3LV02D is not set
> ++# CONFIG_MISC_DEVICES is not set
> ++CONFIG_HAVE_IDE=y
> ++# CONFIG_IDE is not set
> ++
> ++#
> ++# SCSI device support
> ++#
> ++CONFIG_SCSI_MOD=y
> ++# CONFIG_RAID_ATTRS is not set
> ++CONFIG_SCSI=y
> ++CONFIG_SCSI_DMA=y
> ++# CONFIG_SCSI_TGT is not set
> ++# CONFIG_SCSI_NETLINK is not set
> ++# CONFIG_SCSI_PROC_FS is not set
> ++
> ++#
> ++# SCSI support type (disk, tape, CD-ROM)
> ++#
> ++CONFIG_BLK_DEV_SD=y
> ++# CONFIG_CHR_DEV_ST is not set
> ++# CONFIG_CHR_DEV_OSST is not set
> ++# CONFIG_BLK_DEV_SR is not set
> ++# CONFIG_CHR_DEV_SG is not set
> ++# CONFIG_CHR_DEV_SCH is not set
> ++# CONFIG_SCSI_MULTI_LUN is not set
> ++# CONFIG_SCSI_CONSTANTS is not set
> ++# CONFIG_SCSI_LOGGING is not set
> ++# CONFIG_SCSI_SCAN_ASYNC is not set
> ++# CONFIG_SCSI_WAIT_SCAN is not set
> ++
> ++#
> ++# SCSI Transports
> ++#
> ++# CONFIG_SCSI_SPI_ATTRS is not set
> ++# CONFIG_SCSI_FC_ATTRS is not set
> ++# CONFIG_SCSI_ISCSI_ATTRS is not set
> ++# CONFIG_SCSI_SAS_ATTRS is not set
> ++# CONFIG_SCSI_SAS_LIBSAS is not set
> ++# CONFIG_SCSI_SRP_ATTRS is not set
> ++# CONFIG_SCSI_LOWLEVEL is not set
> ++# CONFIG_SCSI_DH is not set
> ++# CONFIG_SCSI_OSD_INITIATOR is not set
> ++# CONFIG_ATA is not set
> ++# CONFIG_MD is not set
> ++# CONFIG_TARGET_CORE is not set
> ++CONFIG_NETDEVICES=y
> ++# CONFIG_DUMMY is not set
> ++# CONFIG_BONDING is not set
> ++# CONFIG_MACVLAN is not set
> ++# CONFIG_EQUALIZER is not set
> ++# CONFIG_TUN is not set
> ++# CONFIG_VETH is not set
> ++# CONFIG_MII is not set
> ++CONFIG_PHYLIB=y
> ++
> ++#
> ++# MII PHY device drivers
> ++#
> ++# CONFIG_MARVELL_PHY is not set
> ++# CONFIG_DAVICOM_PHY is not set
> ++# CONFIG_QSEMI_PHY is not set
> ++# CONFIG_LXT_PHY is not set
> ++# CONFIG_CICADA_PHY is not set
> ++# CONFIG_VITESSE_PHY is not set
> ++# CONFIG_SMSC_PHY is not set
> ++# CONFIG_BROADCOM_PHY is not set
> ++# CONFIG_ICPLUS_PHY is not set
> ++# CONFIG_REALTEK_PHY is not set
> ++# CONFIG_NATIONAL_PHY is not set
> ++# CONFIG_STE10XP is not set
> ++# CONFIG_LSI_ET1011C_PHY is not set
> ++# CONFIG_MICREL_PHY is not set
> ++# CONFIG_FIXED_PHY is not set
> ++# CONFIG_MDIO_BITBANG is not set
> ++CONFIG_NET_ETHERNET=y
> ++# CONFIG_AX88796 is not set
> ++# CONFIG_SMC91X is not set
> ++# CONFIG_DM9000 is not set
> ++# CONFIG_ENC28J60 is not set
> ++# CONFIG_ETHOC is not set
> ++# CONFIG_SMC911X is not set
> ++# CONFIG_SMSC911X is not set
> ++# CONFIG_DNET is not set
> ++# CONFIG_IBM_NEW_EMAC_ZMII is not set
> ++# CONFIG_IBM_NEW_EMAC_RGMII is not set
> ++# CONFIG_IBM_NEW_EMAC_TAH is not set
> ++# CONFIG_IBM_NEW_EMAC_EMAC4 is not set
> ++# CONFIG_IBM_NEW_EMAC_NO_FLOW_CTRL is not set
> ++# CONFIG_IBM_NEW_EMAC_MAL_CLR_ICINTSTAT is not set
> ++# CONFIG_IBM_NEW_EMAC_MAL_COMMON_ERR is not set
> ++# CONFIG_B44 is not set
> ++# CONFIG_KS8842 is not set
> ++# CONFIG_KS8851 is not set
> ++# CONFIG_KS8851_MLL is not set
> ++CONFIG_FEC=y
> ++CONFIG_FEC_NAPI=y
> ++# CONFIG_FEC_1588 is not set
> ++# CONFIG_FTMAC100 is not set
> ++# CONFIG_NETDEV_1000 is not set
> ++# CONFIG_NETDEV_10000 is not set
> ++CONFIG_WLAN=y
> ++# CONFIG_USB_ZD1201 is not set
> ++# CONFIG_USB_NET_RNDIS_WLAN is not set
> ++# CONFIG_WIFI_CONTROL_FUNC is not set
> ++# CONFIG_ATH_COMMON is not set
> ++# CONFIG_BCM4329 is not set
> ++# CONFIG_BCMDHD is not set
> ++CONFIG_BRCMUTIL=m
> ++CONFIG_BRCMFMAC=m
> ++CONFIG_BRCMFMAC_SDIO=y
> ++# CONFIG_BRCMFMAC_SDIO_OOB is not set
> ++# CONFIG_BRCMFMAC_USB is not set
> ++# CONFIG_BRCMDBG is not set
> ++# CONFIG_HOSTAP is not set
> ++# CONFIG_IWM is not set
> ++# CONFIG_LIBERTAS is not set
> ++# CONFIG_MWIFIEX is not set
> ++
> ++#
> ++# Enable WiMAX (Networking options) to see the WiMAX drivers
> ++#
> ++
> ++#
> ++# USB Network Adapters
> ++#
> ++# CONFIG_USB_CATC is not set
> ++# CONFIG_USB_KAWETH is not set
> ++# CONFIG_USB_PEGASUS is not set
> ++# CONFIG_USB_RTL8150 is not set
> ++# CONFIG_USB_USBNET is not set
> ++# CONFIG_USB_IPHETH is not set
> ++# CONFIG_WAN is not set
> ++
> ++#
> ++# CAIF transport drivers
> ++#
> ++# CONFIG_PPP is not set
> ++# CONFIG_SLIP is not set
> ++# CONFIG_NETCONSOLE is not set
> ++# CONFIG_NETPOLL is not set
> ++# CONFIG_NET_POLL_CONTROLLER is not set
> ++# CONFIG_ISDN is not set
> ++# CONFIG_PHONE is not set
> ++
> ++#
> ++# Input device support
> ++#
> ++CONFIG_INPUT=y
> ++# CONFIG_INPUT_FF_MEMLESS is not set
> ++# CONFIG_INPUT_POLLDEV is not set
> ++# CONFIG_INPUT_SPARSEKMAP is not set
> ++
> ++#
> ++# Userland interfaces
> ++#
> ++# CONFIG_INPUT_MOUSEDEV is not set
> ++# CONFIG_INPUT_JOYDEV is not set
> ++# CONFIG_INPUT_EVDEV is not set
> ++# CONFIG_INPUT_EVBUG is not set
> ++# CONFIG_INPUT_KEYRESET is not set
> ++
> ++#
> ++# Input Device Drivers
> ++#
> ++# CONFIG_INPUT_KEYBOARD is not set
> ++# CONFIG_INPUT_MOUSE is not set
> ++# CONFIG_INPUT_JOYSTICK is not set
> ++# CONFIG_INPUT_TABLET is not set
> ++# CONFIG_INPUT_TOUCHSCREEN is not set
> ++# CONFIG_INPUT_MISC is not set
> ++
> ++#
> ++# Hardware I/O ports
> ++#
> ++CONFIG_SERIO=y
> ++# CONFIG_SERIO_SERPORT is not set
> ++# CONFIG_SERIO_AMBAKMI is not set
> ++# CONFIG_SERIO_LIBPS2 is not set
> ++# CONFIG_SERIO_RAW is not set
> ++# CONFIG_SERIO_ALTERA_PS2 is not set
> ++# CONFIG_SERIO_PS2MULT is not set
> ++# CONFIG_GAMEPORT is not set
> ++
> ++#
> ++# Character devices
> ++#
> ++CONFIG_VT=y
> ++# CONFIG_CONSOLE_TRANSLATIONS is not set
> ++CONFIG_VT_CONSOLE=y
> ++CONFIG_HW_CONSOLE=y
> ++# CONFIG_VT_HW_CONSOLE_BINDING is not set
> ++CONFIG_UNIX98_PTYS=y
> ++# CONFIG_DEVPTS_MULTIPLE_INSTANCES is not set
> ++# CONFIG_LEGACY_PTYS is not set
> ++# CONFIG_SERIAL_NONSTANDARD is not set
> ++# CONFIG_N_GSM is not set
> ++# CONFIG_TRACE_SINK is not set
> ++# CONFIG_DEVMEM is not set
> ++# CONFIG_DEVKMEM is not set
> ++
> ++#
> ++# Serial drivers
> ++#
> ++# CONFIG_SERIAL_8250 is not set
> ++
> ++#
> ++# Non-8250 serial port support
> ++#
> ++# CONFIG_SERIAL_AMBA_PL010 is not set
> ++# CONFIG_SERIAL_AMBA_PL011 is not set
> ++# CONFIG_SERIAL_MAX3100 is not set
> ++# CONFIG_SERIAL_MAX3107 is not set
> ++CONFIG_SERIAL_IMX=y
> ++CONFIG_SERIAL_IMX_CONSOLE=y
> ++CONFIG_SERIAL_CORE=y
> ++CONFIG_SERIAL_CORE_CONSOLE=y
> ++# CONFIG_SERIAL_TIMBERDALE is not set
> ++# CONFIG_SERIAL_ALTERA_JTAGUART is not set
> ++# CONFIG_SERIAL_ALTERA_UART is not set
> ++# CONFIG_SERIAL_IFX6X60 is not set
> ++# CONFIG_SERIAL_XILINX_PS_UART is not set
> ++# CONFIG_TTY_PRINTK is not set
> ++# CONFIG_FSL_OTP is not set
> ++# CONFIG_HVC_DCC is not set
> ++# CONFIG_IPMI_HANDLER is not set
> ++# CONFIG_HW_RANDOM is not set
> ++# CONFIG_R3964 is not set
> ++# CONFIG_RAW_DRIVER is not set
> ++# CONFIG_TCG_TPM is not set
> ++# CONFIG_DCC_TTY is not set
> ++# CONFIG_RAMOOPS is not set
> ++# CONFIG_MXS_VIIM is not set
> ++CONFIG_I2C=y
> ++CONFIG_I2C_BOARDINFO=y
> ++# CONFIG_I2C_COMPAT is not set
> ++CONFIG_I2C_CHARDEV=y
> ++# CONFIG_I2C_MUX is not set
> ++CONFIG_I2C_HELPER_AUTO=y
> ++
> ++#
> ++# I2C Hardware Bus support
> ++#
> ++
> ++#
> ++# I2C system bus drivers (mostly embedded / system-on-chip)
> ++#
> ++# CONFIG_I2C_DESIGNWARE is not set
> ++# CONFIG_I2C_GPIO is not set
> ++CONFIG_I2C_IMX=y
> ++# CONFIG_I2C_OCORES is not set
> ++# CONFIG_I2C_PCA_PLATFORM is not set
> ++# CONFIG_I2C_PXA_PCI is not set
> ++# CONFIG_I2C_SIMTEC is not set
> ++# CONFIG_I2C_XILINX is not set
> ++
> ++#
> ++# External I2C/SMBus adapter drivers
> ++#
> ++# CONFIG_I2C_DIOLAN_U2C is not set
> ++# CONFIG_I2C_PARPORT_LIGHT is not set
> ++# CONFIG_I2C_TAOS_EVM is not set
> ++# CONFIG_I2C_TINY_USB is not set
> ++
> ++#
> ++# Other I2C/SMBus bus drivers
> ++#
> ++# CONFIG_I2C_STUB is not set
> ++# CONFIG_I2C_DEBUG_CORE is not set
> ++# CONFIG_I2C_DEBUG_ALGO is not set
> ++# CONFIG_I2C_DEBUG_BUS is not set
> ++CONFIG_SPI=y
> ++CONFIG_SPI_MASTER=y
> ++
> ++#
> ++# SPI Master Controller Drivers
> ++#
> ++# CONFIG_SPI_ALTERA is not set
> ++CONFIG_SPI_BITBANG=y
> ++# CONFIG_SPI_GPIO is not set
> ++CONFIG_SPI_IMX_VER_2_3=y
> ++CONFIG_SPI_IMX=y
> ++# CONFIG_SPI_OC_TINY is not set
> ++# CONFIG_SPI_PL022 is not set
> ++# CONFIG_SPI_PXA2XX_PCI is not set
> ++# CONFIG_SPI_XILINX is not set
> ++# CONFIG_SPI_DESIGNWARE is not set
> ++
> ++#
> ++# SPI Protocol Masters
> ++#
> ++# CONFIG_SPI_SPIDEV is not set
> ++# CONFIG_SPI_TLE62X0 is not set
> ++
> ++#
> ++# PPS support
> ++#
> ++# CONFIG_PPS is not set
> ++
> ++#
> ++# PPS generators support
> ++#
> ++
> ++#
> ++# PTP clock support
> ++#
> ++
> ++#
> ++# Enable Device Drivers -> PPS to see the PTP clock options.
> ++#
> ++CONFIG_ARCH_REQUIRE_GPIOLIB=y
> ++CONFIG_GPIOLIB=y
> ++CONFIG_GPIO_SYSFS=y
> ++
> ++#
> ++# Memory mapped GPIO drivers:
> ++#
> ++# CONFIG_GPIO_BASIC_MMIO is not set
> ++# CONFIG_GPIO_IT8761E is not set
> ++# CONFIG_GPIO_PL061 is not set
> ++
> ++#
> ++# I2C GPIO expanders:
> ++#
> ++# CONFIG_GPIO_MAX7300 is not set
> ++# CONFIG_GPIO_MAX732X is not set
> ++# CONFIG_GPIO_PCF857X is not set
> ++# CONFIG_GPIO_SX150X is not set
> ++# CONFIG_GPIO_ADP5588 is not set
> ++
> ++#
> ++# PCI GPIO expanders:
> ++#
> ++
> ++#
> ++# SPI GPIO expanders:
> ++#
> ++# CONFIG_GPIO_MAX7301 is not set
> ++# CONFIG_GPIO_MCP23S08 is not set
> ++# CONFIG_GPIO_MC33880 is not set
> ++# CONFIG_GPIO_74X164 is not set
> ++
> ++#
> ++# AC97 GPIO expanders:
> ++#
> ++
> ++#
> ++# MODULbus GPIO expanders:
> ++#
> ++# CONFIG_W1 is not set
> ++CONFIG_POWER_SUPPLY=y
> ++# CONFIG_POWER_SUPPLY_DEBUG is not set
> ++# CONFIG_PDA_POWER is not set
> ++# CONFIG_TEST_POWER is not set
> ++# CONFIG_BATTERY_DS2780 is not set
> ++# CONFIG_BATTERY_DS2782 is not set
> ++# CONFIG_BATTERY_BQ20Z75 is not set
> ++# CONFIG_BATTERY_BQ27x00 is not set
> ++# CONFIG_BATTERY_MAX17040 is not set
> ++# CONFIG_BATTERY_MAX17042 is not set
> ++# CONFIG_CHARGER_ISP1704 is not set
> ++# CONFIG_CHARGER_MAX8903 is not set
> ++# CONFIG_SABRESD_MAX8903 is not set
> ++# CONFIG_CHARGER_GPIO is not set
> ++# CONFIG_HWMON is not set
> ++CONFIG_THERMAL=y
> ++# CONFIG_WATCHDOG is not set
> ++CONFIG_SSB_POSSIBLE=y
> ++
> ++#
> ++# Sonics Silicon Backplane
> ++#
> ++# CONFIG_SSB is not set
> ++CONFIG_BCMA_POSSIBLE=y
> ++
> ++#
> ++# Broadcom specific AMBA
> ++#
> ++# CONFIG_BCMA is not set
> ++CONFIG_MFD_SUPPORT=y
> ++CONFIG_MFD_CORE=y
> ++# CONFIG_MFD_88PM860X is not set
> ++# CONFIG_MFD_SM501 is not set
> ++# CONFIG_MFD_ASIC3 is not set
> ++# CONFIG_HTC_EGPIO is not set
> ++# CONFIG_HTC_PASIC3 is not set
> ++# CONFIG_HTC_I2CPLD is not set
> ++# CONFIG_UCB1400_CORE is not set
> ++# CONFIG_TPS6105X is not set
> ++# CONFIG_TPS65010 is not set
> ++# CONFIG_TPS6507X is not set
> ++# CONFIG_MFD_TPS6586X is not set
> ++# CONFIG_TWL4030_CORE is not set
> ++# CONFIG_MFD_STMPE is not set
> ++# CONFIG_MFD_TC3589X is not set
> ++# CONFIG_MFD_TMIO is not set
> ++# CONFIG_MFD_T7L66XB is not set
> ++# CONFIG_MFD_TC6387XB is not set
> ++# CONFIG_MFD_TC6393XB is not set
> ++# CONFIG_PMIC_DA903X is not set
> ++# CONFIG_PMIC_ADP5520 is not set
> ++# CONFIG_MFD_MAX8925 is not set
> ++# CONFIG_MFD_MAX8997 is not set
> ++# CONFIG_MFD_MAX8998 is not set
> ++# CONFIG_MFD_WM8400 is not set
> ++# CONFIG_MFD_WM831X_I2C is not set
> ++# CONFIG_MFD_WM831X_SPI is not set
> ++# CONFIG_MFD_WM8350_I2C is not set
> ++# CONFIG_MFD_WM8994 is not set
> ++# CONFIG_MFD_PCF50633 is not set
> ++# CONFIG_PMIC_DIALOG is not set
> ++# CONFIG_MFD_MC_PMIC is not set
> ++# CONFIG_MFD_MC34708 is not set
> ++# CONFIG_MFD_PFUZE is not set
> ++# CONFIG_MFD_MC13XXX is not set
> ++# CONFIG_ABX500_CORE is not set
> ++# CONFIG_EZX_PCAP is not set
> ++# CONFIG_MFD_WL1273_CORE is not set
> ++# CONFIG_MFD_TPS65910 is not set
> ++# CONFIG_MFD_MAX17135 is not set
> ++CONFIG_MFD_MXC_HDMI=y
> ++CONFIG_REGULATOR=y
> ++# CONFIG_REGULATOR_DEBUG is not set
> ++CONFIG_REGULATOR_DUMMY=y
> ++CONFIG_REGULATOR_FIXED_VOLTAGE=y
> ++# CONFIG_REGULATOR_VIRTUAL_CONSUMER is not set
> ++# CONFIG_REGULATOR_USERSPACE_CONSUMER is not set
> ++# CONFIG_REGULATOR_BQ24022 is not set
> ++# CONFIG_REGULATOR_MAX1586 is not set
> ++# CONFIG_REGULATOR_MAX8649 is not set
> ++# CONFIG_REGULATOR_MAX8660 is not set
> ++# CONFIG_REGULATOR_MAX8952 is not set
> ++# CONFIG_REGULATOR_LP3971 is not set
> ++# CONFIG_REGULATOR_LP3972 is not set
> ++# CONFIG_REGULATOR_MC34708 is not set
> ++# CONFIG_REGULATOR_TPS65023 is not set
> ++# CONFIG_REGULATOR_TPS6507X is not set
> ++# CONFIG_REGULATOR_ISL6271A is not set
> ++# CONFIG_REGULATOR_AD5398 is not set
> ++CONFIG_REGULATOR_ANATOP=y
> ++# CONFIG_REGULATOR_TPS6524X is not set
> ++CONFIG_MEDIA_SUPPORT=y
> ++
> ++#
> ++# Multimedia core support
> ++#
> ++# CONFIG_MEDIA_CONTROLLER is not set
> ++CONFIG_VIDEO_DEV=y
> ++CONFIG_VIDEO_V4L2_COMMON=y
> ++# CONFIG_DVB_CORE is not set
> ++CONFIG_VIDEO_MEDIA=y
> ++
> ++#
> ++# Multimedia drivers
> ++#
> ++# CONFIG_RC_CORE is not set
> ++# CONFIG_MEDIA_ATTACH is not set
> ++CONFIG_MEDIA_TUNER=y
> ++# CONFIG_MEDIA_TUNER_CUSTOMISE is not set
> ++CONFIG_MEDIA_TUNER_SIMPLE=y
> ++CONFIG_MEDIA_TUNER_TDA8290=y
> ++CONFIG_MEDIA_TUNER_TDA827X=y
> ++CONFIG_MEDIA_TUNER_TDA18271=y
> ++CONFIG_MEDIA_TUNER_TDA9887=y
> ++CONFIG_MEDIA_TUNER_TEA5761=y
> ++CONFIG_MEDIA_TUNER_TEA5767=y
> ++CONFIG_MEDIA_TUNER_MT20XX=y
> ++CONFIG_MEDIA_TUNER_XC2028=y
> ++CONFIG_MEDIA_TUNER_XC5000=y
> ++CONFIG_MEDIA_TUNER_MC44S803=y
> ++CONFIG_VIDEO_V4L2=y
> ++CONFIG_VIDEOBUF_GEN=y
> ++CONFIG_VIDEOBUF_DMA_CONTIG=y
> ++CONFIG_VIDEO_CAPTURE_DRIVERS=y
> ++# CONFIG_VIDEO_ADV_DEBUG is not set
> ++# CONFIG_VIDEO_FIXED_MINOR_RANGES is not set
> ++# CONFIG_VIDEO_HELPER_CHIPS_AUTO is not set
> ++
> ++#
> ++# Encoders, decoders, sensors and other helper chips
> ++#
> ++
> ++#
> ++# Audio decoders, processors and mixers
> ++#
> ++# CONFIG_VIDEO_TVAUDIO is not set
> ++# CONFIG_VIDEO_TDA7432 is not set
> ++# CONFIG_VIDEO_TDA9840 is not set
> ++# CONFIG_VIDEO_TEA6415C is not set
> ++# CONFIG_VIDEO_TEA6420 is not set
> ++# CONFIG_VIDEO_MSP3400 is not set
> ++# CONFIG_VIDEO_CS5345 is not set
> ++# CONFIG_VIDEO_CS53L32A is not set
> ++# CONFIG_VIDEO_TLV320AIC23B is not set
> ++# CONFIG_VIDEO_WM8775 is not set
> ++# CONFIG_VIDEO_WM8739 is not set
> ++# CONFIG_VIDEO_VP27SMPX is not set
> ++
> ++#
> ++# RDS decoders
> ++#
> ++# CONFIG_VIDEO_SAA6588 is not set
> ++
> ++#
> ++# Video decoders
> ++#
> ++# CONFIG_VIDEO_ADV7180 is not set
> ++# CONFIG_VIDEO_BT819 is not set
> ++# CONFIG_VIDEO_BT856 is not set
> ++# CONFIG_VIDEO_BT866 is not set
> ++# CONFIG_VIDEO_KS0127 is not set
> ++# CONFIG_VIDEO_SAA7110 is not set
> ++# CONFIG_VIDEO_SAA711X is not set
> ++# CONFIG_VIDEO_SAA7191 is not set
> ++# CONFIG_VIDEO_TVP514X is not set
> ++# CONFIG_VIDEO_TVP5150 is not set
> ++# CONFIG_VIDEO_TVP7002 is not set
> ++# CONFIG_VIDEO_VPX3220 is not set
> ++
> ++#
> ++# Video and audio decoders
> ++#
> ++# CONFIG_VIDEO_SAA717X is not set
> ++# CONFIG_VIDEO_CX25840 is not set
> ++
> ++#
> ++# MPEG video encoders
> ++#
> ++# CONFIG_VIDEO_CX2341X is not set
> ++
> ++#
> ++# Video encoders
> ++#
> ++# CONFIG_VIDEO_SAA7127 is not set
> ++# CONFIG_VIDEO_SAA7185 is not set
> ++# CONFIG_VIDEO_ADV7170 is not set
> ++# CONFIG_VIDEO_ADV7175 is not set
> ++# CONFIG_VIDEO_ADV7343 is not set
> ++# CONFIG_VIDEO_AK881X is not set
> ++
> ++#
> ++# Camera sensor devices
> ++#
> ++# CONFIG_VIDEO_OV7670 is not set
> ++# CONFIG_VIDEO_MT9V011 is not set
> ++# CONFIG_VIDEO_TCM825X is not set
> ++
> ++#
> ++# Video improvement chips
> ++#
> ++# CONFIG_VIDEO_UPD64031A is not set
> ++# CONFIG_VIDEO_UPD64083 is not set
> ++
> ++#
> ++# Miscelaneous helper chips
> ++#
> ++# CONFIG_VIDEO_THS7303 is not set
> ++# CONFIG_VIDEO_M52790 is not set
> ++# CONFIG_VIDEO_VIVI is not set
> ++# CONFIG_VIDEO_MXC_CAMERA is not set
> ++CONFIG_VIDEO_MXC_OUTPUT=y
> ++CONFIG_VIDEO_MXC_IPU_OUTPUT=y
> ++# CONFIG_VIDEO_MXC_IPUV1_WVGA_OUTPUT is not set
> ++# CONFIG_VIDEO_MXC_OPL is not set
> ++# CONFIG_VIDEO_CPIA2 is not set
> ++# CONFIG_VIDEO_TIMBERDALE is not set
> ++# CONFIG_VIDEO_SR030PC30 is not set
> ++# CONFIG_VIDEO_NOON010PC30 is not set
> ++# CONFIG_SOC_CAMERA is not set
> ++# CONFIG_V4L_USB_DRIVERS is not set
> ++# CONFIG_V4L_MEM2MEM_DRIVERS is not set
> ++# CONFIG_RADIO_ADAPTERS is not set
> ++
> ++#
> ++# Graphics support
> ++#
> ++# CONFIG_DRM is not set
> ++# CONFIG_ION is not set
> ++# CONFIG_VGASTATE is not set
> ++CONFIG_VIDEO_OUTPUT_CONTROL=y
> ++CONFIG_FB=y
> ++# CONFIG_FIRMWARE_EDID is not set
> ++# CONFIG_FB_DDC is not set
> ++# CONFIG_FB_BOOT_VESA_SUPPORT is not set
> ++CONFIG_FB_CFB_FILLRECT=y
> ++CONFIG_FB_CFB_COPYAREA=y
> ++CONFIG_FB_CFB_IMAGEBLIT=y
> ++# CONFIG_FB_CFB_REV_PIXELS_IN_BYTE is not set
> ++# CONFIG_FB_SYS_FILLRECT is not set
> ++# CONFIG_FB_SYS_COPYAREA is not set
> ++# CONFIG_FB_SYS_IMAGEBLIT is not set
> ++# CONFIG_FB_FOREIGN_ENDIAN is not set
> ++# CONFIG_FB_SYS_FOPS is not set
> ++# CONFIG_FB_WMT_GE_ROPS is not set
> ++# CONFIG_FB_SVGALIB is not set
> ++# CONFIG_FB_MACMODES is not set
> ++# CONFIG_FB_BACKLIGHT is not set
> ++CONFIG_FB_MODE_HELPERS=y
> ++# CONFIG_FB_TILEBLITTING is not set
> ++
> ++#
> ++# Frame buffer hardware drivers
> ++#
> ++# CONFIG_FB_ARMCLCD is not set
> ++# CONFIG_FB_S1D13XXX is not set
> ++# CONFIG_FB_TMIO is not set
> ++# CONFIG_FB_UDL is not set
> ++# CONFIG_FB_VIRTUAL is not set
> ++# CONFIG_FB_METRONOME is not set
> ++# CONFIG_FB_BROADSHEET is not set
> ++# CONFIG_BACKLIGHT_LCD_SUPPORT is not set
> ++
> ++#
> ++# Display device support
> ++#
> ++CONFIG_DISPLAY_SUPPORT=y
> ++
> ++#
> ++# Display hardware drivers
> ++#
> ++CONFIG_FB_MXC=y
> ++CONFIG_FB_MXC_EDID=y
> ++CONFIG_FB_MXC_SYNC_PANEL=y
> ++# CONFIG_FB_MXC_EPSON_VGA_SYNC_PANEL is not set
> ++CONFIG_FB_MXC_LDB=y
> ++# CONFIG_FB_MXC_MIPI_DSI is not set
> ++# CONFIG_FB_MXC_CLAA_WVGA_SYNC_PANEL is not set
> ++# CONFIG_FB_MXC_SEIKO_WVGA_SYNC_PANEL is not set
> ++# CONFIG_FB_MXC_SII902X is not set
> ++# CONFIG_FB_MXC_CH7026 is not set
> ++# CONFIG_FB_MXC_TVOUT_CH7024 is not set
> ++# CONFIG_FB_MXC_ASYNC_PANEL is not set
> ++# CONFIG_FB_MXC_EINK_PANEL is not set
> ++# CONFIG_FB_MXC_SIPIX_PANEL is not set
> ++# CONFIG_FB_MXC_ELCDIF_FB is not set
> ++CONFIG_FB_MXC_HDMI=y
> ++
> ++#
> ++# Console display driver support
> ++#
> ++CONFIG_DUMMY_CONSOLE=y
> ++CONFIG_FRAMEBUFFER_CONSOLE=y
> ++# CONFIG_FRAMEBUFFER_CONSOLE_DETECT_PRIMARY is not set
> ++# CONFIG_FRAMEBUFFER_CONSOLE_ROTATION is not set
> ++# CONFIG_FONTS is not set
> ++CONFIG_FONT_8x8=y
> ++CONFIG_FONT_8x16=y
> ++CONFIG_LOGO=y
> ++# CONFIG_LOGO_LINUX_MONO is not set
> ++# CONFIG_LOGO_LINUX_VGA16 is not set
> ++CONFIG_LOGO_LINUX_CLUT224=y
> ++CONFIG_SOUND=y
> ++# CONFIG_SOUND_OSS_CORE is not set
> ++CONFIG_SND=y
> ++CONFIG_SND_TIMER=y
> ++CONFIG_SND_PCM=y
> ++CONFIG_SND_JACK=y
> ++# CONFIG_SND_SEQUENCER is not set
> ++# CONFIG_SND_MIXER_OSS is not set
> ++# CONFIG_SND_PCM_OSS is not set
> ++# CONFIG_SND_HRTIMER is not set
> ++# CONFIG_SND_DYNAMIC_MINORS is not set
> ++# CONFIG_SND_SUPPORT_OLD_API is not set
> ++# CONFIG_SND_VERBOSE_PROCFS is not set
> ++# CONFIG_SND_VERBOSE_PRINTK is not set
> ++# CONFIG_SND_DEBUG is not set
> ++# CONFIG_SND_RAWMIDI_SEQ is not set
> ++# CONFIG_SND_OPL3_LIB_SEQ is not set
> ++# CONFIG_SND_OPL4_LIB_SEQ is not set
> ++# CONFIG_SND_SBAWE_SEQ is not set
> ++# CONFIG_SND_EMU10K1_SEQ is not set
> ++# CONFIG_SND_DRIVERS is not set
> ++# CONFIG_SND_ARM is not set
> ++# CONFIG_SND_SPI is not set
> ++# CONFIG_SND_USB is not set
> ++CONFIG_SND_SOC=y
> ++# CONFIG_SND_SOC_CACHE_LZO is not set
> ++CONFIG_SND_SOC_AC97_BUS=y
> ++CONFIG_SND_IMX_SOC=y
> ++CONFIG_SND_MXC_SOC_MX2=y
> ++CONFIG_SND_MXC_SOC_SPDIF_DAI=y
> ++CONFIG_SND_SOC_IMX_SGTL5000=y
> ++# CONFIG_SND_SOC_IMX_WM8962 is not set
> ++# CONFIG_SND_SOC_IMX_SI4763 is not set
> ++CONFIG_SND_SOC_IMX_SPDIF=y
> ++CONFIG_SND_SOC_IMX_HDMI=y
> ++CONFIG_SND_SOC_I2C_AND_SPI=y
> ++# CONFIG_SND_SOC_ALL_CODECS is not set
> ++CONFIG_SND_SOC_MXC_HDMI=y
> ++CONFIG_SND_SOC_MXC_SPDIF=y
> ++CONFIG_SND_SOC_SGTL5000=y
> ++# CONFIG_SOUND_PRIME is not set
> ++CONFIG_AC97_BUS=y
> ++# CONFIG_HID_SUPPORT is not set
> ++CONFIG_USB_SUPPORT=y
> ++CONFIG_USB_ARCH_HAS_HCD=y
> ++# CONFIG_USB_ARCH_HAS_OHCI is not set
> ++CONFIG_USB_ARCH_HAS_EHCI=y
> ++CONFIG_USB=y
> ++# CONFIG_USB_DEBUG is not set
> ++# CONFIG_USB_ANNOUNCE_NEW_DEVICES is not set
> ++
> ++#
> ++# Miscellaneous USB options
> ++#
> ++CONFIG_USB_DEVICEFS=y
> ++# CONFIG_USB_DEVICE_CLASS is not set
> ++# CONFIG_USB_DYNAMIC_MINORS is not set
> ++# CONFIG_USB_SUSPEND is not set
> ++# CONFIG_USB_OTG_WHITELIST is not set
> ++# CONFIG_USB_OTG_BLACKLIST_HUB is not set
> ++# CONFIG_USB_MON is not set
> ++# CONFIG_USB_WUSB is not set
> ++# CONFIG_USB_WUSB_CBAF is not set
> ++
> ++#
> ++# USB Host Controller Drivers
> ++#
> ++# CONFIG_USB_C67X00_HCD is not set
> ++CONFIG_USB_EHCI_HCD=y
> ++CONFIG_USB_EHCI_ARC=y
> ++CONFIG_USB_EHCI_ARC_OTG=y
> ++# CONFIG_USB_EHCI_ARC_HSIC is not set
> ++# CONFIG_USB_STATIC_IRAM is not set
> ++CONFIG_USB_EHCI_ROOT_HUB_TT=y
> ++CONFIG_USB_EHCI_TT_NEWSCHED=y
> ++# CONFIG_USB_EHCI_MXC is not set
> ++# CONFIG_USB_OXU210HP_HCD is not set
> ++# CONFIG_USB_ISP116X_HCD is not set
> ++# CONFIG_USB_ISP1760_HCD is not set
> ++# CONFIG_USB_ISP1362_HCD is not set
> ++# CONFIG_USB_SL811_HCD is not set
> ++# CONFIG_USB_R8A66597_HCD is not set
> ++# CONFIG_USB_HWA_HCD is not set
> ++# CONFIG_USB_MUSB_HDRC is not set
> ++
> ++#
> ++# USB Device Class drivers
> ++#
> ++# CONFIG_USB_ACM is not set
> ++# CONFIG_USB_PRINTER is not set
> ++# CONFIG_USB_WDM is not set
> ++# CONFIG_USB_TMC is not set
> ++
> ++#
> ++# NOTE: USB_STORAGE depends on SCSI but BLK_DEV_SD may
> ++#
> ++
> ++#
> ++# also be needed; see USB_STORAGE Help for more info
> ++#
> ++CONFIG_USB_STORAGE=y
> ++# CONFIG_USB_STORAGE_DEBUG is not set
> ++# CONFIG_USB_STORAGE_REALTEK is not set
> ++# CONFIG_USB_STORAGE_DATAFAB is not set
> ++# CONFIG_USB_STORAGE_FREECOM is not set
> ++# CONFIG_USB_STORAGE_ISD200 is not set
> ++# CONFIG_USB_STORAGE_USBAT is not set
> ++# CONFIG_USB_STORAGE_SDDR09 is not set
> ++# CONFIG_USB_STORAGE_SDDR55 is not set
> ++# CONFIG_USB_STORAGE_JUMPSHOT is not set
> ++# CONFIG_USB_STORAGE_ALAUDA is not set
> ++# CONFIG_USB_STORAGE_ONETOUCH is not set
> ++# CONFIG_USB_STORAGE_KARMA is not set
> ++# CONFIG_USB_STORAGE_CYPRESS_ATACB is not set
> ++# CONFIG_USB_STORAGE_ENE_UB6250 is not set
> ++# CONFIG_USB_UAS is not set
> ++# CONFIG_USB_LIBUSUAL is not set
> ++
> ++#
> ++# USB Imaging devices
> ++#
> ++# CONFIG_USB_MDC800 is not set
> ++# CONFIG_USB_MICROTEK is not set
> ++
> ++#
> ++# USB port drivers
> ++#
> ++# CONFIG_USB_SERIAL is not set
> ++
> ++#
> ++# USB Miscellaneous drivers
> ++#
> ++# CONFIG_USB_EMI62 is not set
> ++# CONFIG_USB_EMI26 is not set
> ++# CONFIG_USB_ADUTUX is not set
> ++# CONFIG_USB_SEVSEG is not set
> ++# CONFIG_USB_RIO500 is not set
> ++# CONFIG_USB_LEGOTOWER is not set
> ++# CONFIG_USB_LCD is not set
> ++# CONFIG_USB_LED is not set
> ++# CONFIG_USB_CYPRESS_CY7C63 is not set
> ++# CONFIG_USB_CYTHERM is not set
> ++# CONFIG_USB_IDMOUSE is not set
> ++# CONFIG_USB_FTDI_ELAN is not set
> ++# CONFIG_USB_APPLEDISPLAY is not set
> ++# CONFIG_USB_SISUSBVGA is not set
> ++# CONFIG_USB_LD is not set
> ++# CONFIG_USB_TRANCEVIBRATOR is not set
> ++# CONFIG_USB_IOWARRIOR is not set
> ++# CONFIG_USB_TEST is not set
> ++# CONFIG_USB_ISIGHTFW is not set
> ++# CONFIG_USB_YUREX is not set
> ++CONFIG_USB_GADGET=y
> ++# CONFIG_USB_GADGET_DEBUG_FILES is not set
> ++CONFIG_USB_GADGET_VBUS_DRAW=100
> ++CONFIG_USB_GADGET_SELECTED=y
> ++CONFIG_USB_GADGET_ARC=y
> ++# CONFIG_IMX_USB_CHARGER is not set
> ++CONFIG_USB_ARC=y
> ++# CONFIG_USB_GADGET_FSL_USB2 is not set
> ++# CONFIG_USB_GADGET_FUSB300 is not set
> ++# CONFIG_USB_GADGET_R8A66597 is not set
> ++# CONFIG_USB_GADGET_PXA_U2O is not set
> ++# CONFIG_USB_GADGET_M66592 is not set
> ++# CONFIG_USB_GADGET_DUMMY_HCD is not set
> ++CONFIG_USB_GADGET_DUALSPEED=y
> ++# CONFIG_USB_ZERO is not set
> ++# CONFIG_USB_AUDIO is not set
> ++# CONFIG_USB_ETH is not set
> ++# CONFIG_USB_G_NCM is not set
> ++# CONFIG_USB_GADGETFS is not set
> ++# CONFIG_USB_FUNCTIONFS is not set
> ++# CONFIG_USB_FILE_STORAGE is not set
> ++CONFIG_USB_MASS_STORAGE=y
> ++# CONFIG_USB_G_SERIAL is not set
> ++# CONFIG_USB_MIDI_GADGET is not set
> ++# CONFIG_USB_G_PRINTER is not set
> ++# CONFIG_USB_G_ANDROID is not set
> ++# CONFIG_USB_CDC_COMPOSITE is not set
> ++# CONFIG_USB_G_MULTI is not set
> ++# CONFIG_USB_G_HID is not set
> ++# CONFIG_USB_G_DBGP is not set
> ++# CONFIG_USB_G_WEBCAM is not set
> ++
> ++#
> ++# OTG and related infrastructure
> ++#
> ++CONFIG_USB_OTG_UTILS=y
> ++CONFIG_USB_GPIO_VBUS=y
> ++CONFIG_USB_ULPI=y
> ++# CONFIG_NOP_USB_XCEIV is not set
> ++# CONFIG_MXC_OTG is not set
> ++CONFIG_MMC=y
> ++# CONFIG_MMC_DEBUG is not set
> ++CONFIG_MMC_UNSAFE_RESUME=y
> ++CONFIG_MMC_CLKGATE=y
> ++# CONFIG_MMC_EMBEDDED_SDIO is not set
> ++# CONFIG_MMC_PARANOID_SD_INIT is not set
> ++
> ++#
> ++# MMC/SD/SDIO Card Drivers
> ++#
> ++CONFIG_MMC_BLOCK=y
> ++CONFIG_MMC_BLOCK_MINORS=8
> ++CONFIG_MMC_BLOCK_BOUNCE=y
> ++# CONFIG_MMC_BLOCK_DEFERRED_RESUME is not set
> ++# CONFIG_SDIO_UART is not set
> ++# CONFIG_MMC_TEST is not set
> ++
> ++#
> ++# MMC/SD/SDIO Host Controller Drivers
> ++#
> ++# CONFIG_MMC_ARMMMCI is not set
> ++CONFIG_MMC_SDHCI=y
> ++CONFIG_MMC_SDHCI_IO_ACCESSORS=y
> ++CONFIG_MMC_SDHCI_PLTFM=y
> ++CONFIG_MMC_SDHCI_ESDHC_IMX=y
> ++# CONFIG_MMC_DW is not set
> ++# CONFIG_MMC_VUB300 is not set
> ++# CONFIG_MMC_USHC is not set
> ++# CONFIG_MEMSTICK is not set
> ++# CONFIG_NEW_LEDS is not set
> ++# CONFIG_NFC_DEVICES is not set
> ++CONFIG_SWITCH=y
> ++# CONFIG_SWITCH_GPIO is not set
> ++# CONFIG_ACCESSIBILITY is not set
> ++CONFIG_RTC_LIB=y
> ++# CONFIG_RTC_CLASS is not set
> ++CONFIG_DMADEVICES=y
> ++# CONFIG_DMADEVICES_DEBUG is not set
> ++
> ++#
> ++# DMA Devices
> ++#
> ++# CONFIG_AMBA_PL08X is not set
> ++# CONFIG_DW_DMAC is not set
> ++# CONFIG_MXC_PXP_V2 is not set
> ++# CONFIG_TIMB_DMA is not set
> ++CONFIG_IMX_SDMA=y
> ++# CONFIG_MXS_DMA is not set
> ++CONFIG_DMA_ENGINE=y
> ++
> ++#
> ++# DMA Clients
> ++#
> ++# CONFIG_NET_DMA is not set
> ++# CONFIG_ASYNC_TX_DMA is not set
> ++# CONFIG_DMATEST is not set
> ++# CONFIG_AUXDISPLAY is not set
> ++# CONFIG_UIO is not set
> ++CONFIG_STAGING=y
> ++# CONFIG_USBIP_CORE is not set
> ++# CONFIG_PRISM2_USB is not set
> ++# CONFIG_ECHO is not set
> ++# CONFIG_ASUS_OLED is not set
> ++# CONFIG_R8712U is not set
> ++# CONFIG_TRANZPORT is not set
> ++
> ++#
> ++# Android
> ++#
> ++# CONFIG_ANDROID is not set
> ++# CONFIG_POHMELFS is not set
> ++# CONFIG_LINE6_USB is not set
> ++# CONFIG_VT6656 is not set
> ++# CONFIG_IIO is not set
> ++# CONFIG_XVMALLOC is not set
> ++# CONFIG_ZRAM is not set
> ++# CONFIG_FB_SM7XX is not set
> ++# CONFIG_EASYCAP is not set
> ++CONFIG_MACH_NO_WESTBRIDGE=y
> ++# CONFIG_ATH6K_LEGACY is not set
> ++# CONFIG_USB_ENESTORAGE is not set
> ++# CONFIG_BCM_WIMAX is not set
> ++# CONFIG_FT1000 is not set
> ++
> ++#
> ++# Speakup console speech
> ++#
> ++# CONFIG_SPEAKUP is not set
> ++# CONFIG_TOUCHSCREEN_CLEARPAD_TM1217 is not set
> ++# CONFIG_TOUCHSCREEN_SYNAPTICS_I2C_RMI4 is not set
> ++
> ++#
> ++# Altera FPGA firmware download module
> ++#
> ++# CONFIG_ALTERA_STAPL is not set
> ++CONFIG_CLKDEV_LOOKUP=y
> ++CONFIG_CLKSRC_MMIO=y
> ++
> ++#
> ++# MXC support drivers
> ++#
> ++CONFIG_MXC_IPU=y
> ++CONFIG_MXC_IPU_V3=y
> ++CONFIG_MXC_IPU_V3H=y
> ++
> ++#
> ++# MXC SSI support
> ++#
> ++CONFIG_MXC_SSI=y
> ++
> ++#
> ++# MXC Digital Audio Multiplexer support
> ++#
> ++# CONFIG_MXC_DAM is not set
> ++
> ++#
> ++# MXC PMIC support
> ++#
> ++# CONFIG_MXC_PMIC_MC13783 is not set
> ++# CONFIG_MXC_PMIC_MC13892 is not set
> ++# CONFIG_MXC_PMIC_MC34704 is not set
> ++# CONFIG_MXC_PMIC_MC9SDZ60 is not set
> ++# CONFIG_MXC_PMIC_MC9S08DZ60 is not set
> ++
> ++#
> ++# MXC Security Drivers
> ++#
> ++# CONFIG_MXC_SECURITY_SCC is not set
> ++# CONFIG_MXC_SECURITY_RNG is not set
> ++
> ++#
> ++# MXC MPEG4 Encoder Kernel module support
> ++#
> ++# CONFIG_MXC_HMP4E is not set
> ++
> ++#
> ++# MXC HARDWARE EVENT
> ++#
> ++# CONFIG_MXC_HWEVENT is not set
> ++
> ++#
> ++# MXC VPU(Video Processing Unit) support
> ++#
> ++CONFIG_MXC_VPU=y
> ++# CONFIG_MXC_VPU_DEBUG is not set
> ++# CONFIG_MX6_VPU_352M is not set
> ++
> ++#
> ++# MXC Asynchronous Sample Rate Converter support
> ++#
> ++CONFIG_MXC_ASRC=y
> ++
> ++#
> ++# MXC Bluetooth support
> ++#
> ++
> ++#
> ++# Broadcom GPS ioctrl support
> ++#
> ++
> ++#
> ++# MXC Media Local Bus Driver
> ++#
> ++# CONFIG_MXC_MLB150 is not set
> ++
> ++#
> ++# i.MX ADC support
> ++#
> ++# CONFIG_IMX_ADC is not set
> ++
> ++#
> ++# MXC Vivante GPU support
> ++#
> ++CONFIG_MXC_GPU_VIV=y
> ++
> ++#
> ++# ANATOP_THERMAL
> ++#
> ++CONFIG_ANATOP_THERMAL=y
> ++
> ++#
> ++# MXC MIPI Support
> ++#
> ++# CONFIG_MXC_MIPI_CSI2 is not set
> ++
> ++#
> ++# MXC HDMI CEC (Consumer Electronics Control) support
> ++#
> ++# CONFIG_MXC_HDMI_CEC is not set
> ++
> ++#
> ++# File systems
> ++#
> ++CONFIG_EXT2_FS=y
> ++# CONFIG_EXT2_FS_XATTR is not set
> ++# CONFIG_EXT2_FS_XIP is not set
> ++CONFIG_EXT3_FS=y
> ++# CONFIG_EXT3_DEFAULTS_TO_ORDERED is not set
> ++# CONFIG_EXT3_FS_XATTR is not set
> ++# CONFIG_EXT4_FS is not set
> ++CONFIG_JBD=y
> ++# CONFIG_REISERFS_FS is not set
> ++# CONFIG_JFS_FS is not set
> ++# CONFIG_XFS_FS is not set
> ++# CONFIG_BTRFS_FS is not set
> ++# CONFIG_NILFS2_FS is not set
> ++# CONFIG_FS_POSIX_ACL is not set
> ++CONFIG_FILE_LOCKING=y
> ++CONFIG_FSNOTIFY=y
> ++# CONFIG_DNOTIFY is not set
> ++CONFIG_INOTIFY_USER=y
> ++# CONFIG_FANOTIFY is not set
> ++# CONFIG_QUOTA is not set
> ++# CONFIG_QUOTACTL is not set
> ++# CONFIG_AUTOFS4_FS is not set
> ++# CONFIG_FUSE_FS is not set
> ++
> ++#
> ++# Caches
> ++#
> ++# CONFIG_FSCACHE is not set
> ++
> ++#
> ++# CD-ROM/DVD Filesystems
> ++#
> ++# CONFIG_ISO9660_FS is not set
> ++# CONFIG_UDF_FS is not set
> ++
> ++#
> ++# DOS/FAT/NT Filesystems
> ++#
> ++CONFIG_FAT_FS=y
> ++# CONFIG_MSDOS_FS is not set
> ++CONFIG_VFAT_FS=y
> ++CONFIG_FAT_DEFAULT_CODEPAGE=437
> ++CONFIG_FAT_DEFAULT_IOCHARSET="iso8859-1"
> ++# CONFIG_NTFS_FS is not set
> ++
> ++#
> ++# Pseudo filesystems
> ++#
> ++CONFIG_PROC_FS=y
> ++CONFIG_PROC_SYSCTL=y
> ++# CONFIG_PROC_PAGE_MONITOR is not set
> ++CONFIG_SYSFS=y
> ++# CONFIG_HUGETLB_PAGE is not set
> ++# CONFIG_CONFIGFS_FS is not set
> ++# CONFIG_MISC_FILESYSTEMS is not set
> ++# CONFIG_NETWORK_FILESYSTEMS is not set
> ++
> ++#
> ++# Partition Types
> ++#
> ++CONFIG_PARTITION_ADVANCED=y
> ++# CONFIG_ACORN_PARTITION is not set
> ++# CONFIG_OSF_PARTITION is not set
> ++# CONFIG_AMIGA_PARTITION is not set
> ++# CONFIG_ATARI_PARTITION is not set
> ++# CONFIG_MAC_PARTITION is not set
> ++CONFIG_MSDOS_PARTITION=y
> ++# CONFIG_BSD_DISKLABEL is not set
> ++# CONFIG_MINIX_SUBPARTITION is not set
> ++# CONFIG_SOLARIS_X86_PARTITION is not set
> ++# CONFIG_UNIXWARE_DISKLABEL is not set
> ++# CONFIG_LDM_PARTITION is not set
> ++# CONFIG_SGI_PARTITION is not set
> ++# CONFIG_ULTRIX_PARTITION is not set
> ++# CONFIG_SUN_PARTITION is not set
> ++# CONFIG_KARMA_PARTITION is not set
> ++CONFIG_EFI_PARTITION=y
> ++# CONFIG_SYSV68_PARTITION is not set
> ++CONFIG_NLS=y
> ++CONFIG_NLS_DEFAULT="iso8859-1"
> ++CONFIG_NLS_CODEPAGE_437=y
> ++# CONFIG_NLS_CODEPAGE_737 is not set
> ++# CONFIG_NLS_CODEPAGE_775 is not set
> ++# CONFIG_NLS_CODEPAGE_850 is not set
> ++# CONFIG_NLS_CODEPAGE_852 is not set
> ++# CONFIG_NLS_CODEPAGE_855 is not set
> ++# CONFIG_NLS_CODEPAGE_857 is not set
> ++# CONFIG_NLS_CODEPAGE_860 is not set
> ++# CONFIG_NLS_CODEPAGE_861 is not set
> ++# CONFIG_NLS_CODEPAGE_862 is not set
> ++# CONFIG_NLS_CODEPAGE_863 is not set
> ++# CONFIG_NLS_CODEPAGE_864 is not set
> ++# CONFIG_NLS_CODEPAGE_865 is not set
> ++# CONFIG_NLS_CODEPAGE_866 is not set
> ++# CONFIG_NLS_CODEPAGE_869 is not set
> ++# CONFIG_NLS_CODEPAGE_936 is not set
> ++# CONFIG_NLS_CODEPAGE_950 is not set
> ++# CONFIG_NLS_CODEPAGE_932 is not set
> ++# CONFIG_NLS_CODEPAGE_949 is not set
> ++# CONFIG_NLS_CODEPAGE_874 is not set
> ++# CONFIG_NLS_ISO8859_8 is not set
> ++# CONFIG_NLS_CODEPAGE_1250 is not set
> ++# CONFIG_NLS_CODEPAGE_1251 is not set
> ++# CONFIG_NLS_ASCII is not set
> ++CONFIG_NLS_ISO8859_1=y
> ++# CONFIG_NLS_ISO8859_2 is not set
> ++# CONFIG_NLS_ISO8859_3 is not set
> ++# CONFIG_NLS_ISO8859_4 is not set
> ++# CONFIG_NLS_ISO8859_5 is not set
> ++# CONFIG_NLS_ISO8859_6 is not set
> ++# CONFIG_NLS_ISO8859_7 is not set
> ++# CONFIG_NLS_ISO8859_9 is not set
> ++# CONFIG_NLS_ISO8859_13 is not set
> ++# CONFIG_NLS_ISO8859_14 is not set
> ++# CONFIG_NLS_ISO8859_15 is not set
> ++# CONFIG_NLS_KOI8_R is not set
> ++# CONFIG_NLS_KOI8_U is not set
> ++# CONFIG_NLS_UTF8 is not set
> ++
> ++#
> ++# Kernel hacking
> ++#
> ++CONFIG_PRINTK_TIME=y
> ++CONFIG_DEFAULT_MESSAGE_LOGLEVEL=4
> ++CONFIG_ENABLE_WARN_DEPRECATED=y
> ++CONFIG_ENABLE_MUST_CHECK=y
> ++CONFIG_FRAME_WARN=4096
> ++# CONFIG_MAGIC_SYSRQ is not set
> ++CONFIG_STRIP_ASM_SYMS=y
> ++# CONFIG_UNUSED_SYMBOLS is not set
> ++# CONFIG_DEBUG_FS is not set
> ++# CONFIG_HEADERS_CHECK is not set
> ++# CONFIG_DEBUG_SECTION_MISMATCH is not set
> ++# CONFIG_DEBUG_KERNEL is not set
> ++# CONFIG_HARDLOCKUP_DETECTOR is not set
> ++# CONFIG_SLUB_STATS is not set
> ++# CONFIG_SPARSE_RCU_POINTER is not set
> ++CONFIG_STACKTRACE=y
> ++# CONFIG_DEBUG_MEMORY_INIT is not set
> ++CONFIG_FRAME_POINTER=y
> ++CONFIG_RCU_CPU_STALL_TIMEOUT=60
> ++CONFIG_RCU_CPU_STALL_VERBOSE=y
> ++CONFIG_SYSCTL_SYSCALL_CHECK=y
> ++CONFIG_HAVE_FUNCTION_TRACER=y
> ++CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y
> ++CONFIG_HAVE_DYNAMIC_FTRACE=y
> ++CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y
> ++CONFIG_HAVE_C_RECORDMCOUNT=y
> ++CONFIG_TRACING_SUPPORT=y
> ++# CONFIG_FTRACE is not set
> ++# CONFIG_DMA_API_DEBUG is not set
> ++# CONFIG_ATOMIC64_SELFTEST is not set
> ++# CONFIG_SAMPLES is not set
> ++CONFIG_HAVE_ARCH_KGDB=y
> ++# CONFIG_TEST_KSTRTOX is not set
> ++# CONFIG_STRICT_DEVMEM is not set
> ++# CONFIG_ARM_UNWIND is not set
> ++# CONFIG_DEBUG_USER is not set
> ++CONFIG_OC_ETM=y
> ++
> ++#
> ++# Security options
> ++#
> ++# CONFIG_KEYS is not set
> ++# CONFIG_SECURITY_DMESG_RESTRICT is not set
> ++# CONFIG_SECURITY is not set
> ++# CONFIG_SECURITYFS is not set
> ++CONFIG_DEFAULT_SECURITY_DAC=y
> ++CONFIG_DEFAULT_SECURITY=""
> ++CONFIG_CRYPTO=y
> ++
> ++#
> ++# Crypto core or helper
> ++#
> ++CONFIG_CRYPTO_ALGAPI=y
> ++CONFIG_CRYPTO_ALGAPI2=y
> ++CONFIG_CRYPTO_AEAD2=y
> ++CONFIG_CRYPTO_BLKCIPHER=y
> ++CONFIG_CRYPTO_BLKCIPHER2=y
> ++CONFIG_CRYPTO_HASH2=y
> ++CONFIG_CRYPTO_RNG2=y
> ++CONFIG_CRYPTO_PCOMP2=y
> ++CONFIG_CRYPTO_MANAGER=y
> ++CONFIG_CRYPTO_MANAGER2=y
> ++CONFIG_CRYPTO_MANAGER_DISABLE_TESTS=y
> ++# CONFIG_CRYPTO_GF128MUL is not set
> ++# CONFIG_CRYPTO_NULL is not set
> ++# CONFIG_CRYPTO_PCRYPT is not set
> ++CONFIG_CRYPTO_WORKQUEUE=y
> ++# CONFIG_CRYPTO_CRYPTD is not set
> ++# CONFIG_CRYPTO_AUTHENC is not set
> ++# CONFIG_CRYPTO_TEST is not set
> ++# CONFIG_CRYPTO_CRYPTODEV is not set
> ++
> ++#
> ++# Authenticated Encryption with Associated Data
> ++#
> ++# CONFIG_CRYPTO_CCM is not set
> ++# CONFIG_CRYPTO_GCM is not set
> ++# CONFIG_CRYPTO_SEQIV is not set
> ++
> ++#
> ++# Block modes
> ++#
> ++# CONFIG_CRYPTO_CBC is not set
> ++# CONFIG_CRYPTO_CTR is not set
> ++# CONFIG_CRYPTO_CTS is not set
> ++CONFIG_CRYPTO_ECB=y
> ++# CONFIG_CRYPTO_LRW is not set
> ++# CONFIG_CRYPTO_PCBC is not set
> ++# CONFIG_CRYPTO_XTS is not set
> ++
> ++#
> ++# Hash modes
> ++#
> ++# CONFIG_CRYPTO_HMAC is not set
> ++# CONFIG_CRYPTO_XCBC is not set
> ++# CONFIG_CRYPTO_VMAC is not set
> ++
> ++#
> ++# Digest
> ++#
> ++# CONFIG_CRYPTO_CRC32C is not set
> ++# CONFIG_CRYPTO_GHASH is not set
> ++# CONFIG_CRYPTO_MD4 is not set
> ++# CONFIG_CRYPTO_MD5 is not set
> ++# CONFIG_CRYPTO_MICHAEL_MIC is not set
> ++# CONFIG_CRYPTO_RMD128 is not set
> ++# CONFIG_CRYPTO_RMD160 is not set
> ++# CONFIG_CRYPTO_RMD256 is not set
> ++# CONFIG_CRYPTO_RMD320 is not set
> ++# CONFIG_CRYPTO_SHA1 is not set
> ++# CONFIG_CRYPTO_SHA256 is not set
> ++# CONFIG_CRYPTO_SHA512 is not set
> ++# CONFIG_CRYPTO_TGR192 is not set
> ++# CONFIG_CRYPTO_WP512 is not set
> ++
> ++#
> ++# Ciphers
> ++#
> ++CONFIG_CRYPTO_AES=y
> ++# CONFIG_CRYPTO_ANUBIS is not set
> ++# CONFIG_CRYPTO_ARC4 is not set
> ++# CONFIG_CRYPTO_BLOWFISH is not set
> ++# CONFIG_CRYPTO_CAMELLIA is not set
> ++# CONFIG_CRYPTO_CAST5 is not set
> ++# CONFIG_CRYPTO_CAST6 is not set
> ++# CONFIG_CRYPTO_DES is not set
> ++# CONFIG_CRYPTO_FCRYPT is not set
> ++# CONFIG_CRYPTO_KHAZAD is not set
> ++# CONFIG_CRYPTO_SALSA20 is not set
> ++# CONFIG_CRYPTO_SEED is not set
> ++# CONFIG_CRYPTO_SERPENT is not set
> ++# CONFIG_CRYPTO_TEA is not set
> ++# CONFIG_CRYPTO_TWOFISH is not set
> ++
> ++#
> ++# Compression
> ++#
> ++# CONFIG_CRYPTO_DEFLATE is not set
> ++# CONFIG_CRYPTO_ZLIB is not set
> ++# CONFIG_CRYPTO_LZO is not set
> ++
> ++#
> ++# Random Number Generation
> ++#
> ++# CONFIG_CRYPTO_ANSI_CPRNG is not set
> ++# CONFIG_CRYPTO_USER_API_HASH is not set
> ++# CONFIG_CRYPTO_USER_API_SKCIPHER is not set
> ++# CONFIG_CRYPTO_HW is not set
> ++# CONFIG_BINARY_PRINTF is not set
> ++
> ++#
> ++# Library routines
> ++#
> ++CONFIG_BITREVERSE=y
> ++CONFIG_RATIONAL=y
> ++# CONFIG_CRC_CCITT is not set
> ++CONFIG_CRC16=y
> ++# CONFIG_CRC_T10DIF is not set
> ++# CONFIG_CRC_ITU_T is not set
> ++CONFIG_CRC32=y
> ++# CONFIG_CRC7 is not set
> ++# CONFIG_LIBCRC32C is not set
> ++# CONFIG_XZ_DEC is not set
> ++# CONFIG_XZ_DEC_BCJ is not set
> ++CONFIG_GENERIC_ALLOCATOR=y
> ++CONFIG_HAS_IOMEM=y
> ++CONFIG_HAS_IOPORT=y
> ++CONFIG_HAS_DMA=y
> ++CONFIG_CPU_RMAP=y
> ++CONFIG_NLATTR=y
> ++# CONFIG_AVERAGE is not set
> +diff --git a/arch/arm/mach-mx6/Kconfig b/arch/arm/mach-mx6/Kconfig
> +index 2ffd90d..e49c56f 100644
> +--- a/arch/arm/mach-mx6/Kconfig
> ++++ b/arch/arm/mach-mx6/Kconfig
> +@@ -251,6 +251,47 @@ config MACH_MX6Q_SABREAUTO
> + Include support for i.MX 6Quad SABRE Auto platform. This includes specific
> + configurations for the board and its peripherals.
> +
> ++config MACH_WANDBOARD
> ++ bool "Support for the WandBoard"
> ++ select ARCH_MX6Q
> ++ select SOC_IMX6Q
> ++ select IMX_HAVE_PLATFORM_DMA if IMX_SDMA
> ++ select IMX_HAVE_PLATFORM_IMX_UART if SERIAL_IMX
> ++ select IMX_HAVE_PLATFORM_SDHCI_ESDHC_IMX if MMC_SDHCI_ESDHC_IMX
> ++ select IMX_HAVE_PLATFORM_IMX_I2C if I2C_IMX
> ++ select IMX_HAVE_PLATFORM_IMX_ASRC if SND_IMX_SOC
> ++ select ARCH_MXC_AUDMUX_V2 if SND_IMX_SOC
> ++ select IMX_HAVE_PLATFORM_IMX_SSI if MXC_SSI
> ++ select IMX_HAVE_PLATFORM_IMX_ESAI if MXC_SSI
> ++ select IMX_HAVE_PLATFORM_IMX_SPDIF if SND_SOC_IMX_SPDIF
> ++ select IMX_HAVE_PLATFORM_FEC if NETDEVICES
> ++ select IMX_HAVE_PLATFORM_FSL_USB2_UDC if USB
> ++ select IMX_HAVE_PLATFORM_MXC_EHCI if USB
> ++ select IMX_HAVE_PLATFORM_FSL_USB_WAKEUP if USB
> ++ select IMX_HAVE_PLATFORM_FSL_OTG if USB_OTG
> ++ select IMX_HAVE_PLATFORM_MXC_HDMI if FB_MXC_HDMI
> ++ select IMX_HAVE_PLATFORM_IMX_IPUV3 if MXC_IPU_V3
> ++ select IMX_HAVE_PLATFORM_IMX_ANATOP_THERMAL if ANATOP_THERMAL
> ++ select IMX_HAVE_PLATFORM_IMX_PM if PM
> ++ select IMX_HAVE_PLATFORM_IMX_DVFS if CPU_FREQ_IMX
> ++ select IMX_HAVE_PLATFORM_SPI_IMX if SPI
> ++ select IMX_HAVE_PLATFORM_VIV_GPU if MXC_GPU_VIV
> ++ select IMX_HAVE_PLATFORM_IMX_VPU if MXC_VPU
> ++ select IMX_HAVE_PLATFORM_IMX_MIPI_DSI if VIDEO_MXC_IPU_OUTPUT
> ++ help
> ++ Include support for the WandBoard SoM.
> ++
> ++
> ++config WANDBOARD_BASE
> ++ tristate "Support for Wand baseboard"
> ++ depends on MACH_WANDBOARD
> ++ default y
> ++ help
> ++ Include support for the devices on the default wand baseboard.
> ++
> ++ If you have a standard Wandboard, say Y.
> ++
> ++
> + comment "MX6 Options:"
> +
> + config IMX_PCIE
> +diff --git a/arch/arm/mach-mx6/Makefile b/arch/arm/mach-mx6/Makefile
> +index 5cac9bc..3f43098 100644
> +--- a/arch/arm/mach-mx6/Makefile
> ++++ b/arch/arm/mach-mx6/Makefile
> +@@ -14,6 +14,8 @@ obj-$(CONFIG_MACH_MX6SL_EVK) += board-mx6sl_evk.o mx6sl_evk_pmic_pfuze100.o
> + obj-$(CONFIG_MACH_MX6Q_SABRELITE) += board-mx6q_sabrelite.o
> + obj-$(CONFIG_MACH_MX6Q_SABRESD) += board-mx6q_sabresd.o mx6q_sabresd_pmic_pfuze100.o
> + obj-$(CONFIG_MACH_MX6Q_SABREAUTO) += board-mx6q_sabreauto.o mx6q_sabreauto_pmic_pfuze100.o
> ++obj-$(CONFIG_MACH_WANDBOARD) += board-wand.o
> ++obj-$(CONFIG_WANDBOARD_BASE) += baseboard-wand.o
> + obj-$(CONFIG_SMP) += plat_hotplug.o platsmp.o headsmp.o
> + obj-$(CONFIG_LOCAL_TIMERS) += localtimer.o
> + obj-$(CONFIG_IMX_PCIE) += pcie.o
> +diff --git a/arch/arm/mach-mx6/baseboard-wand.c b/arch/arm/mach-mx6/baseboard-wand.c
> +new file mode 100644
> +index 0000000..e9e9378
> +--- /dev/null
> ++++ b/arch/arm/mach-mx6/baseboard-wand.c
> +@@ -0,0 +1,137 @@
> ++
> ++#include <asm/mach/arch.h>
> ++
> ++#include <linux/clk.h>
> ++#include <linux/i2c.h>
> ++#include <linux/platform_device.h>
> ++#include <linux/regulator/fixed.h>
> ++#include <linux/regulator/machine.h>
> ++
> ++#include <mach/common.h>
> ++#include <mach/devices-common.h>
> ++
> ++
> ++/****************************************************************************
> ++ *
> ++ * SGTL5000 Audio Codec
> ++ *
> ++ ****************************************************************************/
> ++
> ++static struct regulator_consumer_supply wandbase_sgtl5000_consumer_vdda = {
> ++ .supply = "VDDA",
> ++ .dev_name = "0-000a", /* Modified load time */
> ++};
> ++
> ++/* ------------------------------------------------------------------------ */
> ++
> ++static struct regulator_consumer_supply wandbase_sgtl5000_consumer_vddio = {
> ++ .supply = "VDDIO",
> ++ .dev_name = "0-000a", /* Modified load time */
> ++};
> ++
> ++/* ------------------------------------------------------------------------ */
> ++
> ++static struct regulator_init_data wandbase_sgtl5000_vdda_reg_initdata = {
> ++ .num_consumer_supplies = 1,
> ++ .consumer_supplies = &wandbase_sgtl5000_consumer_vdda,
> ++};
> ++
> ++/* ------------------------------------------------------------------------ */
> ++
> ++static struct regulator_init_data wandbase_sgtl5000_vddio_reg_initdata = {
> ++ .num_consumer_supplies = 1,
> ++ .consumer_supplies = &wandbase_sgtl5000_consumer_vddio,
> ++};
> ++
> ++/* ------------------------------------------------------------------------ */
> ++
> ++static struct fixed_voltage_config wandbase_sgtl5000_vdda_reg_config = {
> ++ .supply_name = "VDDA",
> ++ .microvolts = 2500000,
> ++ .gpio = -1,
> ++ .init_data = &wandbase_sgtl5000_vdda_reg_initdata,
> ++};
> ++
> ++/* ------------------------------------------------------------------------ */
> ++
> ++static struct fixed_voltage_config wandbase_sgtl5000_vddio_reg_config = {
> ++ .supply_name = "VDDIO",
> ++ .microvolts = 3300000,
> ++ .gpio = -1,
> ++ .init_data = &wandbase_sgtl5000_vddio_reg_initdata,
> ++};
> ++
> ++/* ------------------------------------------------------------------------ */
> ++
> ++static struct platform_device wandbase_sgtl5000_vdda_reg_devices = {
> ++ .name = "reg-fixed-voltage",
> ++ .id = 0,
> ++ .dev = {
> ++ .platform_data = &wandbase_sgtl5000_vdda_reg_config,
> ++ },
> ++};
> ++
> ++/* ------------------------------------------------------------------------ */
> ++
> ++static struct platform_device wandbase_sgtl5000_vddio_reg_devices = {
> ++ .name = "reg-fixed-voltage",
> ++ .id = 1,
> ++ .dev = {
> ++ .platform_data = &wandbase_sgtl5000_vddio_reg_config,
> ++ },
> ++};
> ++
> ++/* ------------------------------------------------------------------------ */
> ++
> ++static struct platform_device wandbase_audio_device = {
> ++ .name = "imx-sgtl5000",
> ++};
> ++
> ++/* ------------------------------------------------------------------------ */
> ++
> ++static const struct i2c_board_info wandbase_sgtl5000_i2c_data __initdata = {
> ++ I2C_BOARD_INFO("sgtl5000", 0x0a)
> ++};
> ++
> ++/* ------------------------------------------------------------------------ */
> ++
> ++static char wandbase_sgtl5000_dev_name[8] = "0-000a";
> ++
> ++extern struct mxc_audio_platform_data wand_audio_channel_data;
> ++
> ++static __init int wandbase_init_sgtl5000(void) {
> ++ int i2c_bus = 1; /* TODO: get this from the module. */
> ++
> ++ wandbase_sgtl5000_dev_name[0] = '0' + i2c_bus;
> ++ wandbase_sgtl5000_consumer_vdda.dev_name = wandbase_sgtl5000_dev_name;
> ++ wandbase_sgtl5000_consumer_vddio.dev_name = wandbase_sgtl5000_dev_name;
> ++
> ++ wandbase_audio_device.dev.platform_data = &wand_audio_channel_data;
> ++ platform_device_register(&wandbase_audio_device);
> ++
> ++ i2c_register_board_info(i2c_bus, &wandbase_sgtl5000_i2c_data, 1);
> ++ platform_device_register(&wandbase_sgtl5000_vdda_reg_devices);
> ++ platform_device_register(&wandbase_sgtl5000_vddio_reg_devices);
> ++ return 0;
> ++}
> ++
> ++
> ++/****************************************************************************
> ++ *
> ++ * main-function for wand baseboard
> ++ *
> ++ ****************************************************************************/
> ++
> ++static __init int wandbase_init(void) {
> ++ return wandbase_init_sgtl5000();
> ++}
> ++subsys_initcall(wandbase_init);
> ++
> ++static __exit void wandbase_exit(void) {
> ++ /* Actually, this cannot be unloaded. Or loaded as a module..? */
> ++}
> ++module_exit(wandbase_exit);
> ++
> ++MODULE_DESCRIPTION("Wand baseboard driver");
> ++MODULE_AUTHOR("Tapani <tapani at vmail.me>");
> ++MODULE_LICENSE("GPL");
> +diff --git a/arch/arm/mach-mx6/board-wand.c b/arch/arm/mach-mx6/board-wand.c
> +new file mode 100644
> +index 0000000..7f972eb
> +--- /dev/null
> ++++ b/arch/arm/mach-mx6/board-wand.c
> +@@ -0,0 +1,972 @@
> ++
> ++#include <asm/mach-types.h>
> ++#include <asm/mach/arch.h>
> ++#include <asm/mach/time.h>
> ++
> ++#include <linux/clk.h>
> ++#include <linux/delay.h>
> ++#include <linux/err.h>
> ++#include <linux/fec.h>
> ++#include <linux/i2c.h>
> ++#include <linux/kernel.h>
> ++#include <linux/memblock.h>
> ++#include <linux/phy.h>
> ++
> ++#include <mach/common.h>
> ++//#include <mach/devices-common.h>
> ++#include <mach/gpio.h>
> ++#include <mach/iomux-mx6dl.h>
> ++#include <mach/iomux-v3.h>
> ++#include <mach/mx6.h>
> ++
> ++#include "crm_regs.h"
> ++#include "devices-imx6q.h"
> ++#include "usb.h"
> ++//#include "cpu_op-mx6.h"
> ++
> ++#define WAND_BT_ON IMX_GPIO_NR(3, 13)
> ++#define WAND_BT_WAKE IMX_GPIO_NR(3, 14)
> ++#define WAND_BT_HOST_WAKE IMX_GPIO_NR(3, 15)
> ++
> ++#define WAND_RGMII_INT IMX_GPIO_NR(1, 28)
> ++#define WAND_RGMII_RST IMX_GPIO_NR(3, 29)
> ++
> ++#define WAND_SD1_CD IMX_GPIO_NR(1, 2)
> ++#define WAND_SD3_CD IMX_GPIO_NR(3, 9)
> ++#define WAND_SD3_WP IMX_GPIO_NR(1, 10)
> ++
> ++#define WAND_USB_OTG_OC IMX_GPIO_NR(1, 9)
> ++#define WAND_USB_OTG_PWR IMX_GPIO_NR(3, 22)
> ++#define WAND_USB_H1_OC IMX_GPIO_NR(3, 30)
> ++
> ++#define WAND_WL_REF_ON IMX_GPIO_NR(2, 29)
> ++#define WAND_WL_RST_N IMX_GPIO_NR(5, 2)
> ++#define WAND_WL_REG_ON IMX_GPIO_NR(1, 26)
> ++#define WAND_WL_HOST_WAKE IMX_GPIO_NR(1, 29)
> ++#define WAND_WL_WAKE IMX_GPIO_NR(1, 30)
> ++
> ++/* Syntactic sugar for pad configuration */
> ++#define WAND_SETUP_PADS(p) \
> ++ mxc_iomux_v3_setup_multiple_pads((p), ARRAY_SIZE(p))
> ++
> ++/* See arch/arm/plat-mxc/include/mach/iomux-mx6dl.h for definitions */
> ++
> ++/****************************************************************************
> ++ *
> ++ * DMA controller init
> ++ *
> ++ ****************************************************************************/
> ++
> ++static __init void wand_init_dma(void) {
> ++ imx6q_add_dma();
> ++}
> ++
> ++
> ++/****************************************************************************
> ++ *
> ++ * SD init
> ++ *
> ++ * SD1 is routed to EDM connector (external SD on wand baseboard)
> ++ * SD2 is WiFi
> ++ * SD3 is boot SD on the module
> ++ *
> ++ ****************************************************************************/
> ++
> ++/* For some reason, iomux_mx6dl.h does not define multiple speeds for
> ++ SD1 and SD2, so these don't have any speed switching. */
> ++static iomux_v3_cfg_t mx6dl_sd1_pads[] = {
> ++ MX6DL_PAD_SD1_CLK__USDHC1_CLK_50MHZ_40OHM,
> ++ MX6DL_PAD_SD1_CMD__USDHC1_CMD_50MHZ_40OHM,
> ++ MX6DL_PAD_SD1_DAT0__USDHC1_DAT0_50MHZ_40OHM,
> ++ MX6DL_PAD_SD1_DAT1__USDHC1_DAT1_50MHZ_40OHM,
> ++ MX6DL_PAD_SD1_DAT2__USDHC1_DAT2_50MHZ_40OHM,
> ++ MX6DL_PAD_SD1_DAT3__USDHC1_DAT3_50MHZ_40OHM,
> ++};
> ++
> ++static iomux_v3_cfg_t mx6dl_sd2_pads[] = {
> ++ MX6DL_PAD_SD2_CLK__USDHC2_CLK,
> ++ MX6DL_PAD_SD2_CMD__USDHC2_CMD,
> ++ MX6DL_PAD_SD2_DAT0__USDHC2_DAT0,
> ++ MX6DL_PAD_SD2_DAT1__USDHC2_DAT1,
> ++ MX6DL_PAD_SD2_DAT2__USDHC2_DAT2,
> ++ MX6DL_PAD_SD2_DAT3__USDHC2_DAT3,
> ++};
> ++
> ++
> ++#define MX6DL_USDHC_PAD_SETTING(id, speed) \
> ++mx6dl_sd##id##_##speed##mhz[] = { \
> ++ MX6DL_PAD_SD##id##_CLK__USDHC##id##_CLK_##speed##MHZ, \
> ++ MX6DL_PAD_SD##id##_CMD__USDHC##id##_CMD_##speed##MHZ, \
> ++ MX6DL_PAD_SD##id##_DAT0__USDHC##id##_DAT0_##speed##MHZ, \
> ++ MX6DL_PAD_SD##id##_DAT1__USDHC##id##_DAT1_##speed##MHZ, \
> ++ MX6DL_PAD_SD##id##_DAT2__USDHC##id##_DAT2_##speed##MHZ, \
> ++ MX6DL_PAD_SD##id##_DAT3__USDHC##id##_DAT3_##speed##MHZ, \
> ++}
> ++
> ++/* 50,100, and 200 MHz are supported for SD3 in iomux_mx6dl.h */
> ++static iomux_v3_cfg_t MX6DL_USDHC_PAD_SETTING(3, 50);
> ++static iomux_v3_cfg_t MX6DL_USDHC_PAD_SETTING(3, 100);
> ++static iomux_v3_cfg_t MX6DL_USDHC_PAD_SETTING(3, 200);
> ++
> ++enum sd_pad_mode {
> ++ SD_PAD_MODE_LOW_SPEED,
> ++ SD_PAD_MODE_MED_SPEED,
> ++ SD_PAD_MODE_HIGH_SPEED,
> ++};
> ++
> ++static int plt_sd_pad_change(unsigned int index, int clock)
> ++{
> ++ /* LOW speed is the default state of SD pads */
> ++ static enum sd_pad_mode pad_mode = SD_PAD_MODE_LOW_SPEED;
> ++
> ++ iomux_v3_cfg_t *sd_pads_200mhz = NULL;
> ++ iomux_v3_cfg_t *sd_pads_100mhz = NULL;
> ++ iomux_v3_cfg_t *sd_pads_50mhz = NULL;
> ++
> ++ u32 sd_pads_200mhz_cnt;
> ++ u32 sd_pads_100mhz_cnt;
> ++ u32 sd_pads_50mhz_cnt;
> ++
> ++ switch (index) {
> ++ case 0:
> ++ sd_pads_50mhz = mx6dl_sd1_pads;
> ++ sd_pads_50mhz_cnt = ARRAY_SIZE(mx6dl_sd1_pads);
> ++ return mxc_iomux_v3_setup_multiple_pads(sd_pads_50mhz, sd_pads_50mhz_cnt);
> ++ break;
> ++ case 1:
> ++ sd_pads_50mhz = mx6dl_sd2_pads;
> ++ sd_pads_50mhz_cnt = ARRAY_SIZE(mx6dl_sd2_pads);
> ++ return mxc_iomux_v3_setup_multiple_pads(sd_pads_50mhz, sd_pads_50mhz_cnt);
> ++ break;
> ++ case 2:
> ++ sd_pads_200mhz = mx6dl_sd3_200mhz;
> ++ sd_pads_100mhz = mx6dl_sd3_100mhz;
> ++ sd_pads_50mhz = mx6dl_sd3_50mhz;
> ++
> ++ sd_pads_200mhz_cnt = ARRAY_SIZE(mx6dl_sd3_200mhz);
> ++ sd_pads_100mhz_cnt = ARRAY_SIZE(mx6dl_sd3_100mhz);
> ++ sd_pads_50mhz_cnt = ARRAY_SIZE(mx6dl_sd3_50mhz);
> ++ break;
> ++ default:
> ++ printk(KERN_ERR "no such SD host controller index %d\n", index);
> ++ return -EINVAL;
> ++ }
> ++
> ++ if (clock > 100000000) {
> ++ if (pad_mode == SD_PAD_MODE_HIGH_SPEED)
> ++ return 0;
> ++ BUG_ON(!sd_pads_200mhz);
> ++ pad_mode = SD_PAD_MODE_HIGH_SPEED;
> ++ return mxc_iomux_v3_setup_multiple_pads(sd_pads_200mhz,
> ++ sd_pads_200mhz_cnt);
> ++ } else if (clock > 52000000) {
> ++ if (pad_mode == SD_PAD_MODE_MED_SPEED)
> ++ return 0;
> ++ BUG_ON(!sd_pads_100mhz);
> ++ pad_mode = SD_PAD_MODE_MED_SPEED;
> ++ return mxc_iomux_v3_setup_multiple_pads(sd_pads_100mhz,
> ++ sd_pads_100mhz_cnt);
> ++ } else {
> ++ if (pad_mode == SD_PAD_MODE_LOW_SPEED)
> ++ return 0;
> ++ BUG_ON(!sd_pads_50mhz);
> ++ pad_mode = SD_PAD_MODE_LOW_SPEED;
> ++ return mxc_iomux_v3_setup_multiple_pads(sd_pads_50mhz,
> ++ sd_pads_50mhz_cnt);
> ++ }
> ++}
> ++
> ++
> ++/* ------------------------------------------------------------------------ */
> ++
> ++static const struct esdhc_platform_data wand_sd_data[3] = {
> ++ {
> ++ .cd_gpio = WAND_SD1_CD,
> ++ .wp_gpio =-EINVAL,
> ++ .keep_power_at_suspend = 1,
> ++ .support_8bit = 0,
> ++ .platform_pad_change = plt_sd_pad_change,
> ++ }, {
> ++ .cd_gpio =-EINVAL,
> ++ .wp_gpio =-EINVAL,
> ++ .keep_power_at_suspend = 1,
> ++ .platform_pad_change = plt_sd_pad_change,
> ++ }, {
> ++ .cd_gpio = WAND_SD3_CD,
> ++ .wp_gpio = WAND_SD3_WP,
> ++ .keep_power_at_suspend = 1,
> ++ .support_8bit = 0,
> ++ .delay_line = 0,
> ++ .platform_pad_change = plt_sd_pad_change,
> ++ }
> ++};
> ++
> ++/* ------------------------------------------------------------------------ */
> ++
> ++static void wand_init_sd(void) {
> ++ //int i;
> ++ /* Card Detect for SD1 & SD3, respectively */
> ++ mxc_iomux_v3_setup_pad(MX6DL_PAD_GPIO_2__GPIO_1_2);
> ++ mxc_iomux_v3_setup_pad(MX6DL_PAD_EIM_DA9__GPIO_3_9);
> ++
> ++ /* Add mmc devices in reverse order, so mmc0 always is boot sd (SD3) */
> ++/* for (i=2; i>=0; i--) {
> ++ WAND_SETUP_PADS(wand_sd_pads[i][0]);
> ++ imx6q_add_sdhci_usdhc_imx(i, &wand_sd_data[i]);
> ++ } */
> ++
> ++ /* SD3 is first, speed is set to lowest to start */
> ++ WAND_SETUP_PADS(mx6dl_sd3_50mhz);
> ++ imx6q_add_sdhci_usdhc_imx(2, &wand_sd_data[2]);
> ++
> ++ WAND_SETUP_PADS(mx6dl_sd2_pads);
> ++ imx6q_add_sdhci_usdhc_imx(1, &wand_sd_data[1]);
> ++
> ++ WAND_SETUP_PADS(mx6dl_sd1_pads);
> ++ imx6q_add_sdhci_usdhc_imx(0, &wand_sd_data[0]);
> ++}
> ++
> ++
> ++/****************************************************************************
> ++ *
> ++ * I2C
> ++ *
> ++ ****************************************************************************/
> ++
> ++static iomux_v3_cfg_t wand_i2c_pads[3][2] __initdata = {
> ++ {
> ++ MX6DL_PAD_EIM_D21__I2C1_SCL,
> ++ MX6DL_PAD_EIM_D28__I2C1_SDA,
> ++ }, {
> ++ MX6DL_PAD_KEY_COL3__I2C2_SCL,
> ++ MX6DL_PAD_KEY_ROW3__I2C2_SDA,
> ++ }, {
> ++ MX6DL_PAD_GPIO_5__I2C3_SCL,
> ++ MX6DL_PAD_GPIO_16__I2C3_SDA
> ++ }
> ++};
> ++
> ++/* ------------------------------------------------------------------------ */
> ++
> ++static struct imxi2c_platform_data wand_i2c_data[] = {
> ++ { .bitrate = 100000, },
> ++ { .bitrate = 400000, },
> ++ { .bitrate = 400000, },
> ++};
> ++
> ++/* ------------------------------------------------------------------------ */
> ++
> ++static void __init wand_init_i2c(void) {
> ++ int i;
> ++ for (i=0; i<3; i++) {
> ++ WAND_SETUP_PADS(wand_i2c_pads[i]);
> ++ imx6q_add_imx_i2c(i, &wand_i2c_data[i]);
> ++ }
> ++}
> ++
> ++
> ++/****************************************************************************
> ++ *
> ++ * Initialize debug console (UART1)
> ++ *
> ++ ****************************************************************************/
> ++
> ++static __initdata iomux_v3_cfg_t wand_uart_pads[] = {
> ++ /* UART1 (debug console) */
> ++ MX6DL_PAD_CSI0_DAT10__UART1_TXD,
> ++ MX6DL_PAD_CSI0_DAT11__UART1_RXD,
> ++ MX6DL_PAD_EIM_D19__UART1_CTS,
> ++ MX6DL_PAD_EIM_D20__UART1_RTS,
> ++};
> ++
> ++/* ------------------------------------------------------------------------ */
> ++
> ++static __init void wand_init_uart(void) {
> ++ WAND_SETUP_PADS(wand_uart_pads);
> ++
> ++ imx6q_add_imx_uart(0, NULL);
> ++}
> ++
> ++
> ++/****************************************************************************
> ++ *
> ++ * Initialize sound (SSI, ASRC, AUD3 channel and S/PDIF)
> ++ *
> ++ ****************************************************************************/
> ++
> ++static iomux_v3_cfg_t wand_audio_pads[] = {
> ++ MX6DL_PAD_CSI0_DAT4__AUDMUX_AUD3_TXC,
> ++ MX6DL_PAD_CSI0_DAT5__AUDMUX_AUD3_TXD,
> ++ MX6DL_PAD_CSI0_DAT6__AUDMUX_AUD3_TXFS,
> ++ MX6DL_PAD_CSI0_DAT7__AUDMUX_AUD3_RXD,
> ++ MX6DL_PAD_GPIO_0__CCM_CLKO,
> ++};
> ++
> ++/* ------------------------------------------------------------------------ */
> ++
> ++extern struct mxc_audio_platform_data wand_audio_channel_data;
> ++
> ++/* This function is called as a callback from the audio channel data struct */
> ++static int wand_audio_clock_enable(void) {
> ++ struct clk *clko;
> ++ struct clk *new_parent;
> ++ int rate;
> ++
> ++ clko = clk_get(NULL, "clko_clk");
> ++ if (IS_ERR(clko)) return PTR_ERR(clko);
> ++
> ++ new_parent = clk_get(NULL, "ahb");
> ++ if (!IS_ERR(new_parent)) {
> ++ clk_set_parent(clko, new_parent);
> ++ clk_put(new_parent);
> ++ }
> ++
> ++ rate = clk_round_rate(clko, 16000000);
> ++ if (rate < 8000000 || rate > 27000000) {
> ++ pr_err("SGTL5000: mclk freq %d out of range!\n", rate);
> ++ clk_put(clko);
> ++ return -1;
> ++ }
> ++
> ++ wand_audio_channel_data.sysclk = rate;
> ++ clk_set_rate(clko, rate);
> ++ clk_enable(clko);
> ++
> ++ return 0;
> ++}
> ++
> ++/* ------------------------------------------------------------------------ */
> ++
> ++/* This struct is added by the baseboard when initializing the codec */
> ++struct mxc_audio_platform_data wand_audio_channel_data = {
> ++ .ssi_num = 1,
> ++ .src_port = 2,
> ++ .ext_port = 3, /* audio channel: 3=AUD3. TODO: EDM */
> ++ .init = wand_audio_clock_enable,
> ++ .hp_gpio = -1,
> ++};
> ++EXPORT_SYMBOL_GPL(wand_audio_channel_data); /* TODO: edm naming? */
> ++
> ++/* ------------------------------------------------------------------------ */
> ++
> ++static int wand_set_spdif_clk_rate(struct clk *clk, unsigned long rate) {
> ++ unsigned long rate_actual;
> ++ rate_actual = clk_round_rate(clk, rate);
> ++ clk_set_rate(clk, rate_actual);
> ++ return 0;
> ++}
> ++
> ++/* ------------------------------------------------------------------------ */
> ++
> ++static struct mxc_spdif_platform_data wand_spdif = {
> ++ .spdif_tx = 1, /* enable tx */
> ++ .spdif_rx = 1, /* enable rx */
> ++ .spdif_clk_44100 = 1, /* tx clk from spdif0_clk_root */
> ++ .spdif_clk_48000 = 1, /* tx clk from spdif0_clk_root */
> ++ .spdif_div_44100 = 23,
> ++ .spdif_div_48000 = 37,
> ++ .spdif_div_32000 = 37,
> ++ .spdif_rx_clk = 0, /* rx clk from spdif stream */
> ++ .spdif_clk_set_rate = wand_set_spdif_clk_rate,
> ++ .spdif_clk = NULL, /* spdif bus clk */
> ++};
> ++
> ++/* ------------------------------------------------------------------------ */
> ++
> ++static struct imx_ssi_platform_data wand_ssi_pdata = {
> ++ .flags = IMX_SSI_DMA | IMX_SSI_SYN,
> ++};
> ++
> ++/* ------------------------------------------------------------------------ */
> ++
> ++static struct imx_asrc_platform_data wand_asrc_data = {
> ++ .channel_bits = 4,
> ++ .clk_map_ver = 2,
> ++};
> ++
> ++/* ------------------------------------------------------------------------ */
> ++
> ++void __init wand_init_audio(void) {
> ++ WAND_SETUP_PADS(wand_audio_pads);
> ++
> ++ /* Sample rate converter is added together with audio */
> ++ wand_asrc_data.asrc_core_clk = clk_get(NULL, "asrc_clk");
> ++ wand_asrc_data.asrc_audio_clk = clk_get(NULL, "asrc_serial_clk");
> ++ imx6q_add_asrc(&wand_asrc_data);
> ++
> ++ imx6q_add_imx_ssi(1, &wand_ssi_pdata);
> ++ /* Enable SPDIF */
> ++
> ++ mxc_iomux_v3_setup_pad(MX6DL_PAD_ENET_RXD0__SPDIF_OUT1);
> ++
> ++ wand_spdif.spdif_core_clk = clk_get_sys("mxc_spdif.0", NULL);
> ++ clk_put(wand_spdif.spdif_core_clk);
> ++ imx6q_add_spdif(&wand_spdif);
> ++ imx6q_add_spdif_dai();
> ++ imx6q_add_spdif_audio_device();
> ++}
> ++
> ++
> ++/*****************************************************************************
> ++ *
> ++ * Init FEC and AR8031 PHY
> ++ *
> ++ *****************************************************************************/
> ++
> ++static iomux_v3_cfg_t wand_fec_pads[] = {
> ++ MX6DL_PAD_ENET_MDIO__ENET_MDIO,
> ++ MX6DL_PAD_ENET_MDC__ENET_MDC,
> ++ MX6DL_PAD_ENET_REF_CLK__ENET_TX_CLK,
> ++ MX6DL_PAD_RGMII_TXC__ENET_RGMII_TXC,
> ++ MX6DL_PAD_RGMII_TD0__ENET_RGMII_TD0,
> ++ MX6DL_PAD_RGMII_TD1__ENET_RGMII_TD1,
> ++ MX6DL_PAD_RGMII_TD2__ENET_RGMII_TD2,
> ++ MX6DL_PAD_RGMII_TD3__ENET_RGMII_TD3,
> ++ MX6DL_PAD_RGMII_TX_CTL__ENET_RGMII_TX_CTL,
> ++ MX6DL_PAD_RGMII_RXC__ENET_RGMII_RXC,
> ++ MX6DL_PAD_RGMII_RD0__ENET_RGMII_RD0,
> ++ MX6DL_PAD_RGMII_RD1__ENET_RGMII_RD1,
> ++ MX6DL_PAD_RGMII_RD2__ENET_RGMII_RD2,
> ++ MX6DL_PAD_RGMII_RD3__ENET_RGMII_RD3,
> ++ MX6DL_PAD_RGMII_RX_CTL__ENET_RGMII_RX_CTL,
> ++ MX6DL_PAD_ENET_TX_EN__GPIO_1_28,
> ++ MX6DL_PAD_EIM_D29__GPIO_3_29,
> ++};
> ++
> ++/* ------------------------------------------------------------------------ */
> ++
> ++static int wand_fec_phy_init(struct phy_device *phydev) {
> ++ unsigned short val;
> ++
> ++ /* Enable AR8031 125MHz clk */
> ++ phy_write(phydev, 0x0d, 0x0007); /* Set device address to 7*/
> ++ phy_write(phydev, 0x00, 0x8000); /* Apply by soft reset */
> ++ udelay(500);
> ++
> ++ phy_write(phydev, 0x0e, 0x8016); /* set mmd reg */
> ++ phy_write(phydev, 0x0d, 0x4007); /* apply */
> ++
> ++ val = phy_read(phydev, 0xe);
> ++ val &= 0xffe3;
> ++ val |= 0x18;
> ++ phy_write(phydev, 0xe, val);
> ++ phy_write(phydev, 0x0d, 0x4007); /* Post data */
> ++
> ++ /* Introduce random tx clock delay. Why is this needed? */
> ++ phy_write(phydev, 0x1d, 0x5);
> ++ val = phy_read(phydev, 0x1e);
> ++ val |= 0x0100;
> ++ phy_write(phydev, 0x1e, val);
> ++
> ++ return 0;
> ++}
> ++
> ++/* ------------------------------------------------------------------------ */
> ++
> ++static int wand_fec_power_hibernate(struct phy_device *phydev) { return 0; }
> ++
> ++/* ------------------------------------------------------------------------ */
> ++
> ++static struct fec_platform_data wand_fec_data __initdata = {
> ++ .init = wand_fec_phy_init,
> ++ .power_hibernate = wand_fec_power_hibernate,
> ++ .phy = PHY_INTERFACE_MODE_RGMII,
> ++};
> ++
> ++/* ------------------------------------------------------------------------ */
> ++
> ++static __init void wand_init_ethernet(void) {
> ++ WAND_SETUP_PADS(wand_fec_pads);
> ++
> ++ gpio_request(WAND_RGMII_RST, "rgmii reset");
> ++ gpio_direction_output(WAND_RGMII_RST, 0);
> ++#ifdef CONFIG_FEC_1588
> ++ mxc_iomux_set_gpr_register(1, 21, 1, 1);
> ++#endif
> ++ msleep(10);
> ++ gpio_set_value(WAND_RGMII_RST, 1);
> ++ imx6_init_fec(wand_fec_data);
> ++}
> ++
> ++
> ++/****************************************************************************
> ++ *
> ++ * USB
> ++ *
> ++ ****************************************************************************/
> ++
> ++static __initdata iomux_v3_cfg_t wand_usb_pads[] = {
> ++ MX6DL_PAD_GPIO_9__GPIO_1_9,
> ++ MX6DL_PAD_GPIO_1__USBOTG_ID,
> ++ MX6DL_PAD_EIM_D22__GPIO_3_22,
> ++ MX6DL_PAD_EIM_D30__GPIO_3_30
> ++};
> ++
> ++/* ------------------------------------------------------------------------ */
> ++
> ++static void wand_usbotg_vbus(bool on) {
> ++ gpio_set_value_cansleep(WAND_USB_OTG_PWR, !on);
> ++}
> ++
> ++/* ------------------------------------------------------------------------ */
> ++
> ++static __init void wand_init_usb(void) {
> ++ WAND_SETUP_PADS(wand_usb_pads);
> ++
> ++ gpio_request(WAND_USB_OTG_OC, "otg oc");
> ++ gpio_direction_input(WAND_USB_OTG_OC);
> ++
> ++ gpio_request(WAND_USB_OTG_PWR, "otg pwr");
> ++ gpio_direction_output(WAND_USB_OTG_PWR, 0);
> ++
> ++ imx_otg_base = MX6_IO_ADDRESS(MX6Q_USB_OTG_BASE_ADDR);
> ++ mxc_iomux_set_gpr_register(1, 13, 1, 1);
> ++
> ++ mx6_set_otghost_vbus_func(wand_usbotg_vbus);
> ++
> ++ gpio_request(WAND_USB_H1_OC, "usbh1 oc");
> ++ gpio_direction_input(WAND_USB_H1_OC);
> ++}
> ++
> ++
> ++/****************************************************************************
> ++ *
> ++ * IPU
> ++ *
> ++ ****************************************************************************/
> ++
> ++static struct imx_ipuv3_platform_data wand_ipu_data[] = {
> ++ {
> ++ .rev = 4,
> ++ .csi_clk[0] = "ccm_clk0",
> ++ }, {
> ++ .rev = 4,
> ++ .csi_clk[0] = "ccm_clk0",
> ++ },
> ++};
> ++
> ++/* ------------------------------------------------------------------------ */
> ++
> ++static __init void wand_init_ipu(void) {
> ++ imx6q_add_ipuv3(0, &wand_ipu_data[0]);
> ++}
> ++
> ++
> ++/****************************************************************************
> ++ *
> ++ * HDMI
> ++ *
> ++ ****************************************************************************/
> ++
> ++static struct ipuv3_fb_platform_data wand_hdmi_fb[] = {
> ++ { /* hdmi framebuffer */
> ++ .disp_dev = "hdmi",
> ++ .interface_pix_fmt = IPU_PIX_FMT_RGB32,
> ++ .mode_str = "1920x1080 at 60",
> ++ .default_bpp = 32,
> ++ .int_clk = false,
> ++ }
> ++};
> ++
> ++/* ------------------------------------------------------------------------ */
> ++
> ++static void wand_hdmi_init(int ipu_id, int disp_id) {
> ++ if ((unsigned)ipu_id > 1) ipu_id = 0;
> ++ if ((unsigned)disp_id > 1) disp_id = 0;
> ++
> ++ mxc_iomux_set_gpr_register(3, 2, 2, 2*ipu_id + disp_id);
> ++}
> ++
> ++/* ------------------------------------------------------------------------ */
> ++
> ++static struct fsl_mxc_hdmi_platform_data wand_hdmi_data = {
> ++ .init = wand_hdmi_init,
> ++};
> ++
> ++/* ------------------------------------------------------------------------ */
> ++
> ++static struct fsl_mxc_hdmi_core_platform_data wand_hdmi_core_data = {
> ++ .ipu_id = 0,
> ++ .disp_id = 1,
> ++};
> ++
> ++/* ------------------------------------------------------------------------ */
> ++
> ++static const struct i2c_board_info wand_hdmi_i2c_info = {
> ++ I2C_BOARD_INFO("mxc_hdmi_i2c", 0x50),
> ++};
> ++
> ++/* ------------------------------------------------------------------------ */
> ++
> ++static void wand_init_hdmi(void) {
> ++ i2c_register_board_info(0, &wand_hdmi_i2c_info, 1);
> ++ imx6q_add_mxc_hdmi_core(&wand_hdmi_core_data);
> ++ imx6q_add_mxc_hdmi(&wand_hdmi_data);
> ++ imx6q_add_ipuv3fb(0, wand_hdmi_fb);
> ++
> ++ /* Enable HDMI audio */
> ++ imx6q_add_hdmi_soc();
> ++ imx6q_add_hdmi_soc_dai();
> ++ mxc_iomux_set_gpr_register(0, 0, 1, 1);
> ++}
> ++
> ++
> ++/****************************************************************************
> ++ *
> ++ * WiFi
> ++ *
> ++ ****************************************************************************/
> ++
> ++static __initdata iomux_v3_cfg_t wand_wifi_pads[] = {
> ++ /* ref_on, enable 32k clock */
> ++ MX6DL_PAD_EIM_EB1__GPIO_2_29,
> ++ /* Wifi reset (resets when low!) */
> ++ MX6DL_PAD_EIM_A25__GPIO_5_2,
> ++ /* reg on, signal to FDC6331L */
> ++ MX6DL_PAD_ENET_RXD1__GPIO_1_26,
> ++ /* host wake */
> ++ MX6DL_PAD_ENET_TXD1__GPIO_1_29,
> ++ /* wl wake - nc */
> ++ MX6DL_PAD_ENET_TXD0__GPIO_1_30,
> ++};
> ++
> ++/* ------------------------------------------------------------------------ */
> ++
> ++/* assumes SD/MMC pins are set; call after wand_init_sd() */
> ++static __init void wand_init_wifi(void) {
> ++ WAND_SETUP_PADS(wand_wifi_pads);
> ++
> ++ gpio_request(WAND_WL_RST_N, "wl_rst_n");
> ++ gpio_direction_output(WAND_WL_RST_N, 0);
> ++ msleep(11);
> ++ gpio_set_value(WAND_WL_RST_N, 1);
> ++
> ++ gpio_request(WAND_WL_REF_ON, "wl_ref_on");
> ++ gpio_direction_output(WAND_WL_REF_ON, 1);
> ++
> ++ gpio_request(WAND_WL_REG_ON, "wl_reg_on");
> ++ gpio_direction_output(WAND_WL_REG_ON, 1);
> ++
> ++ gpio_request(WAND_WL_WAKE, "wl_wake");
> ++ gpio_direction_output(WAND_WL_WAKE, 1);
> ++
> ++ gpio_request(WAND_WL_HOST_WAKE, "wl_host_wake");
> ++ gpio_direction_input(WAND_WL_HOST_WAKE);
> ++}
> ++
> ++
> ++/****************************************************************************
> ++ *
> ++ * Bluetooth
> ++ *
> ++ ****************************************************************************/
> ++
> ++static __initdata iomux_v3_cfg_t wand_bt_pads[] = {
> ++ /* BT_ON, BT_WAKE and BT_HOST_WAKE */
> ++ MX6DL_PAD_EIM_DA13__GPIO_3_13,
> ++ MX6DL_PAD_EIM_DA14__GPIO_3_14,
> ++ MX6DL_PAD_EIM_DA15__GPIO_3_15,
> ++
> ++ /* AUD5 channel goes to BT */
> ++ MX6DL_PAD_KEY_COL0__AUDMUX_AUD5_TXC,
> ++ MX6DL_PAD_KEY_ROW0__AUDMUX_AUD5_TXD,
> ++ MX6DL_PAD_KEY_COL1__AUDMUX_AUD5_TXFS,
> ++ MX6DL_PAD_KEY_ROW1__AUDMUX_AUD5_RXD,
> ++
> ++ /* Bluetooth is on UART3*/
> ++ MX6DL_PAD_EIM_D23__UART3_CTS,
> ++ MX6DL_PAD_EIM_D24__UART3_TXD,
> ++ MX6DL_PAD_EIM_D25__UART3_RXD,
> ++ MX6DL_PAD_EIM_EB3__UART3_RTS,
> ++};
> ++
> ++/* ------------------------------------------------------------------------ */
> ++
> ++static const struct imxuart_platform_data wand_bt_uart_data = {
> ++ .flags = IMXUART_HAVE_RTSCTS | IMXUART_SDMA,
> ++ .dma_req_tx = MX6Q_DMA_REQ_UART3_TX,
> ++ .dma_req_rx = MX6Q_DMA_REQ_UART3_RX,
> ++};
> ++
> ++/* ------------------------------------------------------------------------ */
> ++
> ++/* This assumes wifi is initialized (chip has power) */
> ++static __init void wand_init_bluetooth(void) {
> ++ WAND_SETUP_PADS(wand_bt_pads);
> ++
> ++ imx6q_add_imx_uart(2, &wand_bt_uart_data);
> ++
> ++ gpio_request(WAND_BT_ON, "bt_on");
> ++ gpio_direction_output(WAND_BT_ON, 0);
> ++ msleep(11);
> ++ gpio_set_value(WAND_BT_ON, 1);
> ++
> ++ gpio_request(WAND_BT_WAKE, "bt_wake");
> ++ gpio_direction_output(WAND_BT_WAKE, 1);
> ++
> ++ gpio_request(WAND_BT_HOST_WAKE, "bt_host_wake");
> ++ gpio_direction_input(WAND_BT_WAKE);
> ++}
> ++
> ++
> ++/****************************************************************************
> ++ *
> ++ * Power and thermal management
> ++ *
> ++ ****************************************************************************/
> ++
> ++extern bool enable_wait_mode;
> ++
> ++static const struct anatop_thermal_platform_data wand_thermal = {
> ++ .name = "anatop_thermal",
> ++};
> ++
> ++/* ------------------------------------------------------------------------ */
> ++
> ++static void wand_suspend_enter(void) {
> ++ gpio_set_value(WAND_WL_WAKE, 0);
> ++ gpio_set_value(WAND_BT_WAKE, 0);
> ++}
> ++
> ++/* ------------------------------------------------------------------------ */
> ++
> ++static void wand_suspend_exit(void) {
> ++ gpio_set_value(WAND_WL_WAKE, 1);
> ++ gpio_set_value(WAND_BT_WAKE, 1);
> ++}
> ++
> ++/* ------------------------------------------------------------------------ */
> ++
> ++static const struct pm_platform_data wand_pm_data = {
> ++ .name = "imx_pm",
> ++ .suspend_enter = wand_suspend_enter,
> ++ .suspend_exit = wand_suspend_exit,
> ++};
> ++
> ++/* ------------------------------------------------------------------------ */
> ++
> ++static const struct mxc_dvfs_platform_data wand_dvfscore_data = {
> ++ .reg_id = "cpu_vddgp",
> ++ .clk1_id = "cpu_clk",
> ++ .clk2_id = "gpc_dvfs_clk",
> ++ .gpc_cntr_offset = MXC_GPC_CNTR_OFFSET,
> ++ .ccm_cdcr_offset = MXC_CCM_CDCR_OFFSET,
> ++ .ccm_cacrr_offset = MXC_CCM_CACRR_OFFSET,
> ++ .ccm_cdhipr_offset = MXC_CCM_CDHIPR_OFFSET,
> ++ .prediv_mask = 0x1F800,
> ++ .prediv_offset = 11,
> ++ .prediv_val = 3,
> ++ .div3ck_mask = 0xE0000000,
> ++ .div3ck_offset = 29,
> ++ .div3ck_val = 2,
> ++ .emac_val = 0x08,
> ++ .upthr_val = 25,
> ++ .dnthr_val = 9,
> ++ .pncthr_val = 33,
> ++ .upcnt_val = 10,
> ++ .dncnt_val = 10,
> ++ .delay_time = 80,
> ++};
> ++
> ++/* ------------------------------------------------------------------------ */
> ++
> ++static __init void wand_init_pm(void) {
> ++ enable_wait_mode = false;
> ++ imx6q_add_anatop_thermal_imx(1, &wand_thermal);
> ++ imx6q_add_pm_imx(0, &wand_pm_data);
> ++ imx6q_add_dvfs_core(&wand_dvfscore_data);
> ++ imx6q_add_busfreq();
> ++}
> ++
> ++
> ++/****************************************************************************
> ++ *
> ++ * Expansion pin header GPIOs
> ++ *
> ++ ****************************************************************************/
> ++
> ++static __initdata iomux_v3_cfg_t wand_external_gpio_pads[] = {
> ++ MX6DL_PAD_EIM_DA11__GPIO_3_11,
> ++ MX6DL_PAD_EIM_D27__GPIO_3_27,
> ++ MX6DL_PAD_EIM_BCLK__GPIO_6_31,
> ++ MX6DL_PAD_ENET_RX_ER__GPIO_1_24,
> ++ MX6DL_PAD_SD3_RST__GPIO_7_8,
> ++ MX6DL_PAD_EIM_D26__GPIO_3_26,
> ++ MX6DL_PAD_EIM_DA8__GPIO_3_8,
> ++ MX6DL_PAD_GPIO_19__GPIO_4_5,
> ++};
> ++
> ++/* ------------------------------------------------------------------------ */
> ++
> ++static __init void wand_init_external_gpios(void) {
> ++ WAND_SETUP_PADS(wand_external_gpio_pads);
> ++
> ++ gpio_request(IMX_GPIO_NR(3, 11), "external_gpio_0");
> ++ gpio_export(IMX_GPIO_NR(3, 11), true);
> ++ gpio_request(IMX_GPIO_NR(3, 27), "external_gpio_1");
> ++ gpio_export(IMX_GPIO_NR(3, 27), true);
> ++ gpio_request(IMX_GPIO_NR(6, 31), "external_gpio_2");
> ++ gpio_export(IMX_GPIO_NR(6, 31), true);
> ++ gpio_request(IMX_GPIO_NR(1, 24), "external_gpio_3");
> ++ gpio_export(IMX_GPIO_NR(1, 24), true);
> ++ gpio_request(IMX_GPIO_NR(7, 8), "external_gpio_4");
> ++ gpio_export(IMX_GPIO_NR(7, 8), true);
> ++ gpio_request(IMX_GPIO_NR(3, 26), "external_gpio_5");
> ++ gpio_export(IMX_GPIO_NR(3, 26), true);
> ++ gpio_request(IMX_GPIO_NR(3, 8), "external_gpio_6");
> ++ gpio_export(IMX_GPIO_NR(3, 8), true);
> ++ gpio_request(IMX_GPIO_NR(4, 5), "external_gpio_7");
> ++ gpio_export(IMX_GPIO_NR(4, 5), true);
> ++}
> ++
> ++
> ++/****************************************************************************
> ++ *
> ++ * SPI - while not used on the Wandboard, the pins are routed out
> ++ *
> ++ ****************************************************************************/
> ++
> ++static __initdata iomux_v3_cfg_t wand_spi_pads[] = {
> ++ MX6DL_PAD_EIM_D16__ECSPI1_SCLK,
> ++ MX6DL_PAD_EIM_D17__ECSPI1_MISO,
> ++ MX6DL_PAD_EIM_D18__ECSPI1_MOSI,
> ++ MX6DL_PAD_EIM_EB2__GPIO_2_30,
> ++
> ++ MX6DL_PAD_EIM_CS0__ECSPI2_SCLK,
> ++ MX6DL_PAD_EIM_CS1__ECSPI2_MOSI,
> ++ MX6DL_PAD_EIM_OE__ECSPI2_MISO,
> ++ MX6DL_PAD_EIM_RW__GPIO_2_26,
> ++ MX6DL_PAD_EIM_LBA__GPIO_2_27,
> ++};
> ++/* The choice of using gpios for chipselect is deliberate,
> ++ there can be issues using the dedicated mux modes for cs.
> ++*/
> ++
> ++/* ------------------------------------------------------------------------ */
> ++
> ++static const int wand_spi1_chipselect[] = { IMX_GPIO_NR(2, 30) };
> ++
> ++/* platform device */
> ++static const struct spi_imx_master wand_spi1_data = {
> ++ .chipselect = wand_spi1_chipselect,
> ++ .num_chipselect = ARRAY_SIZE(wand_spi1_chipselect),
> ++};
> ++
> ++/* ------------------------------------------------------------------------ */
> ++
> ++static const int wand_spi2_chipselect[] = { IMX_GPIO_NR(2, 26), IMX_GPIO_NR(2, 27) };
> ++
> ++static const struct spi_imx_master wand_spi2_data = {
> ++ .chipselect = wand_spi2_chipselect,
> ++ .num_chipselect = ARRAY_SIZE(wand_spi2_chipselect),
> ++};
> ++
> ++/* ------------------------------------------------------------------------ */
> ++
> ++static void __init wand_init_spi(void) {
> ++ WAND_SETUP_PADS(wand_spi_pads);
> ++
> ++ imx6q_add_ecspi(0, &wand_spi1_data);
> ++ imx6q_add_ecspi(1, &wand_spi2_data);
> ++}
> ++
> ++
> ++/****************************************************************************
> ++ *
> ++ * Vivante GPU/VPU
> ++ *
> ++ ****************************************************************************/
> ++
> ++static const __initconst struct imx_viv_gpu_data wand_gpu_data = {
> ++ .phys_baseaddr = 0,
> ++ .iobase_3d = GPU_3D_ARB_BASE_ADDR,
> ++ .irq_3d = MXC_INT_GPU3D_IRQ,
> ++ .iobase_2d = GPU_2D_ARB_BASE_ADDR,
> ++ .irq_2d = MXC_INT_GPU2D_IRQ,
> ++ .iobase_vg = OPENVG_ARB_BASE_ADDR,
> ++ .irq_vg = MXC_INT_OPENVG_XAQ2,
> ++};
> ++
> ++static struct viv_gpu_platform_data wand_gpu_pdata = {
> ++ .reserved_mem_size = SZ_128M + SZ_64M - SZ_16M,
> ++};
> ++
> ++static __init void wand_init_gpu(void) {
> ++ imx_add_viv_gpu(&wand_gpu_data, &wand_gpu_pdata);
> ++ imx6q_add_vpu();
> ++ imx6q_add_v4l2_output(0);
> ++}
> ++
> ++/*****************************************************************************
> ++ *
> ++ * Init clocks and early boot console
> ++ *
> ++ *****************************************************************************/
> ++
> ++extern void __iomem *twd_base;
> ++
> ++static void __init wand_init_timer(void) {
> ++ struct clk *uart_clk;
> ++#ifdef CONFIG_LOCAL_TIMERS
> ++ twd_base = ioremap(LOCAL_TWD_ADDR, SZ_256);
> ++#endif
> ++ mx6_clocks_init(32768, 24000000, 0, 0);
> ++
> ++ uart_clk = clk_get_sys("imx-uart.0", NULL);
> ++ early_console_setup(UART1_BASE_ADDR, uart_clk);
> ++}
> ++
> ++/* ------------------------------------------------------------------------ */
> ++
> ++static struct sys_timer wand_timer = {
> ++ .init = wand_init_timer,
> ++};
> ++
> ++/* ------------------------------------------------------------------------ */
> ++
> ++static void __init wand_reserve(void) {
> ++ phys_addr_t phys;
> ++
> ++ if (wand_gpu_pdata.reserved_mem_size) {
> ++ phys = memblock_alloc_base(wand_gpu_pdata.reserved_mem_size, SZ_4K, SZ_512M);
> ++ memblock_remove(phys, wand_gpu_pdata.reserved_mem_size);
> ++ wand_gpu_pdata.reserved_mem_base = phys;
> ++ }
> ++}
> ++
> ++/*****************************************************************************
> ++ *
> ++ * BOARD INIT
> ++ *
> ++ *****************************************************************************/
> ++
> ++static void __init wand_board_init(void) {
> ++ wand_init_dma();
> ++ wand_init_uart();
> ++ wand_init_sd();
> ++ wand_init_i2c();
> ++ wand_init_audio();
> ++ wand_init_ethernet();
> ++ wand_init_usb();
> ++ wand_init_ipu();
> ++ imx6q_add_imx_snvs_rtc();
> ++ wand_init_hdmi();
> ++ wand_init_wifi();
> ++ wand_init_bluetooth();
> ++ wand_init_pm();
> ++ wand_init_external_gpios();
> ++ wand_init_spi();
> ++ wand_init_gpu();
> ++}
> ++
> ++/* ------------------------------------------------------------------------ */
> ++
> ++MACHINE_START(WANDBOARD, "Wandboard")
> ++ .boot_params = MX6_PHYS_OFFSET + 0x100,
> ++ .map_io = mx6_map_io,
> ++ .init_irq = mx6_init_irq,
> ++ .init_machine = wand_board_init,
> ++ .timer = &wand_timer,
> ++ .reserve = wand_reserve,
> ++MACHINE_END
> ++
> +diff --git a/arch/arm/tools/mach-types b/arch/arm/tools/mach-types
> +index 88210d9..5b4c1be 100644
> +--- a/arch/arm/tools/mach-types
> ++++ b/arch/arm/tools/mach-types
> +@@ -1119,4 +1119,5 @@ mx6q_sabresd MACH_MX6Q_SABRESD MX6Q_SABRESD 3980
> + mx6q_arm2 MACH_MX6Q_ARM2 MX6Q_ARM2 3837
> + mx6sl_arm2 MACH_MX6SL_ARM2 MX6SL_ARM2 4091
> + mx6sl_evk MACH_MX6SL_EVK MX6SL_EVK 4307
> ++wandboard MACH_WANDBOARD WANDBOARD 4412
> +
> +--
> +1.7.9.5
> +
> diff --git a/recipes-kernel/linux/linux-imx-3.0.35/wandboard-dual/defconfig b/recipes-kernel/linux/linux-imx-3.0.35/wandboard-dual/defconfig
> new file mode 100644
> index 0000000..cbc3c34
> --- /dev/null
> +++ b/recipes-kernel/linux/linux-imx-3.0.35/wandboard-dual/defconfig
> @@ -0,0 +1,2762 @@
> +#
> +# Automatically generated make config: don't edit
> +# Linux/arm 3.0.35 Kernel Configuration
> +#
> +CONFIG_ARM=y
> +CONFIG_HAVE_PWM=y
> +CONFIG_SYS_SUPPORTS_APM_EMULATION=y
> +CONFIG_HAVE_SCHED_CLOCK=y
> +CONFIG_GENERIC_GPIO=y
> +# CONFIG_ARCH_USES_GETTIMEOFFSET is not set
> +CONFIG_GENERIC_CLOCKEVENTS=y
> +CONFIG_GENERIC_CLOCKEVENTS_BROADCAST=y
> +CONFIG_KTIME_SCALAR=y
> +CONFIG_HAVE_PROC_CPU=y
> +CONFIG_STACKTRACE_SUPPORT=y
> +CONFIG_LOCKDEP_SUPPORT=y
> +CONFIG_TRACE_IRQFLAGS_SUPPORT=y
> +CONFIG_HARDIRQS_SW_RESEND=y
> +CONFIG_GENERIC_IRQ_PROBE=y
> +CONFIG_GENERIC_LOCKBREAK=y
> +CONFIG_RWSEM_GENERIC_SPINLOCK=y
> +CONFIG_ARCH_HAS_CPUFREQ=y
> +CONFIG_ARCH_HAS_CPU_IDLE_WAIT=y
> +CONFIG_GENERIC_HWEIGHT=y
> +CONFIG_GENERIC_CALIBRATE_DELAY=y
> +CONFIG_ZONE_DMA=y
> +CONFIG_NEED_DMA_MAP_STATE=y
> +CONFIG_FIQ=y
> +CONFIG_VECTORS_BASE=0xffff0000
> +# CONFIG_ARM_PATCH_PHYS_VIRT is not set
> +CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
> +CONFIG_HAVE_IRQ_WORK=y
> +CONFIG_IRQ_WORK=y
> +
> +#
> +# General setup
> +#
> +CONFIG_EXPERIMENTAL=y
> +CONFIG_INIT_ENV_ARG_LIMIT=32
> +CONFIG_CROSS_COMPILE=""
> +CONFIG_LOCALVERSION="-1.1.0+yocto"
> +CONFIG_LOCALVERSION_AUTO=y
> +CONFIG_HAVE_KERNEL_GZIP=y
> +CONFIG_HAVE_KERNEL_LZMA=y
> +CONFIG_HAVE_KERNEL_LZO=y
> +CONFIG_KERNEL_GZIP=y
> +# CONFIG_KERNEL_LZMA is not set
> +# CONFIG_KERNEL_LZO is not set
> +CONFIG_DEFAULT_HOSTNAME="(none)"
> +CONFIG_SWAP=y
> +CONFIG_SYSVIPC=y
> +CONFIG_SYSVIPC_SYSCTL=y
> +# CONFIG_POSIX_MQUEUE is not set
> +# CONFIG_BSD_PROCESS_ACCT is not set
> +# CONFIG_FHANDLE is not set
> +# CONFIG_TASKSTATS is not set
> +# CONFIG_AUDIT is not set
> +CONFIG_HAVE_GENERIC_HARDIRQS=y
> +
> +#
> +# IRQ subsystem
> +#
> +CONFIG_GENERIC_HARDIRQS=y
> +CONFIG_HAVE_SPARSE_IRQ=y
> +CONFIG_GENERIC_IRQ_SHOW=y
> +# CONFIG_SPARSE_IRQ is not set
> +
> +#
> +# RCU Subsystem
> +#
> +CONFIG_TREE_PREEMPT_RCU=y
> +CONFIG_PREEMPT_RCU=y
> +# CONFIG_RCU_TRACE is not set
> +CONFIG_RCU_FANOUT=32
> +# CONFIG_RCU_FANOUT_EXACT is not set
> +# CONFIG_TREE_RCU_TRACE is not set
> +# CONFIG_RCU_BOOST is not set
> +CONFIG_IKCONFIG=y
> +CONFIG_IKCONFIG_PROC=y
> +CONFIG_LOG_BUF_SHIFT=14
> +CONFIG_CGROUPS=y
> +# CONFIG_CGROUP_DEBUG is not set
> +# CONFIG_CGROUP_FREEZER is not set
> +# CONFIG_CGROUP_DEVICE is not set
> +# CONFIG_CPUSETS is not set
> +# CONFIG_CGROUP_CPUACCT is not set
> +# CONFIG_RESOURCE_COUNTERS is not set
> +# CONFIG_CGROUP_PERF is not set
> +# CONFIG_CGROUP_SCHED is not set
> +# CONFIG_BLK_CGROUP is not set
> +# CONFIG_NAMESPACES is not set
> +# CONFIG_SCHED_AUTOGROUP is not set
> +# CONFIG_SYSFS_DEPRECATED is not set
> +# CONFIG_RELAY is not set
> +# CONFIG_BLK_DEV_INITRD is not set
> +# CONFIG_CC_OPTIMIZE_FOR_SIZE is not set
> +CONFIG_SYSCTL=y
> +CONFIG_ANON_INODES=y
> +CONFIG_EXPERT=y
> +CONFIG_UID16=y
> +CONFIG_SYSCTL_SYSCALL=y
> +CONFIG_KALLSYMS=y
> +CONFIG_HOTPLUG=y
> +CONFIG_PRINTK=y
> +CONFIG_BUG=y
> +CONFIG_ELF_CORE=y
> +CONFIG_BASE_FULL=y
> +CONFIG_FUTEX=y
> +CONFIG_EPOLL=y
> +CONFIG_SIGNALFD=y
> +CONFIG_TIMERFD=y
> +CONFIG_EVENTFD=y
> +CONFIG_SHMEM=y
> +CONFIG_AIO=y
> +CONFIG_EMBEDDED=y
> +CONFIG_HAVE_PERF_EVENTS=y
> +CONFIG_PERF_USE_VMALLOC=y
> +
> +#
> +# Kernel Performance Events And Counters
> +#
> +CONFIG_PERF_EVENTS=y
> +# CONFIG_PERF_COUNTERS is not set
> +CONFIG_VM_EVENT_COUNTERS=y
> +CONFIG_SLUB_DEBUG=y
> +CONFIG_COMPAT_BRK=y
> +# CONFIG_SLAB is not set
> +CONFIG_SLUB=y
> +# CONFIG_SLOB is not set
> +# CONFIG_PROFILING is not set
> +CONFIG_HAVE_OPROFILE=y
> +# CONFIG_KPROBES is not set
> +CONFIG_HAVE_KPROBES=y
> +CONFIG_HAVE_KRETPROBES=y
> +CONFIG_USE_GENERIC_SMP_HELPERS=y
> +CONFIG_HAVE_REGS_AND_STACK_ACCESS_API=y
> +CONFIG_HAVE_CLK=y
> +CONFIG_HAVE_DMA_API_DEBUG=y
> +CONFIG_HAVE_HW_BREAKPOINT=y
> +
> +#
> +# GCOV-based kernel profiling
> +#
> +# CONFIG_GCOV_KERNEL is not set
> +CONFIG_HAVE_GENERIC_DMA_COHERENT=y
> +CONFIG_SLABINFO=y
> +CONFIG_RT_MUTEXES=y
> +CONFIG_BASE_SMALL=0
> +CONFIG_MODULES=y
> +# CONFIG_MODULE_FORCE_LOAD is not set
> +CONFIG_MODULE_UNLOAD=y
> +CONFIG_MODULE_FORCE_UNLOAD=y
> +CONFIG_MODVERSIONS=y
> +# CONFIG_MODULE_SRCVERSION_ALL is not set
> +CONFIG_STOP_MACHINE=y
> +CONFIG_BLOCK=y
> +CONFIG_LBDAF=y
> +# CONFIG_BLK_DEV_BSG is not set
> +# CONFIG_BLK_DEV_INTEGRITY is not set
> +
> +#
> +# IO Schedulers
> +#
> +CONFIG_IOSCHED_NOOP=y
> +CONFIG_IOSCHED_DEADLINE=y
> +CONFIG_IOSCHED_CFQ=y
> +# CONFIG_DEFAULT_DEADLINE is not set
> +CONFIG_DEFAULT_CFQ=y
> +# CONFIG_DEFAULT_NOOP is not set
> +CONFIG_DEFAULT_IOSCHED="cfq"
> +# CONFIG_INLINE_SPIN_TRYLOCK is not set
> +# CONFIG_INLINE_SPIN_TRYLOCK_BH is not set
> +# CONFIG_INLINE_SPIN_LOCK is not set
> +# CONFIG_INLINE_SPIN_LOCK_BH is not set
> +# CONFIG_INLINE_SPIN_LOCK_IRQ is not set
> +# CONFIG_INLINE_SPIN_LOCK_IRQSAVE is not set
> +# CONFIG_INLINE_SPIN_UNLOCK is not set
> +# CONFIG_INLINE_SPIN_UNLOCK_BH is not set
> +# CONFIG_INLINE_SPIN_UNLOCK_IRQ is not set
> +# CONFIG_INLINE_SPIN_UNLOCK_IRQRESTORE is not set
> +# CONFIG_INLINE_READ_TRYLOCK is not set
> +# CONFIG_INLINE_READ_LOCK is not set
> +# CONFIG_INLINE_READ_LOCK_BH is not set
> +# CONFIG_INLINE_READ_LOCK_IRQ is not set
> +# CONFIG_INLINE_READ_LOCK_IRQSAVE is not set
> +# CONFIG_INLINE_READ_UNLOCK is not set
> +# CONFIG_INLINE_READ_UNLOCK_BH is not set
> +# CONFIG_INLINE_READ_UNLOCK_IRQ is not set
> +# CONFIG_INLINE_READ_UNLOCK_IRQRESTORE is not set
> +# CONFIG_INLINE_WRITE_TRYLOCK is not set
> +# CONFIG_INLINE_WRITE_LOCK is not set
> +# CONFIG_INLINE_WRITE_LOCK_BH is not set
> +# CONFIG_INLINE_WRITE_LOCK_IRQ is not set
> +# CONFIG_INLINE_WRITE_LOCK_IRQSAVE is not set
> +# CONFIG_INLINE_WRITE_UNLOCK is not set
> +# CONFIG_INLINE_WRITE_UNLOCK_BH is not set
> +# CONFIG_INLINE_WRITE_UNLOCK_IRQ is not set
> +# CONFIG_INLINE_WRITE_UNLOCK_IRQRESTORE is not set
> +CONFIG_MUTEX_SPIN_ON_OWNER=y
> +CONFIG_FREEZER=y
> +
> +#
> +# System Type
> +#
> +CONFIG_MMU=y
> +# CONFIG_ARCH_INTEGRATOR is not set
> +# CONFIG_ARCH_REALVIEW is not set
> +# CONFIG_ARCH_VERSATILE is not set
> +# CONFIG_ARCH_VEXPRESS is not set
> +# CONFIG_ARCH_AT91 is not set
> +# CONFIG_ARCH_BCMRING is not set
> +# CONFIG_ARCH_CLPS711X is not set
> +# CONFIG_ARCH_CNS3XXX is not set
> +# CONFIG_ARCH_GEMINI is not set
> +# CONFIG_ARCH_EBSA110 is not set
> +# CONFIG_ARCH_EP93XX is not set
> +# CONFIG_ARCH_FOOTBRIDGE is not set
> +CONFIG_ARCH_MXC=y
> +# CONFIG_ARCH_MXS is not set
> +# CONFIG_ARCH_NETX is not set
> +# CONFIG_ARCH_H720X is not set
> +# CONFIG_ARCH_IOP13XX is not set
> +# CONFIG_ARCH_IOP32X is not set
> +# CONFIG_ARCH_IOP33X is not set
> +# CONFIG_ARCH_IXP23XX is not set
> +# CONFIG_ARCH_IXP2000 is not set
> +# CONFIG_ARCH_IXP4XX is not set
> +# CONFIG_ARCH_DOVE is not set
> +# CONFIG_ARCH_KIRKWOOD is not set
> +# CONFIG_ARCH_LOKI is not set
> +# CONFIG_ARCH_LPC32XX is not set
> +# CONFIG_ARCH_MV78XX0 is not set
> +# CONFIG_ARCH_ORION5X is not set
> +# CONFIG_ARCH_MMP is not set
> +# CONFIG_ARCH_KS8695 is not set
> +# CONFIG_ARCH_W90X900 is not set
> +# CONFIG_ARCH_NUC93X is not set
> +# CONFIG_ARCH_TEGRA is not set
> +# CONFIG_ARCH_PNX4008 is not set
> +# CONFIG_ARCH_PXA is not set
> +# CONFIG_ARCH_MSM is not set
> +# CONFIG_ARCH_SHMOBILE is not set
> +# CONFIG_ARCH_RPC is not set
> +# CONFIG_ARCH_SA1100 is not set
> +# CONFIG_ARCH_S3C2410 is not set
> +# CONFIG_ARCH_S3C64XX is not set
> +# CONFIG_ARCH_S5P64X0 is not set
> +# CONFIG_ARCH_S5PC100 is not set
> +# CONFIG_ARCH_S5PV210 is not set
> +# CONFIG_ARCH_EXYNOS4 is not set
> +# CONFIG_ARCH_SHARK is not set
> +# CONFIG_ARCH_TCC_926 is not set
> +# CONFIG_ARCH_U300 is not set
> +# CONFIG_ARCH_U8500 is not set
> +# CONFIG_ARCH_NOMADIK is not set
> +# CONFIG_ARCH_DAVINCI is not set
> +# CONFIG_ARCH_OMAP is not set
> +# CONFIG_PLAT_SPEAR is not set
> +# CONFIG_ARCH_VT8500 is not set
> +CONFIG_GPIO_PCA953X=y
> +# CONFIG_KEYBOARD_GPIO_POLLED is not set
> +CONFIG_IMX_HAVE_PLATFORM_DMA=y
> +CONFIG_IMX_HAVE_PLATFORM_MXC_MLB=y
> +CONFIG_IMX_HAVE_PLATFORM_FEC=y
> +CONFIG_IMX_HAVE_PLATFORM_FLEXCAN=y
> +CONFIG_IMX_HAVE_PLATFORM_FSL_USB2_UDC=y
> +CONFIG_IMX_HAVE_PLATFORM_GPMI_NFC=y
> +CONFIG_IMX_HAVE_PLATFORM_IMX2_WDT=y
> +CONFIG_IMX_HAVE_PLATFORM_IMX_SNVS_RTC=y
> +CONFIG_IMX_HAVE_PLATFORM_IMX_CAAM=y
> +CONFIG_IMX_HAVE_PLATFORM_IMX_I2C=y
> +CONFIG_IMX_HAVE_PLATFORM_IMX_SSI=y
> +CONFIG_IMX_HAVE_PLATFORM_IMX_ESAI=y
> +CONFIG_IMX_HAVE_PLATFORM_IMX_UART=y
> +CONFIG_IMX_HAVE_PLATFORM_MXC_EHCI=y
> +CONFIG_IMX_HAVE_PLATFORM_MXC_PWM=y
> +CONFIG_IMX_HAVE_PLATFORM_SDHCI_ESDHC_IMX=y
> +CONFIG_IMX_HAVE_PLATFORM_SPI_IMX=y
> +CONFIG_IMX_HAVE_PLATFORM_IMX_IPUV3=y
> +CONFIG_IMX_HAVE_PLATFORM_IMX_VPU=y
> +CONFIG_IMX_HAVE_PLATFORM_IMX_DVFS=y
> +CONFIG_IMX_HAVE_PLATFORM_AHCI=y
> +CONFIG_IMX_HAVE_PLATFORM_IMX_OCOTP=y
> +CONFIG_IMX_HAVE_PLATFORM_IMX_VIIM=y
> +CONFIG_IMX_HAVE_PLATFORM_PERFMON=y
> +CONFIG_IMX_HAVE_PLATFORM_LDB=y
> +CONFIG_IMX_HAVE_PLATFORM_IMX_PXP=y
> +CONFIG_IMX_HAVE_PLATFORM_IMX_ELCDIF=y
> +CONFIG_IMX_HAVE_PLATFORM_IMX_EPDC=y
> +CONFIG_IMX_HAVE_PLATFORM_IMX_SPDIF=y
> +CONFIG_IMX_HAVE_PLATFORM_VIV_GPU=y
> +CONFIG_IMX_HAVE_PLATFORM_MXC_HDMI=y
> +CONFIG_IMX_HAVE_PLATFORM_IMX_ANATOP_THERMAL=y
> +CONFIG_IMX_HAVE_PLATFORM_FSL_OTG=y
> +CONFIG_IMX_HAVE_PLATFORM_FSL_USB_WAKEUP=y
> +CONFIG_IMX_HAVE_PLATFORM_IMX_PM=y
> +CONFIG_IMX_HAVE_PLATFORM_IMX_ASRC=y
> +CONFIG_IMX_HAVE_PLATFORM_IMX_MIPI_DSI=y
> +CONFIG_IMX_HAVE_PLATFORM_IMX_MIPI_CSI2=y
> +CONFIG_IMX_HAVE_PLATFORM_IMX_VDOA=y
> +CONFIG_IMX_HAVE_PLATFORM_IMX_PCIE=y
> +
> +#
> +# Freescale MXC Implementations
> +#
> +# CONFIG_ARCH_MX1 is not set
> +# CONFIG_ARCH_MX2 is not set
> +# CONFIG_ARCH_MX25 is not set
> +# CONFIG_ARCH_MX3 is not set
> +# CONFIG_ARCH_MX503 is not set
> +# CONFIG_ARCH_MX51 is not set
> +CONFIG_ARCH_MX6=y
> +CONFIG_ARCH_MX6Q=y
> +CONFIG_FORCE_MAX_ZONEORDER=14
> +CONFIG_SOC_IMX6Q=y
> +CONFIG_MACH_MX6Q_ARM2=y
> +# CONFIG_MACH_MX6SL_ARM2 is not set
> +# CONFIG_MACH_MX6SL_EVK is not set
> +# CONFIG_MACH_MX6Q_SABRELITE is not set
> +# CONFIG_MACH_MX6Q_SABRESD is not set
> +# CONFIG_MACH_MX6Q_SABREAUTO is not set
> +CONFIG_MACH_WANDBOARD=y
> +CONFIG_WANDBOARD_BASE=y
> +
> +#
> +# MX6 Options:
> +#
> +# CONFIG_IMX_PCIE is not set
> +CONFIG_USB_EHCI_ARC_H1=y
> +CONFIG_USB_FSL_ARC_OTG=y
> +# CONFIG_MX6_INTER_LDO_BYPASS is not set
> +# CONFIG_MX6_CLK_FOR_BOOTUI_TRANS is not set
> +CONFIG_ISP1504_MXC=y
> +# CONFIG_MXC_IRQ_PRIOR is not set
> +CONFIG_MXC_PWM=y
> +# CONFIG_MXC_DEBUG_BOARD is not set
> +CONFIG_MXC_REBOOT_MFGMODE=y
> +# CONFIG_MXC_REBOOT_ANDROID_CMD is not set
> +CONFIG_ARCH_MXC_IOMUX_V3=y
> +CONFIG_ARCH_MXC_AUDMUX_V2=y
> +CONFIG_IRAM_ALLOC=y
> +CONFIG_CLK_DEBUG=y
> +CONFIG_DMA_ZONE_SIZE=184
> +
> +#
> +# System MMU
> +#
> +
> +#
> +# Processor Type
> +#
> +CONFIG_CPU_V7=y
> +CONFIG_CPU_32v6K=y
> +CONFIG_CPU_32v7=y
> +CONFIG_CPU_ABRT_EV7=y
> +CONFIG_CPU_PABRT_V7=y
> +CONFIG_CPU_CACHE_V7=y
> +CONFIG_CPU_CACHE_VIPT=y
> +CONFIG_CPU_COPY_V6=y
> +CONFIG_CPU_TLB_V7=y
> +CONFIG_CPU_HAS_ASID=y
> +CONFIG_CPU_CP15=y
> +CONFIG_CPU_CP15_MMU=y
> +
> +#
> +# Processor Features
> +#
> +CONFIG_ARM_THUMB=y
> +# CONFIG_ARM_THUMBEE is not set
> +# CONFIG_SWP_EMULATE is not set
> +# CONFIG_CPU_ICACHE_DISABLE is not set
> +# CONFIG_CPU_DCACHE_DISABLE is not set
> +# CONFIG_CPU_BPREDICT_DISABLE is not set
> +CONFIG_OUTER_CACHE=y
> +CONFIG_OUTER_CACHE_SYNC=y
> +CONFIG_CACHE_L2X0=y
> +CONFIG_CACHE_PL310=y
> +CONFIG_ARM_L1_CACHE_SHIFT=5
> +CONFIG_ARM_DMA_MEM_BUFFERABLE=y
> +CONFIG_CPU_HAS_PMU=y
> +# CONFIG_ARM_ERRATA_430973 is not set
> +# CONFIG_ARM_ERRATA_458693 is not set
> +# CONFIG_ARM_ERRATA_460075 is not set
> +# CONFIG_ARM_ERRATA_742230 is not set
> +# CONFIG_ARM_ERRATA_742231 is not set
> +# CONFIG_PL310_ERRATA_588369 is not set
> +# CONFIG_ARM_ERRATA_720789 is not set
> +# CONFIG_PL310_ERRATA_727915 is not set
> +CONFIG_ARM_ERRATA_743622=y
> +CONFIG_ARM_ERRATA_751472=y
> +# CONFIG_ARM_ERRATA_753970 is not set
> +CONFIG_ARM_ERRATA_754322=y
> +# CONFIG_ARM_ERRATA_754327 is not set
> +CONFIG_ARM_GIC=y
> +
> +#
> +# Bus support
> +#
> +CONFIG_ARM_AMBA=y
> +# CONFIG_PCI_SYSCALL is not set
> +# CONFIG_ARCH_SUPPORTS_MSI is not set
> +# CONFIG_PCCARD is not set
> +CONFIG_ARM_ERRATA_764369=y
> +# CONFIG_PL310_ERRATA_769419 is not set
> +
> +#
> +# Kernel Features
> +#
> +CONFIG_TICK_ONESHOT=y
> +CONFIG_NO_HZ=y
> +CONFIG_HIGH_RES_TIMERS=y
> +CONFIG_GENERIC_CLOCKEVENTS_BUILD=y
> +CONFIG_SMP=y
> +CONFIG_SMP_ON_UP=y
> +CONFIG_HAVE_ARM_SCU=y
> +CONFIG_HAVE_ARM_TWD=y
> +# CONFIG_VMSPLIT_3G is not set
> +CONFIG_VMSPLIT_2G=y
> +# CONFIG_VMSPLIT_1G is not set
> +CONFIG_PAGE_OFFSET=0x80000000
> +CONFIG_NR_CPUS=4
> +CONFIG_HOTPLUG_CPU=y
> +CONFIG_LOCAL_TIMERS=y
> +# CONFIG_PREEMPT_NONE is not set
> +# CONFIG_PREEMPT_VOLUNTARY is not set
> +CONFIG_PREEMPT=y
> +CONFIG_HZ=100
> +# CONFIG_THUMB2_KERNEL is not set
> +CONFIG_AEABI=y
> +# CONFIG_OABI_COMPAT is not set
> +# CONFIG_ARCH_SPARSEMEM_DEFAULT is not set
> +# CONFIG_ARCH_SELECT_MEMORY_MODEL is not set
> +CONFIG_HAVE_ARCH_PFN_VALID=y
> +CONFIG_HIGHMEM=y
> +# CONFIG_HIGHPTE is not set
> +CONFIG_HW_PERF_EVENTS=y
> +CONFIG_SELECT_MEMORY_MODEL=y
> +CONFIG_FLATMEM_MANUAL=y
> +CONFIG_FLATMEM=y
> +CONFIG_FLAT_NODE_MEM_MAP=y
> +CONFIG_HAVE_MEMBLOCK=y
> +CONFIG_PAGEFLAGS_EXTENDED=y
> +CONFIG_SPLIT_PTLOCK_CPUS=4
> +CONFIG_COMPACTION=y
> +CONFIG_MIGRATION=y
> +# CONFIG_PHYS_ADDR_T_64BIT is not set
> +CONFIG_ZONE_DMA_FLAG=1
> +CONFIG_BOUNCE=y
> +CONFIG_VIRT_TO_BUS=y
> +CONFIG_KSM=y
> +CONFIG_DEFAULT_MMAP_MIN_ADDR=4096
> +# CONFIG_CLEANCACHE is not set
> +CONFIG_ALIGNMENT_TRAP=y
> +# CONFIG_UACCESS_WITH_MEMCPY is not set
> +# CONFIG_SECCOMP is not set
> +# CONFIG_CC_STACKPROTECTOR is not set
> +# CONFIG_DEPRECATED_PARAM_STRUCT is not set
> +
> +#
> +# Boot options
> +#
> +# CONFIG_USE_OF is not set
> +CONFIG_ZBOOT_ROM_TEXT=0x0
> +CONFIG_ZBOOT_ROM_BSS=0x0
> +CONFIG_CMDLINE="noinitrd console=ttymxc0,115200 root=/dev/mtdblock2 rw rootfstype=jffs2 ip=off"
> +CONFIG_CMDLINE_FROM_BOOTLOADER=y
> +# CONFIG_CMDLINE_EXTEND is not set
> +# CONFIG_CMDLINE_FORCE is not set
> +# CONFIG_XIP_KERNEL is not set
> +# CONFIG_KEXEC is not set
> +# CONFIG_CRASH_DUMP is not set
> +# CONFIG_AUTO_ZRELADDR is not set
> +
> +#
> +# CPU Power Management
> +#
> +
> +#
> +# CPU Frequency scaling
> +#
> +CONFIG_CPU_FREQ=y
> +CONFIG_CPU_FREQ_TABLE=y
> +CONFIG_CPU_FREQ_STAT=y
> +# CONFIG_CPU_FREQ_STAT_DETAILS is not set
> +# CONFIG_CPU_FREQ_DEFAULT_GOV_PERFORMANCE is not set
> +# CONFIG_CPU_FREQ_DEFAULT_GOV_POWERSAVE is not set
> +# CONFIG_CPU_FREQ_DEFAULT_GOV_USERSPACE is not set
> +# CONFIG_CPU_FREQ_DEFAULT_GOV_ONDEMAND is not set
> +# CONFIG_CPU_FREQ_DEFAULT_GOV_CONSERVATIVE is not set
> +CONFIG_CPU_FREQ_DEFAULT_GOV_INTERACTIVE=y
> +CONFIG_CPU_FREQ_GOV_PERFORMANCE=y
> +CONFIG_CPU_FREQ_GOV_POWERSAVE=y
> +CONFIG_CPU_FREQ_GOV_USERSPACE=y
> +CONFIG_CPU_FREQ_GOV_ONDEMAND=y
> +CONFIG_CPU_FREQ_GOV_INTERACTIVE=y
> +CONFIG_CPU_FREQ_GOV_CONSERVATIVE=y
> +CONFIG_CPU_FREQ_IMX=y
> +# CONFIG_CPU_IDLE is not set
> +
> +#
> +# Floating point emulation
> +#
> +
> +#
> +# At least one emulation must be selected
> +#
> +CONFIG_VFP=y
> +CONFIG_VFPv3=y
> +CONFIG_NEON=y
> +
> +#
> +# Userspace binary formats
> +#
> +CONFIG_BINFMT_ELF=y
> +# CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set
> +CONFIG_HAVE_AOUT=y
> +# CONFIG_BINFMT_AOUT is not set
> +# CONFIG_BINFMT_MISC is not set
> +
> +#
> +# Power management options
> +#
> +CONFIG_SUSPEND=y
> +# CONFIG_PM_TEST_SUSPEND is not set
> +CONFIG_SUSPEND_DEVICE_TIME_DEBUG=y
> +CONFIG_SUSPEND_FREEZER=y
> +CONFIG_PM_SLEEP=y
> +CONFIG_PM_SLEEP_SMP=y
> +CONFIG_PM_RUNTIME=y
> +CONFIG_PM=y
> +CONFIG_PM_DEBUG=y
> +# CONFIG_PM_ADVANCED_DEBUG is not set
> +CONFIG_CAN_PM_TRACE=y
> +CONFIG_APM_EMULATION=y
> +CONFIG_PM_RUNTIME_CLK=y
> +CONFIG_ARCH_SUSPEND_POSSIBLE=y
> +CONFIG_NET=y
> +
> +#
> +# Networking options
> +#
> +CONFIG_PACKET=y
> +CONFIG_UNIX=y
> +CONFIG_XFRM=y
> +# CONFIG_XFRM_USER is not set
> +# CONFIG_XFRM_SUB_POLICY is not set
> +# CONFIG_XFRM_MIGRATE is not set
> +# CONFIG_XFRM_STATISTICS is not set
> +# CONFIG_NET_KEY is not set
> +CONFIG_INET=y
> +CONFIG_IP_MULTICAST=y
> +# CONFIG_IP_ADVANCED_ROUTER is not set
> +CONFIG_IP_PNP=y
> +CONFIG_IP_PNP_DHCP=y
> +CONFIG_IP_PNP_BOOTP=y
> +# CONFIG_IP_PNP_RARP is not set
> +# CONFIG_NET_IPIP is not set
> +# CONFIG_NET_IPGRE_DEMUX is not set
> +# CONFIG_IP_MROUTE is not set
> +# CONFIG_ARPD is not set
> +# CONFIG_SYN_COOKIES is not set
> +# CONFIG_INET_AH is not set
> +# CONFIG_INET_ESP is not set
> +# CONFIG_INET_IPCOMP is not set
> +# CONFIG_INET_XFRM_TUNNEL is not set
> +# CONFIG_INET_TUNNEL is not set
> +CONFIG_INET_XFRM_MODE_TRANSPORT=y
> +CONFIG_INET_XFRM_MODE_TUNNEL=y
> +CONFIG_INET_XFRM_MODE_BEET=y
> +# CONFIG_INET_LRO is not set
> +CONFIG_INET_DIAG=y
> +CONFIG_INET_TCP_DIAG=y
> +# CONFIG_TCP_CONG_ADVANCED is not set
> +CONFIG_TCP_CONG_CUBIC=y
> +CONFIG_DEFAULT_TCP_CONG="cubic"
> +# CONFIG_TCP_MD5SIG is not set
> +# CONFIG_IPV6 is not set
> +# CONFIG_NETWORK_SECMARK is not set
> +# CONFIG_NETWORK_PHY_TIMESTAMPING is not set
> +CONFIG_NETFILTER=y
> +# CONFIG_NETFILTER_DEBUG is not set
> +CONFIG_NETFILTER_ADVANCED=y
> +
> +#
> +# Core Netfilter Configuration
> +#
> +# CONFIG_NETFILTER_NETLINK_QUEUE is not set
> +# CONFIG_NETFILTER_NETLINK_LOG is not set
> +# CONFIG_NF_CONNTRACK is not set
> +# CONFIG_NETFILTER_XTABLES is not set
> +# CONFIG_IP_VS is not set
> +
> +#
> +# IP: Netfilter Configuration
> +#
> +# CONFIG_NF_DEFRAG_IPV4 is not set
> +# CONFIG_IP_NF_QUEUE is not set
> +# CONFIG_IP_NF_IPTABLES is not set
> +# CONFIG_IP_NF_ARPTABLES is not set
> +# CONFIG_IP_DCCP is not set
> +# CONFIG_IP_SCTP is not set
> +# CONFIG_RDS is not set
> +# CONFIG_TIPC is not set
> +# CONFIG_ATM is not set
> +# CONFIG_L2TP is not set
> +# CONFIG_BRIDGE is not set
> +# CONFIG_NET_DSA is not set
> +# CONFIG_VLAN_8021Q is not set
> +# CONFIG_DECNET is not set
> +CONFIG_LLC=y
> +CONFIG_LLC2=y
> +# CONFIG_IPX is not set
> +# CONFIG_ATALK is not set
> +# CONFIG_X25 is not set
> +# CONFIG_LAPB is not set
> +# CONFIG_ECONET is not set
> +# CONFIG_WAN_ROUTER is not set
> +# CONFIG_PHONET is not set
> +# CONFIG_IEEE802154 is not set
> +# CONFIG_NET_SCHED is not set
> +# CONFIG_DCB is not set
> +# CONFIG_BATMAN_ADV is not set
> +CONFIG_RPS=y
> +CONFIG_RFS_ACCEL=y
> +CONFIG_XPS=y
> +
> +#
> +# Network testing
> +#
> +# CONFIG_NET_PKTGEN is not set
> +# CONFIG_HAMRADIO is not set
> +CONFIG_CAN=y
> +CONFIG_CAN_RAW=y
> +CONFIG_CAN_BCM=y
> +
> +#
> +# CAN Device Drivers
> +#
> +CONFIG_CAN_VCAN=y
> +# CONFIG_CAN_SLCAN is not set
> +CONFIG_CAN_DEV=y
> +CONFIG_CAN_CALC_BITTIMING=y
> +# CONFIG_CAN_MCP251X is not set
> +CONFIG_HAVE_CAN_FLEXCAN=y
> +CONFIG_CAN_FLEXCAN=y
> +# CONFIG_CAN_SJA1000 is not set
> +# CONFIG_CAN_C_CAN is not set
> +
> +#
> +# CAN USB interfaces
> +#
> +# CONFIG_CAN_EMS_USB is not set
> +# CONFIG_CAN_ESD_USB2 is not set
> +# CONFIG_CAN_SOFTING is not set
> +# CONFIG_CAN_DEBUG_DEVICES is not set
> +# CONFIG_IRDA is not set
> +CONFIG_BT=y
> +CONFIG_BT_L2CAP=y
> +CONFIG_BT_SCO=y
> +CONFIG_BT_RFCOMM=y
> +CONFIG_BT_RFCOMM_TTY=y
> +CONFIG_BT_BNEP=y
> +CONFIG_BT_BNEP_MC_FILTER=y
> +CONFIG_BT_BNEP_PROTO_FILTER=y
> +CONFIG_BT_HIDP=y
> +
> +#
> +# Bluetooth device drivers
> +#
> +CONFIG_BT_HCIBTUSB=y
> +# CONFIG_BT_HCIBTSDIO is not set
> +CONFIG_BT_HCIUART=y
> +# CONFIG_BT_HCIUART_H4 is not set
> +# CONFIG_BT_HCIUART_BCSP is not set
> +CONFIG_BT_HCIUART_ATH3K=y
> +# CONFIG_BT_HCIUART_LL is not set
> +# CONFIG_BT_HCIBCM203X is not set
> +# CONFIG_BT_HCIBPA10X is not set
> +# CONFIG_BT_HCIBFUSB is not set
> +CONFIG_BT_HCIVHCI=y
> +# CONFIG_BT_MRVL is not set
> +# CONFIG_BT_ATH3K is not set
> +# CONFIG_AF_RXRPC is not set
> +CONFIG_WIRELESS=y
> +CONFIG_WIRELESS_EXT=y
> +CONFIG_WEXT_CORE=y
> +CONFIG_WEXT_PROC=y
> +CONFIG_WEXT_SPY=y
> +CONFIG_WEXT_PRIV=y
> +CONFIG_CFG80211=y
> +# CONFIG_NL80211_TESTMODE is not set
> +# CONFIG_CFG80211_DEVELOPER_WARNINGS is not set
> +# CONFIG_CFG80211_REG_DEBUG is not set
> +CONFIG_CFG80211_DEFAULT_PS=y
> +# CONFIG_CFG80211_DEBUGFS is not set
> +# CONFIG_CFG80211_INTERNAL_REGDB is not set
> +CONFIG_CFG80211_WEXT=y
> +CONFIG_WIRELESS_EXT_SYSFS=y
> +CONFIG_LIB80211=y
> +CONFIG_LIB80211_CRYPT_WEP=y
> +CONFIG_LIB80211_CRYPT_CCMP=y
> +CONFIG_LIB80211_CRYPT_TKIP=y
> +# CONFIG_LIB80211_DEBUG is not set
> +# CONFIG_MAC80211 is not set
> +# CONFIG_WIMAX is not set
> +CONFIG_RFKILL=y
> +CONFIG_RFKILL_LEDS=y
> +CONFIG_RFKILL_INPUT=y
> +# CONFIG_RFKILL_REGULATOR is not set
> +# CONFIG_RFKILL_GPIO is not set
> +# CONFIG_NET_9P is not set
> +# CONFIG_CAIF is not set
> +# CONFIG_CEPH_LIB is not set
> +
> +#
> +# Device Drivers
> +#
> +
> +#
> +# Generic Driver Options
> +#
> +CONFIG_UEVENT_HELPER_PATH=""
> +CONFIG_DEVTMPFS=y
> +CONFIG_DEVTMPFS_MOUNT=y
> +CONFIG_STANDALONE=y
> +CONFIG_PREVENT_FIRMWARE_BUILD=y
> +CONFIG_FW_LOADER=y
> +CONFIG_FIRMWARE_IN_KERNEL=y
> +CONFIG_EXTRA_FIRMWARE=""
> +# CONFIG_SYS_HYPERVISOR is not set
> +CONFIG_CONNECTOR=y
> +CONFIG_PROC_EVENTS=y
> +CONFIG_MTD=y
> +# CONFIG_MTD_DEBUG is not set
> +# CONFIG_MTD_TESTS is not set
> +# CONFIG_MTD_REDBOOT_PARTS is not set
> +CONFIG_MTD_CMDLINE_PARTS=y
> +# CONFIG_MTD_AFS_PARTS is not set
> +# CONFIG_MTD_AR7_PARTS is not set
> +
> +#
> +# User Modules And Translation Layers
> +#
> +CONFIG_MTD_CHAR=y
> +CONFIG_MTD_BLKDEVS=y
> +CONFIG_MTD_BLOCK=y
> +# CONFIG_FTL is not set
> +# CONFIG_NFTL is not set
> +# CONFIG_INFTL is not set
> +# CONFIG_RFD_FTL is not set
> +# CONFIG_SSFDC is not set
> +# CONFIG_SM_FTL is not set
> +# CONFIG_MTD_OOPS is not set
> +# CONFIG_MTD_SWAP is not set
> +
> +#
> +# RAM/ROM/Flash chip drivers
> +#
> +CONFIG_MTD_CFI=y
> +# CONFIG_MTD_JEDECPROBE is not set
> +CONFIG_MTD_GEN_PROBE=y
> +# CONFIG_MTD_CFI_ADV_OPTIONS is not set
> +CONFIG_MTD_MAP_BANK_WIDTH_1=y
> +CONFIG_MTD_MAP_BANK_WIDTH_2=y
> +CONFIG_MTD_MAP_BANK_WIDTH_4=y
> +# CONFIG_MTD_MAP_BANK_WIDTH_8 is not set
> +# CONFIG_MTD_MAP_BANK_WIDTH_16 is not set
> +# CONFIG_MTD_MAP_BANK_WIDTH_32 is not set
> +CONFIG_MTD_CFI_I1=y
> +CONFIG_MTD_CFI_I2=y
> +# CONFIG_MTD_CFI_I4 is not set
> +# CONFIG_MTD_CFI_I8 is not set
> +# CONFIG_MTD_CFI_INTELEXT is not set
> +CONFIG_MTD_CFI_AMDSTD=y
> +# CONFIG_MTD_CFI_STAA is not set
> +CONFIG_MTD_CFI_UTIL=y
> +# CONFIG_MTD_RAM is not set
> +# CONFIG_MTD_ROM is not set
> +# CONFIG_MTD_ABSENT is not set
> +
> +#
> +# Mapping drivers for chip access
> +#
> +# CONFIG_MTD_COMPLEX_MAPPINGS is not set
> +CONFIG_MTD_PHYSMAP=y
> +# CONFIG_MTD_PHYSMAP_COMPAT is not set
> +# CONFIG_MTD_ARM_INTEGRATOR is not set
> +# CONFIG_MTD_PLATRAM is not set
> +
> +#
> +# Self-contained MTD device drivers
> +#
> +# CONFIG_MTD_DATAFLASH is not set
> +CONFIG_MTD_M25P80=y
> +CONFIG_M25PXX_USE_FAST_READ=y
> +# CONFIG_MTD_SST25L is not set
> +# CONFIG_MTD_SLRAM is not set
> +# CONFIG_MTD_PHRAM is not set
> +# CONFIG_MTD_MTDRAM is not set
> +# CONFIG_MTD_BLOCK2MTD is not set
> +
> +#
> +# Disk-On-Chip Device Drivers
> +#
> +# CONFIG_MTD_DOC2000 is not set
> +# CONFIG_MTD_DOC2001 is not set
> +# CONFIG_MTD_DOC2001PLUS is not set
> +CONFIG_MTD_NAND_ECC=y
> +# CONFIG_MTD_NAND_ECC_SMC is not set
> +CONFIG_MTD_NAND=y
> +# CONFIG_MTD_NAND_VERIFY_WRITE is not set
> +# CONFIG_MTD_NAND_ECC_BCH is not set
> +# CONFIG_MTD_SM_COMMON is not set
> +# CONFIG_MTD_NAND_MUSEUM_IDS is not set
> +# CONFIG_MTD_NAND_GPIO is not set
> +CONFIG_MTD_NAND_IDS=y
> +# CONFIG_MTD_NAND_DISKONCHIP is not set
> +# CONFIG_MTD_NAND_NANDSIM is not set
> +CONFIG_MTD_NAND_GPMI_NAND=y
> +# CONFIG_MTD_NAND_PLATFORM is not set
> +# CONFIG_MTD_ALAUDA is not set
> +# CONFIG_MTD_ONENAND is not set
> +
> +#
> +# LPDDR flash memory drivers
> +#
> +# CONFIG_MTD_LPDDR is not set
> +CONFIG_MTD_UBI=y
> +CONFIG_MTD_UBI_WL_THRESHOLD=4096
> +CONFIG_MTD_UBI_BEB_RESERVE=1
> +# CONFIG_MTD_UBI_GLUEBI is not set
> +# CONFIG_MTD_UBI_DEBUG is not set
> +# CONFIG_PARPORT is not set
> +CONFIG_BLK_DEV=y
> +# CONFIG_BLK_DEV_COW_COMMON is not set
> +CONFIG_BLK_DEV_LOOP=y
> +# CONFIG_BLK_DEV_CRYPTOLOOP is not set
> +# CONFIG_BLK_DEV_DRBD is not set
> +# CONFIG_BLK_DEV_NBD is not set
> +# CONFIG_BLK_DEV_UB is not set
> +# CONFIG_BLK_DEV_RAM is not set
> +# CONFIG_CDROM_PKTCDVD is not set
> +# CONFIG_ATA_OVER_ETH is not set
> +# CONFIG_MG_DISK is not set
> +# CONFIG_BLK_DEV_RBD is not set
> +# CONFIG_SENSORS_LIS3LV02D is not set
> +CONFIG_MISC_DEVICES=y
> +# CONFIG_AD525X_DPOT is not set
> +# CONFIG_INTEL_MID_PTI is not set
> +# CONFIG_ICS932S401 is not set
> +# CONFIG_ENCLOSURE_SERVICES is not set
> +# CONFIG_APDS9802ALS is not set
> +# CONFIG_ISL29003 is not set
> +# CONFIG_ISL29020 is not set
> +# CONFIG_SENSORS_TSL2550 is not set
> +# CONFIG_SENSORS_BH1780 is not set
> +# CONFIG_SENSORS_BH1770 is not set
> +# CONFIG_SENSORS_APDS990X is not set
> +# CONFIG_HMC6352 is not set
> +# CONFIG_DS1682 is not set
> +# CONFIG_TI_DAC7512 is not set
> +# CONFIG_BMP085 is not set
> +CONFIG_MXS_PERFMON=m
> +# CONFIG_C2PORT is not set
> +
> +#
> +# EEPROM support
> +#
> +# CONFIG_EEPROM_AT24 is not set
> +# CONFIG_EEPROM_AT25 is not set
> +# CONFIG_EEPROM_LEGACY is not set
> +# CONFIG_EEPROM_MAX6875 is not set
> +# CONFIG_EEPROM_93CX6 is not set
> +# CONFIG_IWMC3200TOP is not set
> +
> +#
> +# Texas Instruments shared transport line discipline
> +#
> +# CONFIG_TI_ST is not set
> +# CONFIG_SENSORS_LIS3_SPI is not set
> +# CONFIG_SENSORS_LIS3_I2C is not set
> +CONFIG_HAVE_IDE=y
> +# CONFIG_IDE is not set
> +
> +#
> +# SCSI device support
> +#
> +CONFIG_SCSI_MOD=y
> +# CONFIG_RAID_ATTRS is not set
> +CONFIG_SCSI=y
> +CONFIG_SCSI_DMA=y
> +# CONFIG_SCSI_TGT is not set
> +# CONFIG_SCSI_NETLINK is not set
> +CONFIG_SCSI_PROC_FS=y
> +
> +#
> +# SCSI support type (disk, tape, CD-ROM)
> +#
> +CONFIG_BLK_DEV_SD=y
> +# CONFIG_CHR_DEV_ST is not set
> +# CONFIG_CHR_DEV_OSST is not set
> +# CONFIG_BLK_DEV_SR is not set
> +# CONFIG_CHR_DEV_SG is not set
> +# CONFIG_CHR_DEV_SCH is not set
> +CONFIG_SCSI_MULTI_LUN=y
> +# CONFIG_SCSI_CONSTANTS is not set
> +# CONFIG_SCSI_LOGGING is not set
> +# CONFIG_SCSI_SCAN_ASYNC is not set
> +CONFIG_SCSI_WAIT_SCAN=m
> +
> +#
> +# SCSI Transports
> +#
> +# CONFIG_SCSI_SPI_ATTRS is not set
> +# CONFIG_SCSI_FC_ATTRS is not set
> +# CONFIG_SCSI_ISCSI_ATTRS is not set
> +# CONFIG_SCSI_SAS_ATTRS is not set
> +# CONFIG_SCSI_SAS_LIBSAS is not set
> +# CONFIG_SCSI_SRP_ATTRS is not set
> +CONFIG_SCSI_LOWLEVEL=y
> +# CONFIG_ISCSI_TCP is not set
> +# CONFIG_ISCSI_BOOT_SYSFS is not set
> +# CONFIG_LIBFC is not set
> +# CONFIG_LIBFCOE is not set
> +# CONFIG_SCSI_DEBUG is not set
> +# CONFIG_SCSI_DH is not set
> +# CONFIG_SCSI_OSD_INITIATOR is not set
> +CONFIG_ATA=y
> +# CONFIG_ATA_NONSTANDARD is not set
> +CONFIG_ATA_VERBOSE_ERROR=y
> +# CONFIG_SATA_PMP is not set
> +
> +#
> +# Controllers with non-SFF native interface
> +#
> +CONFIG_SATA_AHCI_PLATFORM=y
> +CONFIG_ATA_SFF=y
> +
> +#
> +# SFF controllers with custom DMA interface
> +#
> +CONFIG_ATA_BMDMA=y
> +
> +#
> +# SATA SFF controllers with BMDMA
> +#
> +# CONFIG_SATA_MV is not set
> +
> +#
> +# PATA SFF controllers with BMDMA
> +#
> +# CONFIG_PATA_ARASAN_CF is not set
> +
> +#
> +# PIO-only SFF controllers
> +#
> +# CONFIG_PATA_PLATFORM is not set
> +
> +#
> +# Generic fallback / legacy drivers
> +#
> +# CONFIG_MD is not set
> +# CONFIG_TARGET_CORE is not set
> +CONFIG_NETDEVICES=y
> +# CONFIG_DUMMY is not set
> +# CONFIG_BONDING is not set
> +# CONFIG_MACVLAN is not set
> +# CONFIG_EQUALIZER is not set
> +# CONFIG_TUN is not set
> +# CONFIG_VETH is not set
> +CONFIG_MII=y
> +CONFIG_PHYLIB=y
> +
> +#
> +# MII PHY device drivers
> +#
> +# CONFIG_MARVELL_PHY is not set
> +# CONFIG_DAVICOM_PHY is not set
> +# CONFIG_QSEMI_PHY is not set
> +# CONFIG_LXT_PHY is not set
> +# CONFIG_CICADA_PHY is not set
> +# CONFIG_VITESSE_PHY is not set
> +# CONFIG_SMSC_PHY is not set
> +# CONFIG_BROADCOM_PHY is not set
> +# CONFIG_ICPLUS_PHY is not set
> +# CONFIG_REALTEK_PHY is not set
> +# CONFIG_NATIONAL_PHY is not set
> +# CONFIG_STE10XP is not set
> +# CONFIG_LSI_ET1011C_PHY is not set
> +CONFIG_MICREL_PHY=y
> +# CONFIG_FIXED_PHY is not set
> +# CONFIG_MDIO_BITBANG is not set
> +CONFIG_NET_ETHERNET=y
> +# CONFIG_AX88796 is not set
> +# CONFIG_SMC91X is not set
> +# CONFIG_DM9000 is not set
> +# CONFIG_ENC28J60 is not set
> +# CONFIG_ETHOC is not set
> +# CONFIG_SMC911X is not set
> +CONFIG_SMSC911X=y
> +# CONFIG_SMSC911X_ARCH_HOOKS is not set
> +# CONFIG_DNET is not set
> +# CONFIG_IBM_NEW_EMAC_ZMII is not set
> +# CONFIG_IBM_NEW_EMAC_RGMII is not set
> +# CONFIG_IBM_NEW_EMAC_TAH is not set
> +# CONFIG_IBM_NEW_EMAC_EMAC4 is not set
> +# CONFIG_IBM_NEW_EMAC_NO_FLOW_CTRL is not set
> +# CONFIG_IBM_NEW_EMAC_MAL_CLR_ICINTSTAT is not set
> +# CONFIG_IBM_NEW_EMAC_MAL_COMMON_ERR is not set
> +# CONFIG_B44 is not set
> +# CONFIG_KS8842 is not set
> +# CONFIG_KS8851 is not set
> +# CONFIG_KS8851_MLL is not set
> +CONFIG_FEC=y
> +CONFIG_FEC_NAPI=y
> +# CONFIG_FEC_1588 is not set
> +# CONFIG_FTMAC100 is not set
> +# CONFIG_NETDEV_1000 is not set
> +# CONFIG_NETDEV_10000 is not set
> +CONFIG_WLAN=y
> +# CONFIG_USB_ZD1201 is not set
> +# CONFIG_USB_NET_RNDIS_WLAN is not set
> +CONFIG_ATH_COMMON=m
> +# CONFIG_ATH_DEBUG is not set
> +CONFIG_ATH6KL=m
> +# CONFIG_ATH6KL_DEBUG is not set
> +CONFIG_HOSTAP=y
> +# CONFIG_HOSTAP_FIRMWARE is not set
> +# CONFIG_IWM is not set
> +# CONFIG_LIBERTAS is not set
> +# CONFIG_MWIFIEX is not set
> +
> +#
> +# Enable WiMAX (Networking options) to see the WiMAX drivers
> +#
> +
> +#
> +# USB Network Adapters
> +#
> +# CONFIG_USB_CATC is not set
> +# CONFIG_USB_KAWETH is not set
> +# CONFIG_USB_PEGASUS is not set
> +# CONFIG_USB_RTL8150 is not set
> +# CONFIG_USB_USBNET is not set
> +# CONFIG_USB_HSO is not set
> +# CONFIG_USB_IPHETH is not set
> +# CONFIG_WAN is not set
> +
> +#
> +# CAIF transport drivers
> +#
> +# CONFIG_PPP is not set
> +# CONFIG_SLIP is not set
> +# CONFIG_NETCONSOLE is not set
> +# CONFIG_NETPOLL is not set
> +# CONFIG_NET_POLL_CONTROLLER is not set
> +# CONFIG_ISDN is not set
> +# CONFIG_PHONE is not set
> +
> +#
> +# Input device support
> +#
> +CONFIG_INPUT=y
> +# CONFIG_INPUT_FF_MEMLESS is not set
> +CONFIG_INPUT_POLLDEV=y
> +# CONFIG_INPUT_SPARSEKMAP is not set
> +
> +#
> +# Userland interfaces
> +#
> +CONFIG_INPUT_MOUSEDEV=y
> +CONFIG_INPUT_MOUSEDEV_PSAUX=y
> +CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024
> +CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768
> +# CONFIG_INPUT_JOYDEV is not set
> +CONFIG_INPUT_EVDEV=y
> +# CONFIG_INPUT_EVBUG is not set
> +# CONFIG_INPUT_APMPOWER is not set
> +
> +#
> +# Input Device Drivers
> +#
> +CONFIG_INPUT_KEYBOARD=y
> +# CONFIG_KEYBOARD_ADP5588 is not set
> +# CONFIG_KEYBOARD_ADP5589 is not set
> +CONFIG_KEYBOARD_ATKBD=y
> +# CONFIG_KEYBOARD_QT1070 is not set
> +# CONFIG_KEYBOARD_QT2160 is not set
> +# CONFIG_KEYBOARD_LKKBD is not set
> +CONFIG_KEYBOARD_GPIO=y
> +# CONFIG_KEYBOARD_TCA6416 is not set
> +# CONFIG_KEYBOARD_MATRIX is not set
> +# CONFIG_KEYBOARD_LM8323 is not set
> +# CONFIG_KEYBOARD_MAX7359 is not set
> +# CONFIG_KEYBOARD_MCS is not set
> +# CONFIG_KEYBOARD_MPR121 is not set
> +# CONFIG_KEYBOARD_IMX is not set
> +# CONFIG_KEYBOARD_NEWTON is not set
> +# CONFIG_KEYBOARD_OPENCORES is not set
> +# CONFIG_KEYBOARD_STOWAWAY is not set
> +# CONFIG_KEYBOARD_SUNKBD is not set
> +# CONFIG_KEYBOARD_XTKBD is not set
> +# CONFIG_INPUT_MOUSE is not set
> +# CONFIG_INPUT_JOYSTICK is not set
> +# CONFIG_INPUT_TABLET is not set
> +CONFIG_INPUT_TOUCHSCREEN=y
> +# CONFIG_TOUCHSCREEN_ADS7846 is not set
> +# CONFIG_TOUCHSCREEN_AD7877 is not set
> +# CONFIG_TOUCHSCREEN_AD7879 is not set
> +# CONFIG_TOUCHSCREEN_ATMEL_MXT is not set
> +# CONFIG_TOUCHSCREEN_BU21013 is not set
> +# CONFIG_TOUCHSCREEN_CY8CTMG110 is not set
> +# CONFIG_TOUCHSCREEN_DYNAPRO is not set
> +# CONFIG_TOUCHSCREEN_HAMPSHIRE is not set
> +# CONFIG_TOUCHSCREEN_EETI is not set
> +CONFIG_TOUCHSCREEN_EGALAX=y
> +CONFIG_TOUCHSCREEN_ELAN=y
> +CONFIG_TOUCHSCREEN_EGALAX_SINGLE_TOUCH=y
> +# CONFIG_TOUCHSCREEN_FUJITSU is not set
> +# CONFIG_TOUCHSCREEN_GUNZE is not set
> +# CONFIG_TOUCHSCREEN_ELO is not set
> +# CONFIG_TOUCHSCREEN_WACOM_W8001 is not set
> +CONFIG_TOUCHSCREEN_MAX11801=y
> +# CONFIG_TOUCHSCREEN_MCS5000 is not set
> +# CONFIG_TOUCHSCREEN_MTOUCH is not set
> +# CONFIG_TOUCHSCREEN_INEXIO is not set
> +# CONFIG_TOUCHSCREEN_MK712 is not set
> +# CONFIG_TOUCHSCREEN_PENMOUNT is not set
> +# CONFIG_TOUCHSCREEN_TOUCHRIGHT is not set
> +# CONFIG_TOUCHSCREEN_TOUCHWIN is not set
> +# CONFIG_TOUCHSCREEN_WM97XX is not set
> +# CONFIG_TOUCHSCREEN_USB_COMPOSITE is not set
> +# CONFIG_TOUCHSCREEN_NOVATEK is not set
> +# CONFIG_TOUCHSCREEN_TOUCHIT213 is not set
> +# CONFIG_TOUCHSCREEN_TSC2005 is not set
> +# CONFIG_TOUCHSCREEN_TSC2007 is not set
> +# CONFIG_TOUCHSCREEN_W90X900 is not set
> +# CONFIG_TOUCHSCREEN_ST1232 is not set
> +# CONFIG_TOUCHSCREEN_P1003 is not set
> +# CONFIG_TOUCHSCREEN_TPS6507X is not set
> +CONFIG_INPUT_MISC=y
> +# CONFIG_INPUT_AD714X is not set
> +# CONFIG_INPUT_ATI_REMOTE is not set
> +# CONFIG_INPUT_ATI_REMOTE2 is not set
> +# CONFIG_INPUT_KEYSPAN_REMOTE is not set
> +# CONFIG_INPUT_POWERMATE is not set
> +# CONFIG_INPUT_YEALINK is not set
> +# CONFIG_INPUT_CM109 is not set
> +CONFIG_INPUT_UINPUT=y
> +# CONFIG_INPUT_PCF8574 is not set
> +# CONFIG_INPUT_PWM_BEEPER is not set
> +# CONFIG_INPUT_GPIO_ROTARY_ENCODER is not set
> +# CONFIG_INPUT_ADXL34X is not set
> +# CONFIG_INPUT_CMA3000 is not set
> +CONFIG_INPUT_ISL29023=y
> +
> +#
> +# Hardware I/O ports
> +#
> +CONFIG_SERIO=y
> +CONFIG_SERIO_SERPORT=y
> +# CONFIG_SERIO_AMBAKMI is not set
> +CONFIG_SERIO_LIBPS2=y
> +# CONFIG_SERIO_RAW is not set
> +# CONFIG_SERIO_ALTERA_PS2 is not set
> +# CONFIG_SERIO_PS2MULT is not set
> +# CONFIG_GAMEPORT is not set
> +
> +#
> +# Character devices
> +#
> +CONFIG_VT=y
> +CONFIG_CONSOLE_TRANSLATIONS=y
> +CONFIG_VT_CONSOLE=y
> +CONFIG_HW_CONSOLE=y
> +CONFIG_VT_HW_CONSOLE_BINDING=y
> +CONFIG_UNIX98_PTYS=y
> +# CONFIG_DEVPTS_MULTIPLE_INSTANCES is not set
> +CONFIG_LEGACY_PTYS=y
> +CONFIG_LEGACY_PTY_COUNT=256
> +# CONFIG_SERIAL_NONSTANDARD is not set
> +# CONFIG_N_GSM is not set
> +# CONFIG_TRACE_SINK is not set
> +CONFIG_DEVKMEM=y
> +
> +#
> +# Serial drivers
> +#
> +# CONFIG_SERIAL_8250 is not set
> +
> +#
> +# Non-8250 serial port support
> +#
> +# CONFIG_SERIAL_AMBA_PL010 is not set
> +# CONFIG_SERIAL_AMBA_PL011 is not set
> +# CONFIG_SERIAL_MAX3100 is not set
> +# CONFIG_SERIAL_MAX3107 is not set
> +CONFIG_SERIAL_IMX=y
> +CONFIG_SERIAL_IMX_CONSOLE=y
> +CONFIG_SERIAL_CORE=y
> +CONFIG_SERIAL_CORE_CONSOLE=y
> +# CONFIG_SERIAL_TIMBERDALE is not set
> +# CONFIG_SERIAL_ALTERA_JTAGUART is not set
> +# CONFIG_SERIAL_ALTERA_UART is not set
> +# CONFIG_SERIAL_IFX6X60 is not set
> +# CONFIG_SERIAL_XILINX_PS_UART is not set
> +# CONFIG_TTY_PRINTK is not set
> +CONFIG_FSL_OTP=y
> +# CONFIG_HVC_DCC is not set
> +# CONFIG_IPMI_HANDLER is not set
> +CONFIG_HW_RANDOM=y
> +# CONFIG_HW_RANDOM_TIMERIOMEM is not set
> +# CONFIG_R3964 is not set
> +# CONFIG_RAW_DRIVER is not set
> +# CONFIG_TCG_TPM is not set
> +# CONFIG_RAMOOPS is not set
> +CONFIG_MXS_VIIM=y
> +CONFIG_I2C=y
> +CONFIG_I2C_BOARDINFO=y
> +CONFIG_I2C_COMPAT=y
> +CONFIG_I2C_CHARDEV=y
> +# CONFIG_I2C_MUX is not set
> +CONFIG_I2C_HELPER_AUTO=y
> +CONFIG_I2C_ALGOBIT=m
> +
> +#
> +# I2C Hardware Bus support
> +#
> +
> +#
> +# I2C system bus drivers (mostly embedded / system-on-chip)
> +#
> +# CONFIG_I2C_DESIGNWARE is not set
> +# CONFIG_I2C_GPIO is not set
> +CONFIG_I2C_IMX=y
> +# CONFIG_I2C_OCORES is not set
> +# CONFIG_I2C_PCA_PLATFORM is not set
> +# CONFIG_I2C_PXA_PCI is not set
> +# CONFIG_I2C_SIMTEC is not set
> +# CONFIG_I2C_XILINX is not set
> +
> +#
> +# External I2C/SMBus adapter drivers
> +#
> +# CONFIG_I2C_DIOLAN_U2C is not set
> +# CONFIG_I2C_PARPORT_LIGHT is not set
> +# CONFIG_I2C_TAOS_EVM is not set
> +# CONFIG_I2C_TINY_USB is not set
> +
> +#
> +# Other I2C/SMBus bus drivers
> +#
> +# CONFIG_I2C_STUB is not set
> +# CONFIG_I2C_DEBUG_CORE is not set
> +# CONFIG_I2C_DEBUG_ALGO is not set
> +# CONFIG_I2C_DEBUG_BUS is not set
> +CONFIG_SPI=y
> +CONFIG_SPI_MASTER=y
> +
> +#
> +# SPI Master Controller Drivers
> +#
> +# CONFIG_SPI_ALTERA is not set
> +CONFIG_SPI_BITBANG=y
> +# CONFIG_SPI_GPIO is not set
> +CONFIG_SPI_IMX_VER_2_3=y
> +CONFIG_SPI_IMX=y
> +# CONFIG_SPI_OC_TINY is not set
> +# CONFIG_SPI_PL022 is not set
> +# CONFIG_SPI_PXA2XX_PCI is not set
> +# CONFIG_SPI_XILINX is not set
> +# CONFIG_SPI_DESIGNWARE is not set
> +
> +#
> +# SPI Protocol Masters
> +#
> +# CONFIG_SPI_SPIDEV is not set
> +# CONFIG_SPI_TLE62X0 is not set
> +
> +#
> +# PPS support
> +#
> +# CONFIG_PPS is not set
> +
> +#
> +# PPS generators support
> +#
> +
> +#
> +# PTP clock support
> +#
> +
> +#
> +# Enable Device Drivers -> PPS to see the PTP clock options.
> +#
> +CONFIG_ARCH_REQUIRE_GPIOLIB=y
> +CONFIG_GPIOLIB=y
> +CONFIG_GPIO_SYSFS=y
> +
> +#
> +# Memory mapped GPIO drivers:
> +#
> +# CONFIG_GPIO_BASIC_MMIO is not set
> +# CONFIG_GPIO_IT8761E is not set
> +# CONFIG_GPIO_PL061 is not set
> +
> +#
> +# I2C GPIO expanders:
> +#
> +# CONFIG_GPIO_MAX7300 is not set
> +# CONFIG_GPIO_MAX732X is not set
> +# CONFIG_GPIO_PCA953X_IRQ is not set
> +# CONFIG_GPIO_PCF857X is not set
> +# CONFIG_GPIO_SX150X is not set
> +# CONFIG_GPIO_WM8994 is not set
> +# CONFIG_GPIO_ADP5588 is not set
> +
> +#
> +# PCI GPIO expanders:
> +#
> +
> +#
> +# SPI GPIO expanders:
> +#
> +# CONFIG_GPIO_MAX7301 is not set
> +# CONFIG_GPIO_MCP23S08 is not set
> +# CONFIG_GPIO_MC33880 is not set
> +# CONFIG_GPIO_74X164 is not set
> +
> +#
> +# AC97 GPIO expanders:
> +#
> +
> +#
> +# MODULbus GPIO expanders:
> +#
> +# CONFIG_W1 is not set
> +CONFIG_POWER_SUPPLY=y
> +# CONFIG_POWER_SUPPLY_DEBUG is not set
> +# CONFIG_PDA_POWER is not set
> +# CONFIG_APM_POWER is not set
> +# CONFIG_TEST_POWER is not set
> +# CONFIG_BATTERY_DS2780 is not set
> +# CONFIG_BATTERY_DS2782 is not set
> +# CONFIG_BATTERY_BQ20Z75 is not set
> +# CONFIG_BATTERY_BQ27x00 is not set
> +# CONFIG_BATTERY_MAX17040 is not set
> +# CONFIG_BATTERY_MAX17042 is not set
> +# CONFIG_CHARGER_ISP1704 is not set
> +# CONFIG_CHARGER_MAX8903 is not set
> +CONFIG_SABRESD_MAX8903=y
> +# CONFIG_CHARGER_GPIO is not set
> +CONFIG_HWMON=y
> +# CONFIG_HWMON_VID is not set
> +# CONFIG_HWMON_DEBUG_CHIP is not set
> +
> +#
> +# Native drivers
> +#
> +# CONFIG_SENSORS_AD7414 is not set
> +# CONFIG_SENSORS_AD7418 is not set
> +# CONFIG_SENSORS_ADCXX is not set
> +# CONFIG_SENSORS_ADM1021 is not set
> +# CONFIG_SENSORS_ADM1025 is not set
> +# CONFIG_SENSORS_ADM1026 is not set
> +# CONFIG_SENSORS_ADM1029 is not set
> +# CONFIG_SENSORS_ADM1031 is not set
> +# CONFIG_SENSORS_ADM9240 is not set
> +# CONFIG_SENSORS_ADT7411 is not set
> +# CONFIG_SENSORS_ADT7462 is not set
> +# CONFIG_SENSORS_ADT7470 is not set
> +# CONFIG_SENSORS_ADT7475 is not set
> +# CONFIG_SENSORS_ASC7621 is not set
> +# CONFIG_SENSORS_ATXP1 is not set
> +# CONFIG_SENSORS_DS620 is not set
> +# CONFIG_SENSORS_DS1621 is not set
> +# CONFIG_SENSORS_F71805F is not set
> +# CONFIG_SENSORS_F71882FG is not set
> +# CONFIG_SENSORS_F75375S is not set
> +# CONFIG_SENSORS_G760A is not set
> +# CONFIG_SENSORS_GL518SM is not set
> +# CONFIG_SENSORS_GL520SM is not set
> +# CONFIG_SENSORS_GPIO_FAN is not set
> +# CONFIG_SENSORS_IT87 is not set
> +# CONFIG_SENSORS_JC42 is not set
> +# CONFIG_SENSORS_LINEAGE is not set
> +# CONFIG_SENSORS_LM63 is not set
> +# CONFIG_SENSORS_LM70 is not set
> +# CONFIG_SENSORS_LM73 is not set
> +# CONFIG_SENSORS_LM75 is not set
> +# CONFIG_SENSORS_LM77 is not set
> +# CONFIG_SENSORS_LM78 is not set
> +# CONFIG_SENSORS_LM80 is not set
> +# CONFIG_SENSORS_LM83 is not set
> +# CONFIG_SENSORS_LM85 is not set
> +# CONFIG_SENSORS_LM87 is not set
> +# CONFIG_SENSORS_LM90 is not set
> +# CONFIG_SENSORS_LM92 is not set
> +# CONFIG_SENSORS_LM93 is not set
> +# CONFIG_SENSORS_LTC4151 is not set
> +# CONFIG_SENSORS_LTC4215 is not set
> +# CONFIG_SENSORS_LTC4245 is not set
> +# CONFIG_SENSORS_LTC4261 is not set
> +# CONFIG_SENSORS_LM95241 is not set
> +# CONFIG_SENSORS_MAX1111 is not set
> +# CONFIG_SENSORS_MAX16065 is not set
> +# CONFIG_SENSORS_MAX1619 is not set
> +# CONFIG_SENSORS_MAX6639 is not set
> +# CONFIG_SENSORS_MAX6642 is not set
> +CONFIG_SENSORS_MAX17135=y
> +# CONFIG_SENSORS_MAX6650 is not set
> +# CONFIG_SENSORS_PC87360 is not set
> +# CONFIG_SENSORS_PC87427 is not set
> +# CONFIG_SENSORS_PCF8591 is not set
> +# CONFIG_PMBUS is not set
> +# CONFIG_SENSORS_SHT15 is not set
> +# CONFIG_SENSORS_SHT21 is not set
> +# CONFIG_SENSORS_SMM665 is not set
> +# CONFIG_SENSORS_DME1737 is not set
> +# CONFIG_SENSORS_EMC1403 is not set
> +# CONFIG_SENSORS_EMC2103 is not set
> +# CONFIG_SENSORS_EMC6W201 is not set
> +# CONFIG_SENSORS_SMSC47M1 is not set
> +# CONFIG_SENSORS_SMSC47M192 is not set
> +# CONFIG_SENSORS_SMSC47B397 is not set
> +# CONFIG_SENSORS_SCH5627 is not set
> +# CONFIG_SENSORS_ADS1015 is not set
> +# CONFIG_SENSORS_ADS7828 is not set
> +# CONFIG_SENSORS_ADS7871 is not set
> +# CONFIG_SENSORS_AMC6821 is not set
> +# CONFIG_SENSORS_THMC50 is not set
> +# CONFIG_SENSORS_TMP102 is not set
> +# CONFIG_SENSORS_TMP401 is not set
> +# CONFIG_SENSORS_TMP421 is not set
> +# CONFIG_SENSORS_VT1211 is not set
> +# CONFIG_SENSORS_W83781D is not set
> +# CONFIG_SENSORS_W83791D is not set
> +# CONFIG_SENSORS_W83792D is not set
> +# CONFIG_SENSORS_W83793 is not set
> +# CONFIG_SENSORS_W83795 is not set
> +# CONFIG_SENSORS_W83L785TS is not set
> +# CONFIG_SENSORS_W83L786NG is not set
> +# CONFIG_SENSORS_W83627HF is not set
> +# CONFIG_SENSORS_W83627EHF is not set
> +CONFIG_SENSORS_MAG3110=y
> +# CONFIG_MXC_MMA8450 is not set
> +CONFIG_MXC_MMA8451=y
> +CONFIG_THERMAL=y
> +# CONFIG_THERMAL_HWMON is not set
> +CONFIG_WATCHDOG=y
> +CONFIG_WATCHDOG_NOWAYOUT=y
> +
> +#
> +# Watchdog Device Drivers
> +#
> +# CONFIG_SOFT_WATCHDOG is not set
> +# CONFIG_ARM_SP805_WATCHDOG is not set
> +# CONFIG_MPCORE_WATCHDOG is not set
> +# CONFIG_MAX63XX_WATCHDOG is not set
> +CONFIG_IMX2_WDT=y
> +
> +#
> +# USB-based Watchdog Cards
> +#
> +# CONFIG_USBPCWATCHDOG is not set
> +CONFIG_SSB_POSSIBLE=y
> +
> +#
> +# Sonics Silicon Backplane
> +#
> +# CONFIG_SSB is not set
> +CONFIG_BCMA_POSSIBLE=y
> +
> +#
> +# Broadcom specific AMBA
> +#
> +# CONFIG_BCMA is not set
> +CONFIG_MFD_SUPPORT=y
> +CONFIG_MFD_CORE=y
> +# CONFIG_MFD_88PM860X is not set
> +# CONFIG_MFD_SM501 is not set
> +# CONFIG_MFD_ASIC3 is not set
> +# CONFIG_HTC_EGPIO is not set
> +# CONFIG_HTC_PASIC3 is not set
> +# CONFIG_HTC_I2CPLD is not set
> +# CONFIG_UCB1400_CORE is not set
> +# CONFIG_TPS6105X is not set
> +# CONFIG_TPS65010 is not set
> +# CONFIG_TPS6507X is not set
> +# CONFIG_MFD_TPS6586X is not set
> +# CONFIG_TWL4030_CORE is not set
> +# CONFIG_MFD_STMPE is not set
> +# CONFIG_MFD_TC3589X is not set
> +# CONFIG_MFD_TMIO is not set
> +# CONFIG_MFD_T7L66XB is not set
> +# CONFIG_MFD_TC6387XB is not set
> +# CONFIG_MFD_TC6393XB is not set
> +# CONFIG_PMIC_DA903X is not set
> +# CONFIG_PMIC_ADP5520 is not set
> +# CONFIG_MFD_MAX8925 is not set
> +# CONFIG_MFD_MAX8997 is not set
> +# CONFIG_MFD_MAX8998 is not set
> +# CONFIG_MFD_WM8400 is not set
> +# CONFIG_MFD_WM831X_I2C is not set
> +# CONFIG_MFD_WM831X_SPI is not set
> +# CONFIG_MFD_WM8350_I2C is not set
> +CONFIG_MFD_WM8994=y
> +# CONFIG_MFD_PCF50633 is not set
> +# CONFIG_PMIC_DIALOG is not set
> +# CONFIG_MFD_MC_PMIC is not set
> +# CONFIG_MFD_MC34708 is not set
> +CONFIG_MFD_PFUZE=y
> +# CONFIG_MFD_MC13XXX is not set
> +# CONFIG_ABX500_CORE is not set
> +# CONFIG_EZX_PCAP is not set
> +# CONFIG_MFD_WL1273_CORE is not set
> +# CONFIG_MFD_TPS65910 is not set
> +CONFIG_MFD_MAX17135=y
> +CONFIG_MFD_MXC_HDMI=y
> +CONFIG_REGULATOR=y
> +# CONFIG_REGULATOR_DEBUG is not set
> +# CONFIG_REGULATOR_DUMMY is not set
> +CONFIG_REGULATOR_FIXED_VOLTAGE=y
> +# CONFIG_REGULATOR_VIRTUAL_CONSUMER is not set
> +# CONFIG_REGULATOR_USERSPACE_CONSUMER is not set
> +# CONFIG_REGULATOR_BQ24022 is not set
> +# CONFIG_REGULATOR_MAX1586 is not set
> +# CONFIG_REGULATOR_MAX8649 is not set
> +# CONFIG_REGULATOR_MAX8660 is not set
> +# CONFIG_REGULATOR_MAX8952 is not set
> +# CONFIG_REGULATOR_WM8994 is not set
> +# CONFIG_REGULATOR_LP3971 is not set
> +# CONFIG_REGULATOR_LP3972 is not set
> +# CONFIG_REGULATOR_MC34708 is not set
> +CONFIG_REGULATOR_PFUZE100=y
> +# CONFIG_REGULATOR_TPS65023 is not set
> +# CONFIG_REGULATOR_TPS6507X is not set
> +# CONFIG_REGULATOR_ISL6271A is not set
> +# CONFIG_REGULATOR_AD5398 is not set
> +CONFIG_REGULATOR_ANATOP=y
> +# CONFIG_REGULATOR_TPS6524X is not set
> +CONFIG_REGULATOR_MAX17135=y
> +CONFIG_MEDIA_SUPPORT=y
> +
> +#
> +# Multimedia core support
> +#
> +# CONFIG_MEDIA_CONTROLLER is not set
> +CONFIG_VIDEO_DEV=y
> +CONFIG_VIDEO_V4L2_COMMON=y
> +# CONFIG_DVB_CORE is not set
> +CONFIG_VIDEO_MEDIA=y
> +
> +#
> +# Multimedia drivers
> +#
> +# CONFIG_RC_CORE is not set
> +# CONFIG_MEDIA_ATTACH is not set
> +CONFIG_MEDIA_TUNER=y
> +# CONFIG_MEDIA_TUNER_CUSTOMISE is not set
> +CONFIG_MEDIA_TUNER_SIMPLE=y
> +CONFIG_MEDIA_TUNER_TDA8290=y
> +CONFIG_MEDIA_TUNER_TDA827X=y
> +CONFIG_MEDIA_TUNER_TDA18271=y
> +CONFIG_MEDIA_TUNER_TDA9887=y
> +CONFIG_MEDIA_TUNER_TEA5761=y
> +CONFIG_MEDIA_TUNER_TEA5767=y
> +CONFIG_MEDIA_TUNER_MT20XX=y
> +CONFIG_MEDIA_TUNER_XC2028=y
> +CONFIG_MEDIA_TUNER_XC5000=y
> +CONFIG_MEDIA_TUNER_MC44S803=y
> +CONFIG_VIDEO_V4L2=y
> +CONFIG_VIDEOBUF_GEN=y
> +CONFIG_VIDEOBUF_DMA_CONTIG=y
> +CONFIG_VIDEO_CAPTURE_DRIVERS=y
> +# CONFIG_VIDEO_ADV_DEBUG is not set
> +# CONFIG_VIDEO_FIXED_MINOR_RANGES is not set
> +# CONFIG_VIDEO_HELPER_CHIPS_AUTO is not set
> +
> +#
> +# Encoders, decoders, sensors and other helper chips
> +#
> +
> +#
> +# Audio decoders, processors and mixers
> +#
> +# CONFIG_VIDEO_TVAUDIO is not set
> +# CONFIG_VIDEO_TDA7432 is not set
> +# CONFIG_VIDEO_TDA9840 is not set
> +# CONFIG_VIDEO_TEA6415C is not set
> +# CONFIG_VIDEO_TEA6420 is not set
> +# CONFIG_VIDEO_MSP3400 is not set
> +# CONFIG_VIDEO_CS5345 is not set
> +# CONFIG_VIDEO_CS53L32A is not set
> +# CONFIG_VIDEO_TLV320AIC23B is not set
> +# CONFIG_VIDEO_WM8775 is not set
> +# CONFIG_VIDEO_WM8739 is not set
> +# CONFIG_VIDEO_VP27SMPX is not set
> +
> +#
> +# RDS decoders
> +#
> +# CONFIG_VIDEO_SAA6588 is not set
> +
> +#
> +# Video decoders
> +#
> +# CONFIG_VIDEO_ADV7180 is not set
> +# CONFIG_VIDEO_BT819 is not set
> +# CONFIG_VIDEO_BT856 is not set
> +# CONFIG_VIDEO_BT866 is not set
> +# CONFIG_VIDEO_KS0127 is not set
> +# CONFIG_VIDEO_SAA7110 is not set
> +# CONFIG_VIDEO_SAA711X is not set
> +# CONFIG_VIDEO_SAA7191 is not set
> +# CONFIG_VIDEO_TVP514X is not set
> +# CONFIG_VIDEO_TVP5150 is not set
> +# CONFIG_VIDEO_TVP7002 is not set
> +# CONFIG_VIDEO_VPX3220 is not set
> +
> +#
> +# Video and audio decoders
> +#
> +# CONFIG_VIDEO_SAA717X is not set
> +# CONFIG_VIDEO_CX25840 is not set
> +
> +#
> +# MPEG video encoders
> +#
> +# CONFIG_VIDEO_CX2341X is not set
> +
> +#
> +# Video encoders
> +#
> +# CONFIG_VIDEO_SAA7127 is not set
> +# CONFIG_VIDEO_SAA7185 is not set
> +# CONFIG_VIDEO_ADV7170 is not set
> +# CONFIG_VIDEO_ADV7175 is not set
> +# CONFIG_VIDEO_ADV7343 is not set
> +# CONFIG_VIDEO_AK881X is not set
> +
> +#
> +# Camera sensor devices
> +#
> +# CONFIG_VIDEO_OV7670 is not set
> +# CONFIG_VIDEO_MT9V011 is not set
> +# CONFIG_VIDEO_TCM825X is not set
> +
> +#
> +# Video improvement chips
> +#
> +# CONFIG_VIDEO_UPD64031A is not set
> +# CONFIG_VIDEO_UPD64083 is not set
> +
> +#
> +# Miscelaneous helper chips
> +#
> +# CONFIG_VIDEO_THS7303 is not set
> +# CONFIG_VIDEO_M52790 is not set
> +# CONFIG_VIDEO_VIVI is not set
> +CONFIG_VIDEO_MXC_CAMERA=m
> +
> +#
> +# MXC Camera/V4L2 PRP Features support
> +#
> +CONFIG_VIDEO_MXC_IPU_CAMERA=y
> +# CONFIG_VIDEO_MXC_CSI_CAMERA is not set
> +# CONFIG_MXC_CAMERA_MICRON111 is not set
> +# CONFIG_MXC_CAMERA_OV2640 is not set
> +CONFIG_MXC_CAMERA_OV3640=m
> +CONFIG_MXC_CAMERA_OV5640=m
> +CONFIG_MXC_CAMERA_OV8820_MIPI=m
> +CONFIG_MXC_CAMERA_OV5642=m
> +CONFIG_MXC_TVIN_ADV7180=m
> +CONFIG_MXC_CAMERA_OV5640_MIPI=m
> +# CONFIG_MXC_MIPI_CSI2_TVIN_ADV7280 is not set
> +CONFIG_MXC_CAMERA_SENSOR_CLK=m
> +CONFIG_MXC_IPU_DEVICE_QUEUE_SDC=m
> +CONFIG_MXC_IPU_PRP_ENC=m
> +CONFIG_MXC_IPU_CSI_ENC=m
> +CONFIG_VIDEO_MXC_OUTPUT=y
> +CONFIG_VIDEO_MXC_IPU_OUTPUT=y
> +# CONFIG_VIDEO_MXC_IPUV1_WVGA_OUTPUT is not set
> +# CONFIG_VIDEO_MXC_OPL is not set
> +# CONFIG_VIDEO_CPIA2 is not set
> +# CONFIG_VIDEO_TIMBERDALE is not set
> +# CONFIG_VIDEO_SR030PC30 is not set
> +# CONFIG_VIDEO_NOON010PC30 is not set
> +# CONFIG_SOC_CAMERA is not set
> +CONFIG_V4L_USB_DRIVERS=y
> +CONFIG_USB_VIDEO_CLASS=m
> +CONFIG_USB_VIDEO_CLASS_INPUT_EVDEV=y
> +CONFIG_USB_GSPCA=m
> +# CONFIG_USB_M5602 is not set
> +# CONFIG_USB_STV06XX is not set
> +# CONFIG_USB_GL860 is not set
> +# CONFIG_USB_GSPCA_BENQ is not set
> +# CONFIG_USB_GSPCA_CONEX is not set
> +# CONFIG_USB_GSPCA_CPIA1 is not set
> +# CONFIG_USB_GSPCA_ETOMS is not set
> +# CONFIG_USB_GSPCA_FINEPIX is not set
> +# CONFIG_USB_GSPCA_JEILINJ is not set
> +# CONFIG_USB_GSPCA_KINECT is not set
> +# CONFIG_USB_GSPCA_KONICA is not set
> +# CONFIG_USB_GSPCA_MARS is not set
> +# CONFIG_USB_GSPCA_MR97310A is not set
> +# CONFIG_USB_GSPCA_NW80X is not set
> +# CONFIG_USB_GSPCA_OV519 is not set
> +# CONFIG_USB_GSPCA_OV534 is not set
> +# CONFIG_USB_GSPCA_OV534_9 is not set
> +# CONFIG_USB_GSPCA_PAC207 is not set
> +# CONFIG_USB_GSPCA_PAC7302 is not set
> +# CONFIG_USB_GSPCA_PAC7311 is not set
> +# CONFIG_USB_GSPCA_SN9C2028 is not set
> +# CONFIG_USB_GSPCA_SN9C20X is not set
> +# CONFIG_USB_GSPCA_SONIXB is not set
> +# CONFIG_USB_GSPCA_SONIXJ is not set
> +# CONFIG_USB_GSPCA_SPCA500 is not set
> +# CONFIG_USB_GSPCA_SPCA501 is not set
> +# CONFIG_USB_GSPCA_SPCA505 is not set
> +# CONFIG_USB_GSPCA_SPCA506 is not set
> +# CONFIG_USB_GSPCA_SPCA508 is not set
> +# CONFIG_USB_GSPCA_SPCA561 is not set
> +# CONFIG_USB_GSPCA_SPCA1528 is not set
> +# CONFIG_USB_GSPCA_SQ905 is not set
> +# CONFIG_USB_GSPCA_SQ905C is not set
> +# CONFIG_USB_GSPCA_SQ930X is not set
> +# CONFIG_USB_GSPCA_STK014 is not set
> +# CONFIG_USB_GSPCA_STV0680 is not set
> +# CONFIG_USB_GSPCA_SUNPLUS is not set
> +# CONFIG_USB_GSPCA_T613 is not set
> +# CONFIG_USB_GSPCA_TV8532 is not set
> +# CONFIG_USB_GSPCA_VC032X is not set
> +# CONFIG_USB_GSPCA_VICAM is not set
> +# CONFIG_USB_GSPCA_XIRLINK_CIT is not set
> +# CONFIG_USB_GSPCA_ZC3XX is not set
> +# CONFIG_VIDEO_PVRUSB2 is not set
> +# CONFIG_VIDEO_HDPVR is not set
> +# CONFIG_VIDEO_USBVISION is not set
> +# CONFIG_USB_ET61X251 is not set
> +# CONFIG_USB_SN9C102 is not set
> +# CONFIG_USB_PWC is not set
> +# CONFIG_USB_ZR364XX is not set
> +# CONFIG_USB_STKWEBCAM is not set
> +# CONFIG_USB_S2255 is not set
> +# CONFIG_V4L_MEM2MEM_DRIVERS is not set
> +# CONFIG_RADIO_ADAPTERS is not set
> +
> +#
> +# Graphics support
> +#
> +CONFIG_DRM=m
> +CONFIG_DRM_VIVANTE=m
> +# CONFIG_VGASTATE is not set
> +# CONFIG_VIDEO_OUTPUT_CONTROL is not set
> +CONFIG_FB=y
> +# CONFIG_FIRMWARE_EDID is not set
> +# CONFIG_FB_DDC is not set
> +# CONFIG_FB_BOOT_VESA_SUPPORT is not set
> +CONFIG_FB_CFB_FILLRECT=y
> +CONFIG_FB_CFB_COPYAREA=y
> +CONFIG_FB_CFB_IMAGEBLIT=y
> +# CONFIG_FB_CFB_REV_PIXELS_IN_BYTE is not set
> +# CONFIG_FB_SYS_FILLRECT is not set
> +# CONFIG_FB_SYS_COPYAREA is not set
> +# CONFIG_FB_SYS_IMAGEBLIT is not set
> +# CONFIG_FB_FOREIGN_ENDIAN is not set
> +# CONFIG_FB_SYS_FOPS is not set
> +# CONFIG_FB_WMT_GE_ROPS is not set
> +CONFIG_FB_DEFERRED_IO=y
> +# CONFIG_FB_SVGALIB is not set
> +# CONFIG_FB_MACMODES is not set
> +# CONFIG_FB_BACKLIGHT is not set
> +CONFIG_FB_MODE_HELPERS=y
> +# CONFIG_FB_TILEBLITTING is not set
> +
> +#
> +# Frame buffer hardware drivers
> +#
> +# CONFIG_FB_ARMCLCD is not set
> +# CONFIG_FB_UVESA is not set
> +# CONFIG_FB_S1D13XXX is not set
> +# CONFIG_FB_TMIO is not set
> +# CONFIG_FB_UDL is not set
> +# CONFIG_FB_VIRTUAL is not set
> +# CONFIG_FB_METRONOME is not set
> +# CONFIG_FB_BROADSHEET is not set
> +CONFIG_BACKLIGHT_LCD_SUPPORT=y
> +# CONFIG_LCD_CLASS_DEVICE is not set
> +CONFIG_BACKLIGHT_CLASS_DEVICE=y
> +# CONFIG_BACKLIGHT_GENERIC is not set
> +CONFIG_BACKLIGHT_PWM=y
> +# CONFIG_BACKLIGHT_ADP8860 is not set
> +# CONFIG_BACKLIGHT_ADP8870 is not set
> +
> +#
> +# Display device support
> +#
> +# CONFIG_DISPLAY_SUPPORT is not set
> +CONFIG_FB_MXC=y
> +CONFIG_FB_MXC_EDID=y
> +CONFIG_FB_MXC_SYNC_PANEL=y
> +# CONFIG_FB_MXC_EPSON_VGA_SYNC_PANEL is not set
> +CONFIG_FB_MXC_LDB=y
> +CONFIG_FB_MXC_MIPI_DSI=y
> +CONFIG_FB_MXC_TRULY_WVGA_SYNC_PANEL=y
> +# CONFIG_FB_MXC_CLAA_WVGA_SYNC_PANEL is not set
> +# CONFIG_FB_MXC_SEIKO_WVGA_SYNC_PANEL is not set
> +# CONFIG_FB_MXC_SII902X is not set
> +# CONFIG_FB_MXC_CH7026 is not set
> +# CONFIG_FB_MXC_TVOUT_CH7024 is not set
> +# CONFIG_FB_MXC_ASYNC_PANEL is not set
> +CONFIG_FB_MXC_EINK_PANEL=y
> +# CONFIG_FB_MXC_EINK_AUTO_UPDATE_MODE is not set
> +# CONFIG_FB_MXC_SIPIX_PANEL is not set
> +# CONFIG_FB_MXC_ELCDIF_FB is not set
> +CONFIG_FB_MXC_HDMI=y
> +
> +#
> +# Console display driver support
> +#
> +CONFIG_DUMMY_CONSOLE=y
> +CONFIG_FRAMEBUFFER_CONSOLE=y
> +# CONFIG_FRAMEBUFFER_CONSOLE_DETECT_PRIMARY is not set
> +# CONFIG_FRAMEBUFFER_CONSOLE_ROTATION is not set
> +CONFIG_FONTS=y
> +# CONFIG_FONT_8x8 is not set
> +CONFIG_FONT_8x16=y
> +# CONFIG_FONT_6x11 is not set
> +# CONFIG_FONT_7x14 is not set
> +# CONFIG_FONT_PEARL_8x8 is not set
> +# CONFIG_FONT_ACORN_8x8 is not set
> +# CONFIG_FONT_MINI_4x6 is not set
> +# CONFIG_FONT_SUN8x16 is not set
> +# CONFIG_FONT_SUN12x22 is not set
> +# CONFIG_FONT_10x18 is not set
> +CONFIG_LOGO=y
> +CONFIG_LOGO_LINUX_MONO=y
> +CONFIG_LOGO_LINUX_VGA16=y
> +CONFIG_LOGO_LINUX_CLUT224=y
> +CONFIG_SOUND=y
> +# CONFIG_SOUND_OSS_CORE is not set
> +CONFIG_SND=y
> +CONFIG_SND_TIMER=y
> +CONFIG_SND_PCM=y
> +CONFIG_SND_HWDEP=y
> +CONFIG_SND_RAWMIDI=y
> +CONFIG_SND_JACK=y
> +# CONFIG_SND_SEQUENCER is not set
> +# CONFIG_SND_MIXER_OSS is not set
> +# CONFIG_SND_PCM_OSS is not set
> +# CONFIG_SND_HRTIMER is not set
> +# CONFIG_SND_DYNAMIC_MINORS is not set
> +CONFIG_SND_SUPPORT_OLD_API=y
> +CONFIG_SND_VERBOSE_PROCFS=y
> +# CONFIG_SND_VERBOSE_PRINTK is not set
> +# CONFIG_SND_DEBUG is not set
> +# CONFIG_SND_RAWMIDI_SEQ is not set
> +# CONFIG_SND_OPL3_LIB_SEQ is not set
> +# CONFIG_SND_OPL4_LIB_SEQ is not set
> +# CONFIG_SND_SBAWE_SEQ is not set
> +# CONFIG_SND_EMU10K1_SEQ is not set
> +CONFIG_SND_DRIVERS=y
> +# CONFIG_SND_DUMMY is not set
> +# CONFIG_SND_ALOOP is not set
> +# CONFIG_SND_MTPAV is not set
> +# CONFIG_SND_SERIAL_U16550 is not set
> +# CONFIG_SND_MPU401 is not set
> +CONFIG_SND_ARM=y
> +# CONFIG_SND_ARMAACI is not set
> +CONFIG_SND_SPI=y
> +CONFIG_SND_USB=y
> +CONFIG_SND_USB_AUDIO=y
> +# CONFIG_SND_USB_UA101 is not set
> +# CONFIG_SND_USB_CAIAQ is not set
> +# CONFIG_SND_USB_6FIRE is not set
> +CONFIG_SND_SOC=y
> +# CONFIG_SND_SOC_CACHE_LZO is not set
> +CONFIG_SND_SOC_AC97_BUS=y
> +CONFIG_SND_IMX_SOC=y
> +CONFIG_SND_MXC_SOC_MX2=y
> +CONFIG_SND_MXC_SOC_SPDIF_DAI=y
> +CONFIG_SND_SOC_IMX_SGTL5000=y
> +# CONFIG_SND_SOC_IMX_WM8958 is not set
> +CONFIG_SND_SOC_IMX_WM8962=y
> +CONFIG_SND_SOC_IMX_CS42888=y
> +# CONFIG_SND_SOC_IMX_SI4763 is not set
> +CONFIG_SND_SOC_IMX_SPDIF=y
> +CONFIG_SND_SOC_IMX_HDMI=y
> +CONFIG_SND_SOC_I2C_AND_SPI=y
> +# CONFIG_SND_SOC_ALL_CODECS is not set
> +CONFIG_SND_SOC_MXC_HDMI=y
> +CONFIG_SND_SOC_MXC_SPDIF=y
> +CONFIG_SND_SOC_SGTL5000=y
> +CONFIG_SND_SOC_CS42888=y
> +CONFIG_SND_SOC_WM8962=y
> +# CONFIG_SOUND_PRIME is not set
> +CONFIG_AC97_BUS=y
> +CONFIG_HID_SUPPORT=y
> +CONFIG_HID=y
> +CONFIG_HIDRAW=y
> +
> +#
> +# USB Input Devices
> +#
> +CONFIG_USB_HID=y
> +# CONFIG_HID_PID is not set
> +# CONFIG_USB_HIDDEV is not set
> +
> +#
> +# Special HID drivers
> +#
> +CONFIG_HID_A4TECH=m
> +# CONFIG_HID_ACRUX is not set
> +CONFIG_HID_APPLE=m
> +CONFIG_HID_BELKIN=m
> +CONFIG_HID_CHERRY=m
> +CONFIG_HID_CHICONY=m
> +# CONFIG_HID_PRODIKEYS is not set
> +CONFIG_HID_CYPRESS=m
> +# CONFIG_HID_DRAGONRISE is not set
> +# CONFIG_HID_EMS_FF is not set
> +# CONFIG_HID_ELECOM is not set
> +CONFIG_HID_EZKEY=m
> +# CONFIG_HID_KEYTOUCH is not set
> +# CONFIG_HID_KYE is not set
> +# CONFIG_HID_UCLOGIC is not set
> +# CONFIG_HID_WALTOP is not set
> +CONFIG_HID_GYRATION=m
> +# CONFIG_HID_TWINHAN is not set
> +# CONFIG_HID_KENSINGTON is not set
> +# CONFIG_HID_LCPOWER is not set
> +CONFIG_HID_LOGITECH=m
> +# CONFIG_LOGITECH_FF is not set
> +# CONFIG_LOGIRUMBLEPAD2_FF is not set
> +# CONFIG_LOGIG940_FF is not set
> +# CONFIG_LOGIWII_FF is not set
> +# CONFIG_HID_MAGICMOUSE is not set
> +CONFIG_HID_MICROSOFT=m
> +CONFIG_HID_MONTEREY=m
> +# CONFIG_HID_MULTITOUCH is not set
> +# CONFIG_HID_NTRIG is not set
> +# CONFIG_HID_ORTEK is not set
> +CONFIG_HID_PANTHERLORD=m
> +# CONFIG_PANTHERLORD_FF is not set
> +CONFIG_HID_PETALYNX=m
> +# CONFIG_HID_PICOLCD is not set
> +# CONFIG_HID_QUANTA is not set
> +# CONFIG_HID_ROCCAT is not set
> +# CONFIG_HID_ROCCAT_ARVO is not set
> +# CONFIG_HID_ROCCAT_KONE is not set
> +# CONFIG_HID_ROCCAT_KONEPLUS is not set
> +# CONFIG_HID_ROCCAT_KOVAPLUS is not set
> +# CONFIG_HID_ROCCAT_PYRA is not set
> +CONFIG_HID_SAMSUNG=m
> +CONFIG_HID_SONY=m
> +CONFIG_HID_SUNPLUS=m
> +# CONFIG_HID_GREENASIA is not set
> +# CONFIG_HID_SMARTJOYPLUS is not set
> +# CONFIG_HID_TOPSEED is not set
> +# CONFIG_HID_THRUSTMASTER is not set
> +# CONFIG_HID_WACOM is not set
> +# CONFIG_HID_ZEROPLUS is not set
> +# CONFIG_HID_ZYDACRON is not set
> +CONFIG_USB_SUPPORT=y
> +CONFIG_USB_ARCH_HAS_HCD=y
> +# CONFIG_USB_ARCH_HAS_OHCI is not set
> +CONFIG_USB_ARCH_HAS_EHCI=y
> +CONFIG_USB=y
> +# CONFIG_USB_DEBUG is not set
> +# CONFIG_USB_ANNOUNCE_NEW_DEVICES is not set
> +
> +#
> +# Miscellaneous USB options
> +#
> +# CONFIG_USB_DEVICEFS is not set
> +# CONFIG_USB_DEVICE_CLASS is not set
> +# CONFIG_USB_DYNAMIC_MINORS is not set
> +CONFIG_USB_SUSPEND=y
> +CONFIG_USB_OTG=y
> +# CONFIG_USB_OTG_WHITELIST is not set
> +# CONFIG_USB_OTG_BLACKLIST_HUB is not set
> +# CONFIG_USB_MON is not set
> +# CONFIG_USB_WUSB is not set
> +# CONFIG_USB_WUSB_CBAF is not set
> +
> +#
> +# USB Host Controller Drivers
> +#
> +# CONFIG_USB_C67X00_HCD is not set
> +CONFIG_USB_EHCI_HCD=y
> +CONFIG_USB_EHCI_ARC=y
> +CONFIG_USB_EHCI_ARC_OTG=y
> +# CONFIG_USB_EHCI_ARC_HSIC is not set
> +# CONFIG_USB_STATIC_IRAM is not set
> +CONFIG_USB_EHCI_ROOT_HUB_TT=y
> +# CONFIG_USB_EHCI_TT_NEWSCHED is not set
> +# CONFIG_USB_EHCI_MXC is not set
> +# CONFIG_USB_OXU210HP_HCD is not set
> +# CONFIG_USB_ISP116X_HCD is not set
> +# CONFIG_USB_ISP1760_HCD is not set
> +# CONFIG_USB_ISP1362_HCD is not set
> +# CONFIG_USB_SL811_HCD is not set
> +# CONFIG_USB_R8A66597_HCD is not set
> +# CONFIG_USB_HWA_HCD is not set
> +# CONFIG_USB_MUSB_HDRC is not set
> +
> +#
> +# USB Device Class drivers
> +#
> +# CONFIG_USB_ACM is not set
> +# CONFIG_USB_PRINTER is not set
> +# CONFIG_USB_WDM is not set
> +# CONFIG_USB_TMC is not set
> +
> +#
> +# NOTE: USB_STORAGE depends on SCSI but BLK_DEV_SD may
> +#
> +
> +#
> +# also be needed; see USB_STORAGE Help for more info
> +#
> +CONFIG_USB_STORAGE=y
> +# CONFIG_USB_STORAGE_DEBUG is not set
> +# CONFIG_USB_STORAGE_REALTEK is not set
> +# CONFIG_USB_STORAGE_DATAFAB is not set
> +# CONFIG_USB_STORAGE_FREECOM is not set
> +# CONFIG_USB_STORAGE_ISD200 is not set
> +# CONFIG_USB_STORAGE_USBAT is not set
> +# CONFIG_USB_STORAGE_SDDR09 is not set
> +# CONFIG_USB_STORAGE_SDDR55 is not set
> +# CONFIG_USB_STORAGE_JUMPSHOT is not set
> +# CONFIG_USB_STORAGE_ALAUDA is not set
> +# CONFIG_USB_STORAGE_ONETOUCH is not set
> +# CONFIG_USB_STORAGE_KARMA is not set
> +# CONFIG_USB_STORAGE_CYPRESS_ATACB is not set
> +# CONFIG_USB_STORAGE_ENE_UB6250 is not set
> +# CONFIG_USB_UAS is not set
> +# CONFIG_USB_LIBUSUAL is not set
> +
> +#
> +# USB Imaging devices
> +#
> +# CONFIG_USB_MDC800 is not set
> +# CONFIG_USB_MICROTEK is not set
> +
> +#
> +# USB port drivers
> +#
> +# CONFIG_USB_SERIAL is not set
> +
> +#
> +# USB Miscellaneous drivers
> +#
> +# CONFIG_USB_EMI62 is not set
> +# CONFIG_USB_EMI26 is not set
> +# CONFIG_USB_ADUTUX is not set
> +# CONFIG_USB_SEVSEG is not set
> +# CONFIG_USB_RIO500 is not set
> +# CONFIG_USB_LEGOTOWER is not set
> +# CONFIG_USB_LCD is not set
> +# CONFIG_USB_LED is not set
> +# CONFIG_USB_CYPRESS_CY7C63 is not set
> +# CONFIG_USB_CYTHERM is not set
> +# CONFIG_USB_IDMOUSE is not set
> +# CONFIG_USB_FTDI_ELAN is not set
> +# CONFIG_USB_APPLEDISPLAY is not set
> +# CONFIG_USB_SISUSBVGA is not set
> +# CONFIG_USB_LD is not set
> +# CONFIG_USB_TRANCEVIBRATOR is not set
> +# CONFIG_USB_IOWARRIOR is not set
> +# CONFIG_USB_TEST is not set
> +# CONFIG_USB_ISIGHTFW is not set
> +# CONFIG_USB_YUREX is not set
> +CONFIG_USB_GADGET=y
> +# CONFIG_USB_GADGET_DEBUG_FILES is not set
> +# CONFIG_USB_GADGET_DEBUG_FS is not set
> +CONFIG_USB_GADGET_VBUS_DRAW=2
> +CONFIG_USB_GADGET_SELECTED=y
> +CONFIG_USB_GADGET_ARC=y
> +# CONFIG_IMX_USB_CHARGER is not set
> +CONFIG_USB_ARC=y
> +# CONFIG_USB_GADGET_FSL_USB2 is not set
> +# CONFIG_USB_GADGET_FUSB300 is not set
> +# CONFIG_USB_GADGET_R8A66597 is not set
> +# CONFIG_USB_GADGET_PXA_U2O is not set
> +# CONFIG_USB_GADGET_M66592 is not set
> +# CONFIG_USB_GADGET_DUMMY_HCD is not set
> +CONFIG_USB_GADGET_DUALSPEED=y
> +# CONFIG_USB_ZERO is not set
> +CONFIG_USB_AUDIO=m
> +CONFIG_USB_ETH=m
> +CONFIG_USB_ETH_RNDIS=y
> +# CONFIG_USB_ETH_EEM is not set
> +# CONFIG_USB_G_NCM is not set
> +# CONFIG_USB_GADGETFS is not set
> +# CONFIG_USB_FUNCTIONFS is not set
> +CONFIG_USB_FILE_STORAGE=m
> +# CONFIG_FSL_UTP is not set
> +# CONFIG_USB_FILE_STORAGE_TEST is not set
> +# CONFIG_USB_MASS_STORAGE is not set
> +CONFIG_USB_G_SERIAL=m
> +# CONFIG_USB_MIDI_GADGET is not set
> +# CONFIG_USB_G_PRINTER is not set
> +# CONFIG_USB_CDC_COMPOSITE is not set
> +# CONFIG_USB_G_MULTI is not set
> +# CONFIG_USB_G_HID is not set
> +# CONFIG_USB_G_DBGP is not set
> +# CONFIG_USB_G_WEBCAM is not set
> +
> +#
> +# OTG and related infrastructure
> +#
> +CONFIG_USB_OTG_UTILS=y
> +# CONFIG_USB_GPIO_VBUS is not set
> +# CONFIG_USB_ULPI is not set
> +# CONFIG_NOP_USB_XCEIV is not set
> +CONFIG_MXC_OTG=y
> +CONFIG_MMC=y
> +# CONFIG_MMC_DEBUG is not set
> +CONFIG_MMC_UNSAFE_RESUME=y
> +# CONFIG_MMC_CLKGATE is not set
> +
> +#
> +# MMC/SD/SDIO Card Drivers
> +#
> +CONFIG_MMC_BLOCK=y
> +CONFIG_MMC_BLOCK_MINORS=8
> +CONFIG_MMC_BLOCK_BOUNCE=y
> +# CONFIG_SDIO_UART is not set
> +# CONFIG_MMC_TEST is not set
> +
> +#
> +# MMC/SD/SDIO Host Controller Drivers
> +#
> +# CONFIG_MMC_ARMMMCI is not set
> +CONFIG_MMC_SDHCI=y
> +CONFIG_MMC_SDHCI_IO_ACCESSORS=y
> +CONFIG_MMC_SDHCI_PLTFM=y
> +CONFIG_MMC_SDHCI_ESDHC_IMX=y
> +# CONFIG_MMC_DW is not set
> +# CONFIG_MMC_VUB300 is not set
> +# CONFIG_MMC_USHC is not set
> +# CONFIG_MEMSTICK is not set
> +CONFIG_NEW_LEDS=y
> +CONFIG_LEDS_CLASS=y
> +
> +#
> +# LED drivers
> +#
> +# CONFIG_LEDS_LM3530 is not set
> +# CONFIG_LEDS_PCA9532 is not set
> +CONFIG_LEDS_GPIO=y
> +CONFIG_LEDS_GPIO_PLATFORM=y
> +# CONFIG_LEDS_LP3944 is not set
> +# CONFIG_LEDS_LP5521 is not set
> +# CONFIG_LEDS_LP5523 is not set
> +# CONFIG_LEDS_PCA955X is not set
> +# CONFIG_LEDS_DAC124S085 is not set
> +# CONFIG_LEDS_PWM is not set
> +# CONFIG_LEDS_REGULATOR is not set
> +# CONFIG_LEDS_BD2802 is not set
> +# CONFIG_LEDS_LT3593 is not set
> +CONFIG_LEDS_TRIGGERS=y
> +
> +#
> +# LED Triggers
> +#
> +# CONFIG_LEDS_TRIGGER_TIMER is not set
> +# CONFIG_LEDS_TRIGGER_HEARTBEAT is not set
> +# CONFIG_LEDS_TRIGGER_BACKLIGHT is not set
> +CONFIG_LEDS_TRIGGER_GPIO=y
> +CONFIG_LEDS_TRIGGER_DEFAULT_ON=y
> +
> +#
> +# iptables trigger is under Netfilter config (LED target)
> +#
> +
> +#
> +# LED Triggers
> +#
> +# CONFIG_NFC_DEVICES is not set
> +# CONFIG_ACCESSIBILITY is not set
> +CONFIG_RTC_LIB=y
> +CONFIG_RTC_CLASS=y
> +CONFIG_RTC_HCTOSYS=y
> +CONFIG_RTC_HCTOSYS_DEVICE="rtc0"
> +# CONFIG_RTC_DEBUG is not set
> +
> +#
> +# RTC interfaces
> +#
> +CONFIG_RTC_INTF_SYSFS=y
> +CONFIG_RTC_INTF_PROC=y
> +CONFIG_RTC_INTF_DEV=y
> +CONFIG_RTC_INTF_DEV_UIE_EMUL=y
> +# CONFIG_RTC_DRV_TEST is not set
> +
> +#
> +# I2C RTC drivers
> +#
> +# CONFIG_RTC_DRV_DS1307 is not set
> +# CONFIG_RTC_DRV_DS1374 is not set
> +# CONFIG_RTC_DRV_DS1672 is not set
> +# CONFIG_RTC_DRV_DS3232 is not set
> +# CONFIG_RTC_DRV_MAX6900 is not set
> +# CONFIG_RTC_DRV_RS5C372 is not set
> +# CONFIG_RTC_DRV_ISL1208 is not set
> +# CONFIG_RTC_DRV_ISL12022 is not set
> +# CONFIG_RTC_DRV_X1205 is not set
> +# CONFIG_RTC_DRV_PCF8563 is not set
> +# CONFIG_RTC_DRV_PCF8583 is not set
> +# CONFIG_RTC_DRV_M41T80 is not set
> +# CONFIG_RTC_DRV_BQ32K is not set
> +# CONFIG_RTC_DRV_S35390A is not set
> +# CONFIG_RTC_DRV_FM3130 is not set
> +# CONFIG_RTC_DRV_RX8581 is not set
> +# CONFIG_RTC_DRV_RX8025 is not set
> +# CONFIG_RTC_DRV_EM3027 is not set
> +# CONFIG_RTC_DRV_RV3029C2 is not set
> +
> +#
> +# SPI RTC drivers
> +#
> +# CONFIG_RTC_DRV_M41T93 is not set
> +# CONFIG_RTC_DRV_M41T94 is not set
> +# CONFIG_RTC_DRV_DS1305 is not set
> +# CONFIG_RTC_DRV_DS1390 is not set
> +# CONFIG_RTC_DRV_MAX6902 is not set
> +# CONFIG_RTC_DRV_R9701 is not set
> +# CONFIG_RTC_DRV_RS5C348 is not set
> +# CONFIG_RTC_DRV_DS3234 is not set
> +# CONFIG_RTC_DRV_PCF2123 is not set
> +
> +#
> +# Platform RTC drivers
> +#
> +# CONFIG_RTC_DRV_CMOS is not set
> +# CONFIG_RTC_DRV_DS1286 is not set
> +# CONFIG_RTC_DRV_DS1511 is not set
> +# CONFIG_RTC_DRV_DS1553 is not set
> +# CONFIG_RTC_DRV_DS1742 is not set
> +# CONFIG_RTC_DRV_STK17TA8 is not set
> +# CONFIG_RTC_DRV_M48T86 is not set
> +# CONFIG_RTC_DRV_M48T35 is not set
> +# CONFIG_RTC_DRV_M48T59 is not set
> +# CONFIG_RTC_DRV_MSM6242 is not set
> +# CONFIG_RTC_MXC is not set
> +# CONFIG_RTC_DRV_MXC_V2 is not set
> +CONFIG_RTC_DRV_SNVS=y
> +# CONFIG_RTC_DRV_BQ4802 is not set
> +# CONFIG_RTC_DRV_RP5C01 is not set
> +# CONFIG_RTC_DRV_V3020 is not set
> +
> +#
> +# on-CPU RTC drivers
> +#
> +# CONFIG_RTC_DRV_PL030 is not set
> +# CONFIG_RTC_DRV_PL031 is not set
> +CONFIG_DMADEVICES=y
> +# CONFIG_DMADEVICES_DEBUG is not set
> +
> +#
> +# DMA Devices
> +#
> +# CONFIG_AMBA_PL08X is not set
> +# CONFIG_DW_DMAC is not set
> +CONFIG_MXC_PXP_V2=y
> +CONFIG_MXC_PXP_CLIENT_DEVICE=y
> +# CONFIG_TIMB_DMA is not set
> +CONFIG_IMX_SDMA=y
> +CONFIG_MXS_DMA=y
> +CONFIG_DMA_ENGINE=y
> +
> +#
> +# DMA Clients
> +#
> +# CONFIG_NET_DMA is not set
> +# CONFIG_ASYNC_TX_DMA is not set
> +# CONFIG_DMATEST is not set
> +# CONFIG_AUXDISPLAY is not set
> +# CONFIG_UIO is not set
> +# CONFIG_STAGING is not set
> +CONFIG_CLKDEV_LOOKUP=y
> +CONFIG_CLKSRC_MMIO=y
> +
> +#
> +# MXC support drivers
> +#
> +CONFIG_MXC_IPU=y
> +CONFIG_MXC_IPU_V3=y
> +CONFIG_MXC_IPU_V3H=y
> +
> +#
> +# MXC SSI support
> +#
> +# CONFIG_MXC_SSI is not set
> +
> +#
> +# MXC Digital Audio Multiplexer support
> +#
> +# CONFIG_MXC_DAM is not set
> +
> +#
> +# MXC PMIC support
> +#
> +# CONFIG_MXC_PMIC_MC13783 is not set
> +# CONFIG_MXC_PMIC_MC13892 is not set
> +# CONFIG_MXC_PMIC_MC34704 is not set
> +# CONFIG_MXC_PMIC_MC9SDZ60 is not set
> +# CONFIG_MXC_PMIC_MC9S08DZ60 is not set
> +
> +#
> +# MXC Security Drivers
> +#
> +# CONFIG_MXC_SECURITY_SCC is not set
> +# CONFIG_MXC_SECURITY_RNG is not set
> +
> +#
> +# MXC MPEG4 Encoder Kernel module support
> +#
> +# CONFIG_MXC_HMP4E is not set
> +
> +#
> +# MXC HARDWARE EVENT
> +#
> +# CONFIG_MXC_HWEVENT is not set
> +
> +#
> +# MXC VPU(Video Processing Unit) support
> +#
> +CONFIG_MXC_VPU=y
> +# CONFIG_MXC_VPU_DEBUG is not set
> +# CONFIG_MX6_VPU_352M is not set
> +
> +#
> +# MXC Asynchronous Sample Rate Converter support
> +#
> +CONFIG_MXC_ASRC=y
> +
> +#
> +# MXC Bluetooth support
> +#
> +
> +#
> +# Broadcom GPS ioctrl support
> +#
> +
> +#
> +# MXC Media Local Bus Driver
> +#
> +CONFIG_MXC_MLB=y
> +CONFIG_MXC_MLB150=m
> +
> +#
> +# i.MX ADC support
> +#
> +# CONFIG_IMX_ADC is not set
> +
> +#
> +# MXC Vivante GPU support
> +#
> +CONFIG_MXC_GPU_VIV=y
> +
> +#
> +# ANATOP_THERMAL
> +#
> +CONFIG_ANATOP_THERMAL=y
> +
> +#
> +# MXC MIPI Support
> +#
> +CONFIG_MXC_MIPI_CSI2=y
> +
> +#
> +# MXC HDMI CEC (Consumer Electronics Control) support
> +#
> +# CONFIG_MXC_HDMI_CEC is not set
> +
> +#
> +# File systems
> +#
> +CONFIG_EXT2_FS=y
> +# CONFIG_EXT2_FS_XATTR is not set
> +# CONFIG_EXT2_FS_XIP is not set
> +CONFIG_EXT3_FS=y
> +# CONFIG_EXT3_DEFAULTS_TO_ORDERED is not set
> +CONFIG_EXT3_FS_XATTR=y
> +# CONFIG_EXT3_FS_POSIX_ACL is not set
> +# CONFIG_EXT3_FS_SECURITY is not set
> +CONFIG_EXT4_FS=y
> +CONFIG_EXT4_FS_XATTR=y
> +# CONFIG_EXT4_FS_POSIX_ACL is not set
> +# CONFIG_EXT4_FS_SECURITY is not set
> +# CONFIG_EXT4_DEBUG is not set
> +CONFIG_JBD=y
> +# CONFIG_JBD_DEBUG is not set
> +CONFIG_JBD2=y
> +# CONFIG_JBD2_DEBUG is not set
> +CONFIG_FS_MBCACHE=y
> +# CONFIG_REISERFS_FS is not set
> +# CONFIG_JFS_FS is not set
> +# CONFIG_XFS_FS is not set
> +# CONFIG_GFS2_FS is not set
> +# CONFIG_BTRFS_FS is not set
> +# CONFIG_NILFS2_FS is not set
> +# CONFIG_FS_POSIX_ACL is not set
> +CONFIG_FILE_LOCKING=y
> +CONFIG_FSNOTIFY=y
> +CONFIG_DNOTIFY=y
> +CONFIG_INOTIFY_USER=y
> +# CONFIG_FANOTIFY is not set
> +# CONFIG_QUOTA is not set
> +# CONFIG_QUOTACTL is not set
> +CONFIG_AUTOFS4_FS=m
> +# CONFIG_FUSE_FS is not set
> +
> +#
> +# Caches
> +#
> +# CONFIG_FSCACHE is not set
> +
> +#
> +# CD-ROM/DVD Filesystems
> +#
> +# CONFIG_ISO9660_FS is not set
> +# CONFIG_UDF_FS is not set
> +
> +#
> +# DOS/FAT/NT Filesystems
> +#
> +CONFIG_FAT_FS=y
> +CONFIG_MSDOS_FS=y
> +CONFIG_VFAT_FS=y
> +CONFIG_FAT_DEFAULT_CODEPAGE=437
> +CONFIG_FAT_DEFAULT_IOCHARSET="iso8859-1"
> +# CONFIG_NTFS_FS is not set
> +
> +#
> +# Pseudo filesystems
> +#
> +CONFIG_PROC_FS=y
> +CONFIG_PROC_SYSCTL=y
> +CONFIG_PROC_PAGE_MONITOR=y
> +CONFIG_SYSFS=y
> +CONFIG_TMPFS=y
> +# CONFIG_TMPFS_POSIX_ACL is not set
> +# CONFIG_TMPFS_XATTR is not set
> +# CONFIG_HUGETLB_PAGE is not set
> +# CONFIG_CONFIGFS_FS is not set
> +CONFIG_MISC_FILESYSTEMS=y
> +# CONFIG_ADFS_FS is not set
> +# CONFIG_AFFS_FS is not set
> +# CONFIG_HFS_FS is not set
> +# CONFIG_HFSPLUS_FS is not set
> +# CONFIG_BEFS_FS is not set
> +# CONFIG_BFS_FS is not set
> +# CONFIG_EFS_FS is not set
> +CONFIG_JFFS2_FS=y
> +CONFIG_JFFS2_FS_DEBUG=0
> +CONFIG_JFFS2_FS_WRITEBUFFER=y
> +# CONFIG_JFFS2_FS_WBUF_VERIFY is not set
> +# CONFIG_JFFS2_SUMMARY is not set
> +# CONFIG_JFFS2_FS_XATTR is not set
> +# CONFIG_JFFS2_COMPRESSION_OPTIONS is not set
> +CONFIG_JFFS2_ZLIB=y
> +# CONFIG_JFFS2_LZO is not set
> +CONFIG_JFFS2_RTIME=y
> +# CONFIG_JFFS2_RUBIN is not set
> +CONFIG_UBIFS_FS=y
> +# CONFIG_UBIFS_FS_XATTR is not set
> +# CONFIG_UBIFS_FS_ADVANCED_COMPR is not set
> +CONFIG_UBIFS_FS_LZO=y
> +CONFIG_UBIFS_FS_ZLIB=y
> +# CONFIG_UBIFS_FS_DEBUG is not set
> +# CONFIG_LOGFS is not set
> +CONFIG_CRAMFS=y
> +# CONFIG_SQUASHFS is not set
> +# CONFIG_VXFS_FS is not set
> +# CONFIG_MINIX_FS is not set
> +# CONFIG_OMFS_FS is not set
> +# CONFIG_HPFS_FS is not set
> +# CONFIG_QNX4FS_FS is not set
> +# CONFIG_ROMFS_FS is not set
> +# CONFIG_PSTORE is not set
> +# CONFIG_SYSV_FS is not set
> +# CONFIG_UFS_FS is not set
> +CONFIG_NETWORK_FILESYSTEMS=y
> +CONFIG_NFS_FS=y
> +CONFIG_NFS_V3=y
> +# CONFIG_NFS_V3_ACL is not set
> +# CONFIG_NFS_V4 is not set
> +CONFIG_ROOT_NFS=y
> +# CONFIG_NFSD is not set
> +CONFIG_LOCKD=y
> +CONFIG_LOCKD_V4=y
> +CONFIG_NFS_COMMON=y
> +CONFIG_SUNRPC=y
> +# CONFIG_CEPH_FS is not set
> +# CONFIG_CIFS is not set
> +# CONFIG_NCP_FS is not set
> +# CONFIG_CODA_FS is not set
> +# CONFIG_AFS_FS is not set
> +
> +#
> +# Partition Types
> +#
> +CONFIG_PARTITION_ADVANCED=y
> +# CONFIG_ACORN_PARTITION is not set
> +# CONFIG_OSF_PARTITION is not set
> +# CONFIG_AMIGA_PARTITION is not set
> +# CONFIG_ATARI_PARTITION is not set
> +# CONFIG_MAC_PARTITION is not set
> +CONFIG_MSDOS_PARTITION=y
> +# CONFIG_BSD_DISKLABEL is not set
> +# CONFIG_MINIX_SUBPARTITION is not set
> +# CONFIG_SOLARIS_X86_PARTITION is not set
> +# CONFIG_UNIXWARE_DISKLABEL is not set
> +# CONFIG_LDM_PARTITION is not set
> +# CONFIG_SGI_PARTITION is not set
> +# CONFIG_ULTRIX_PARTITION is not set
> +# CONFIG_SUN_PARTITION is not set
> +# CONFIG_KARMA_PARTITION is not set
> +CONFIG_EFI_PARTITION=y
> +# CONFIG_SYSV68_PARTITION is not set
> +CONFIG_NLS=y
> +CONFIG_NLS_DEFAULT="iso8859-1"
> +CONFIG_NLS_CODEPAGE_437=y
> +# CONFIG_NLS_CODEPAGE_737 is not set
> +# CONFIG_NLS_CODEPAGE_775 is not set
> +# CONFIG_NLS_CODEPAGE_850 is not set
> +# CONFIG_NLS_CODEPAGE_852 is not set
> +# CONFIG_NLS_CODEPAGE_855 is not set
> +# CONFIG_NLS_CODEPAGE_857 is not set
> +# CONFIG_NLS_CODEPAGE_860 is not set
> +# CONFIG_NLS_CODEPAGE_861 is not set
> +# CONFIG_NLS_CODEPAGE_862 is not set
> +# CONFIG_NLS_CODEPAGE_863 is not set
> +# CONFIG_NLS_CODEPAGE_864 is not set
> +# CONFIG_NLS_CODEPAGE_865 is not set
> +# CONFIG_NLS_CODEPAGE_866 is not set
> +# CONFIG_NLS_CODEPAGE_869 is not set
> +# CONFIG_NLS_CODEPAGE_936 is not set
> +# CONFIG_NLS_CODEPAGE_950 is not set
> +# CONFIG_NLS_CODEPAGE_932 is not set
> +# CONFIG_NLS_CODEPAGE_949 is not set
> +# CONFIG_NLS_CODEPAGE_874 is not set
> +# CONFIG_NLS_ISO8859_8 is not set
> +# CONFIG_NLS_CODEPAGE_1250 is not set
> +# CONFIG_NLS_CODEPAGE_1251 is not set
> +CONFIG_NLS_ASCII=m
> +CONFIG_NLS_ISO8859_1=y
> +# CONFIG_NLS_ISO8859_2 is not set
> +# CONFIG_NLS_ISO8859_3 is not set
> +# CONFIG_NLS_ISO8859_4 is not set
> +# CONFIG_NLS_ISO8859_5 is not set
> +# CONFIG_NLS_ISO8859_6 is not set
> +# CONFIG_NLS_ISO8859_7 is not set
> +# CONFIG_NLS_ISO8859_9 is not set
> +# CONFIG_NLS_ISO8859_13 is not set
> +# CONFIG_NLS_ISO8859_14 is not set
> +# CONFIG_NLS_ISO8859_15 is not set
> +# CONFIG_NLS_KOI8_R is not set
> +# CONFIG_NLS_KOI8_U is not set
> +CONFIG_NLS_UTF8=m
> +
> +#
> +# Kernel hacking
> +#
> +# CONFIG_PRINTK_TIME is not set
> +CONFIG_DEFAULT_MESSAGE_LOGLEVEL=4
> +CONFIG_ENABLE_WARN_DEPRECATED=y
> +CONFIG_ENABLE_MUST_CHECK=y
> +CONFIG_FRAME_WARN=1024
> +CONFIG_MAGIC_SYSRQ=y
> +# CONFIG_STRIP_ASM_SYMS is not set
> +# CONFIG_UNUSED_SYMBOLS is not set
> +CONFIG_DEBUG_FS=y
> +# CONFIG_HEADERS_CHECK is not set
> +# CONFIG_DEBUG_SECTION_MISMATCH is not set
> +# CONFIG_DEBUG_KERNEL is not set
> +# CONFIG_HARDLOCKUP_DETECTOR is not set
> +# CONFIG_SLUB_DEBUG_ON is not set
> +# CONFIG_SLUB_STATS is not set
> +# CONFIG_SPARSE_RCU_POINTER is not set
> +CONFIG_DEBUG_BUGVERBOSE=y
> +# CONFIG_DEBUG_MEMORY_INIT is not set
> +CONFIG_RCU_CPU_STALL_TIMEOUT=60
> +CONFIG_RCU_CPU_STALL_VERBOSE=y
> +# CONFIG_LKDTM is not set
> +CONFIG_SYSCTL_SYSCALL_CHECK=y
> +CONFIG_HAVE_FUNCTION_TRACER=y
> +CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y
> +CONFIG_HAVE_DYNAMIC_FTRACE=y
> +CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y
> +CONFIG_HAVE_C_RECORDMCOUNT=y
> +CONFIG_TRACING_SUPPORT=y
> +# CONFIG_FTRACE is not set
> +# CONFIG_DYNAMIC_DEBUG is not set
> +# CONFIG_DMA_API_DEBUG is not set
> +# CONFIG_ATOMIC64_SELFTEST is not set
> +# CONFIG_SAMPLES is not set
> +CONFIG_HAVE_ARCH_KGDB=y
> +# CONFIG_TEST_KSTRTOX is not set
> +# CONFIG_STRICT_DEVMEM is not set
> +CONFIG_ARM_UNWIND=y
> +# CONFIG_DEBUG_USER is not set
> +CONFIG_OC_ETM=y
> +
> +#
> +# Security options
> +#
> +# CONFIG_KEYS is not set
> +# CONFIG_SECURITY_DMESG_RESTRICT is not set
> +# CONFIG_SECURITY is not set
> +# CONFIG_SECURITYFS is not set
> +CONFIG_DEFAULT_SECURITY_DAC=y
> +CONFIG_DEFAULT_SECURITY=""
> +CONFIG_CRYPTO=y
> +
> +#
> +# Crypto core or helper
> +#
> +CONFIG_CRYPTO_ALGAPI=y
> +CONFIG_CRYPTO_ALGAPI2=y
> +CONFIG_CRYPTO_AEAD=y
> +CONFIG_CRYPTO_AEAD2=y
> +CONFIG_CRYPTO_BLKCIPHER=y
> +CONFIG_CRYPTO_BLKCIPHER2=y
> +CONFIG_CRYPTO_HASH=y
> +CONFIG_CRYPTO_HASH2=y
> +CONFIG_CRYPTO_RNG=y
> +CONFIG_CRYPTO_RNG2=y
> +CONFIG_CRYPTO_PCOMP2=y
> +CONFIG_CRYPTO_MANAGER=y
> +CONFIG_CRYPTO_MANAGER2=y
> +# CONFIG_CRYPTO_MANAGER_DISABLE_TESTS is not set
> +CONFIG_CRYPTO_GF128MUL=y
> +# CONFIG_CRYPTO_NULL is not set
> +# CONFIG_CRYPTO_PCRYPT is not set
> +CONFIG_CRYPTO_WORKQUEUE=y
> +# CONFIG_CRYPTO_CRYPTD is not set
> +CONFIG_CRYPTO_AUTHENC=y
> +CONFIG_CRYPTO_TEST=m
> +# CONFIG_CRYPTO_CRYPTODEV is not set
> +
> +#
> +# Authenticated Encryption with Associated Data
> +#
> +CONFIG_CRYPTO_CCM=y
> +CONFIG_CRYPTO_GCM=y
> +CONFIG_CRYPTO_SEQIV=y
> +
> +#
> +# Block modes
> +#
> +CONFIG_CRYPTO_CBC=y
> +CONFIG_CRYPTO_CTR=y
> +CONFIG_CRYPTO_CTS=y
> +CONFIG_CRYPTO_ECB=y
> +CONFIG_CRYPTO_LRW=y
> +CONFIG_CRYPTO_PCBC=y
> +CONFIG_CRYPTO_XTS=y
> +
> +#
> +# Hash modes
> +#
> +# CONFIG_CRYPTO_HMAC is not set
> +# CONFIG_CRYPTO_XCBC is not set
> +# CONFIG_CRYPTO_VMAC is not set
> +
> +#
> +# Digest
> +#
> +# CONFIG_CRYPTO_CRC32C is not set
> +CONFIG_CRYPTO_GHASH=y
> +# CONFIG_CRYPTO_MD4 is not set
> +# CONFIG_CRYPTO_MD5 is not set
> +CONFIG_CRYPTO_MICHAEL_MIC=y
> +# CONFIG_CRYPTO_RMD128 is not set
> +# CONFIG_CRYPTO_RMD160 is not set
> +# CONFIG_CRYPTO_RMD256 is not set
> +# CONFIG_CRYPTO_RMD320 is not set
> +# CONFIG_CRYPTO_SHA1 is not set
> +# CONFIG_CRYPTO_SHA256 is not set
> +# CONFIG_CRYPTO_SHA512 is not set
> +# CONFIG_CRYPTO_TGR192 is not set
> +# CONFIG_CRYPTO_WP512 is not set
> +
> +#
> +# Ciphers
> +#
> +CONFIG_CRYPTO_AES=y
> +# CONFIG_CRYPTO_ANUBIS is not set
> +CONFIG_CRYPTO_ARC4=y
> +# CONFIG_CRYPTO_BLOWFISH is not set
> +# CONFIG_CRYPTO_CAMELLIA is not set
> +# CONFIG_CRYPTO_CAST5 is not set
> +# CONFIG_CRYPTO_CAST6 is not set
> +CONFIG_CRYPTO_DES=y
> +# CONFIG_CRYPTO_FCRYPT is not set
> +# CONFIG_CRYPTO_KHAZAD is not set
> +# CONFIG_CRYPTO_SALSA20 is not set
> +# CONFIG_CRYPTO_SEED is not set
> +# CONFIG_CRYPTO_SERPENT is not set
> +# CONFIG_CRYPTO_TEA is not set
> +# CONFIG_CRYPTO_TWOFISH is not set
> +
> +#
> +# Compression
> +#
> +CONFIG_CRYPTO_DEFLATE=y
> +# CONFIG_CRYPTO_ZLIB is not set
> +CONFIG_CRYPTO_LZO=y
> +
> +#
> +# Random Number Generation
> +#
> +# CONFIG_CRYPTO_ANSI_CPRNG is not set
> +# CONFIG_CRYPTO_USER_API_HASH is not set
> +# CONFIG_CRYPTO_USER_API_SKCIPHER is not set
> +CONFIG_CRYPTO_HW=y
> +CONFIG_CRYPTO_DEV_FSL_CAAM=y
> +CONFIG_CRYPTO_DEV_FSL_CAAM_RINGSIZE=9
> +CONFIG_CRYPTO_DEV_FSL_CAAM_INTC=y
> +CONFIG_CRYPTO_DEV_FSL_CAAM_INTC_COUNT_THLD=255
> +CONFIG_CRYPTO_DEV_FSL_CAAM_INTC_TIME_THLD=2048
> +CONFIG_CRYPTO_DEV_FSL_CAAM_CRYPTO_API=y
> +CONFIG_CRYPTO_DEV_FSL_CAAM_AHASH_API=y
> +CONFIG_CRYPTO_DEV_FSL_CAAM_RNG_API=y
> +# CONFIG_CRYPTO_DEV_FSL_CAAM_RNG_TEST is not set
> +CONFIG_CRYPTO_DEV_FSL_CAAM_SM=y
> +CONFIG_CRYPTO_DEV_FSL_CAAM_SM_SLOTSIZE=7
> +CONFIG_CRYPTO_DEV_FSL_CAAM_SM_TEST=y
> +CONFIG_CRYPTO_DEV_FSL_CAAM_SECVIO=y
> +# CONFIG_BINARY_PRINTF is not set
> +
> +#
> +# Library routines
> +#
> +CONFIG_BITREVERSE=y
> +CONFIG_RATIONAL=y
> +CONFIG_CRC_CCITT=m
> +CONFIG_CRC16=y
> +# CONFIG_CRC_T10DIF is not set
> +# CONFIG_CRC_ITU_T is not set
> +CONFIG_CRC32=y
> +# CONFIG_CRC7 is not set
> +# CONFIG_LIBCRC32C is not set
> +CONFIG_ZLIB_INFLATE=y
> +CONFIG_ZLIB_DEFLATE=y
> +CONFIG_LZO_COMPRESS=y
> +CONFIG_LZO_DECOMPRESS=y
> +# CONFIG_XZ_DEC is not set
> +# CONFIG_XZ_DEC_BCJ is not set
> +CONFIG_GENERIC_ALLOCATOR=y
> +CONFIG_HAS_IOMEM=y
> +CONFIG_HAS_IOPORT=y
> +CONFIG_HAS_DMA=y
> +CONFIG_CPU_RMAP=y
> +CONFIG_NLATTR=y
> +# CONFIG_AVERAGE is not set
> diff --git a/recipes-kernel/linux/linux-imx_3.0.35.bbappend b/recipes-kernel/linux/linux-imx_3.0.35.bbappend
> new file mode 100644
> index 0000000..7554c66
> --- /dev/null
> +++ b/recipes-kernel/linux/linux-imx_3.0.35.bbappend
> @@ -0,0 +1,8 @@
> +FILESEXTRAPATHS_prepend := "${THISDIR}/${PN}-${PV}:"
> +
> +PRINC := "${@int(PRINC) + 1}"
> +
> +# Wandboard-specific patches
> +SRC_URI_append_wandboard-dual= " \
> + file://Initial-kernel-support-for-Wandboard.patch \
> +"
> --
> 1.7.9.5
>
> _______________________________________________
> meta-freescale mailing list
> meta-freescale at yoctoproject.org
> https://lists.yoctoproject.org/listinfo/meta-freescale
--
Otavio Salvador O.S. Systems
E-mail: otavio at ossystems.com.br http://www.ossystems.com.br
Mobile: +55 53 9981-7854 http://projetos.ossystems.com.br
More information about the meta-freescale
mailing list